ValvesHome > Offers to Sell > Tools & Hardware > Mechanical Hardware > Valves
10/6/23 5:45 GMT
AAK Hydraulic Relief Valves Resistant to 450Bar High Pressure
Logan, a British customer, checked with 10 hydraulic valve manufacturers that he often contacted, none of them can make a hydraulic relief valve with high pressure resistance of 450Bar. Only AAK solved the problem of high pressure resistance with 68HRC material and ensured the performance of 2 million times. According to the requirements of the engineer, Logan defines the material hardness of the hydraulic relief valve as above 68HRC, which is 10% higher than that of the conventional hydraulic relief valves. After a round of consultation, 8 hydraulic valve manufacturers gave up, and the other 2 old hydraulic relief valve suppliers tried to make samples. 2 weeks later, the hardness of the samples of the 2 hydraulic relief valve suppliers remained at 63-65HRC, which was their maximum capability. Logan had no choice but to look for the manufacturer of hydraulic relief valves again. Logan consulted 20 companies online, and they all said that they were not confident to try 68HRC materials and 450Bar high-pressure hydraulic relief valves. Logan was in a big headache. Logan found some articles of AAK about the 450Bar high-pressure hydraulic valves on the B2B website, including 68HRC materials. He emailed the drawing of hydraulic relief valve directly to AAK and asked AAK for samples. After communication, we learned that the sample of this hydraulic relief valve was stuck on the material hardness. I told him that 68HRC material was a must for the hydraulic relief valves with high pressure resistance of 450Bar, otherwise the service life of 2 million times could not be guaranteed. AAK can send the hydraulic relief valve samples in 2 weeks, but the development cost of US$1,200 for the trial order needs to be paid first. Logan seemed to have concerns. I said with a smile that AAK publishes articles on solving the difficult problems of hydraulic valves on the Internet every day. If it's only for your $1,200, our time is not worth it. Logan was instantly relieved and informed the financial department of the payment. He was surprised that the manufacturers he contacted could not make the high-pressure hydraulic relief valves, and AAK had solved the 68HRC material very early. AAK has 3 points to ensure that the material can reach 68HRC, which is also the reason why most hydraulic valve manufacturers are uncertain. 1、The imported alloy billet is selected to replace carbon steel, and then the billet is forged at high temperature, and the hardness of the material is increased by at least 3-5%. 2、Quenching and tempering heat treatment shall be conducted after forging: 2 high-temperature normalizing + 2 high-temperature tempering shall be adopted, and each time the insulation shall not be less than 15 minutes. There are tips for controlling the temperature range. 3、After tempering treatment, the workpiece is cooled to room temperature by combining water cooling and air cooling. Firstly, the workpiece is water cooled to 475-485°C at a cooling rate of 8-9°C/s, then air cooled to 325-345°C, then water cooled to 195-2050°C at a cooling rate of 4-5°C/s, and then air cooled to room temperature. In this 4-step process, most hydraulic relief valve manufacturers only take 2 steps. 2 weeks later, the hydraulic relief valve samples of AAK were sent out. Logan told me 1 week after receiving the samples that AAK hydraulic relief valve was not only resistant to high pressure, but also the material hardness of each part reached the standard. AAK hydraulic relief valves, high pressure resistant, long life, welcome to try! https://www.aakindustry.com/info-d , etail/hydraulic-relief-valves-aak326 Contact:
Phone: Fax: Email: AAK INDUSTRY CO., LTD
Bona Business Building, No. 456 Taikang Middle Road Ningbo 315100 China 10/6/23 5:45 GMT
AAK Hydraulic Cartridge Valve Manufacturer 6 Views about ChatGPT
Recently, ChatGPT is so hot that the system can't bear the surging traffic. Last November, after ChatGPT went online, Paul Buchheit from Gmail predicted that Google would be overturned in 1 or 2 years, based on the fact that technological progress would change the way people access information. These days, I try ChatGPT every day. I use 3 kinds of titles to ask ChatGPT for help to generate 800-word articles. 1. Title of information or data: common problems and maintenance methods of hydraulic cartridge valves. 2. The title of personalized category: AAK Hydraulic Manifolds, based on 3 points, has attracted 3 types of customers. 3. Title of the innovation category: After 4 proofing and 3 material changes were made, AAK was awarded a big order of cartridge valves by HydraForce finally According to the generated content of the article and my superficial feeling, to say something negative first: 1. The selling points and purchase reasons of AAK hydraulic cartridge valves must be refined and organized by professional 5-know people who understand cartridge valves. 2. The hydraulic cartridge valve article written by ChatGPT is basically correct nonsense, except for information or data. 3. The creativity of human brain on hydraulic cartridge valve is infinite, and ChatGPT's creativity on hydraulic cartridge valve still needs data accumulation. Then say something positive: 1.100% can write general articles instead of some liberal arts students because it is armed by "machine learning". 2. It is helpful and even forward-looking for writing articles about consumer goods and consumables (such as beverages, bread, etc.). 3. You know the content, but the expression is very stiff. ChatGPT can help you overcome it, not only smooth, but also more orderly. The arrival of ChatGPT can't be said to be subversive, at least it will change the way of search engines. Because no matter what proposition it is, it needs preconditions. 1. For example, brand and trust depend on what kind of products. Cheap things should be branded, and expensive things should be trusted. Drinks should have brands and hydraulic cartridge valves should have trust. 2. For example, cognition and skills, which is important? The prerequisite is that you are an elite or a grassroots. The gap between grass roots and grass roots is not cognition, but skills to make money. The gap between the elite and the elite is not the skill, but the perception of making money. 3. Does copywriting emphasize the importance of tone or product? The prerequisite is that you are a big brand or a grassroots. Nike shoes can say Just do it. They are qualified not to talk about products, but to talk about realm. Grassroots say Just do it, how many people do you think will pay? Believe it or not, I don't believe it. No matter ChatGPT, or subversive technology, they both need preconditions. Good people see good things, and shameless people see shameless things. Those who engage in the manufacturing of hydraulic cartridge valves, only do well themselves, embrace new technologies, be kind and work hard. AAK, a hydraulic cartridge valve manufacturer in China, do business with mindfulness, make friends with good intentions. https://www.aakindustry.com/info-detail/hy , draulic-cartridge-valve- manufacturers-aak497 Contact:
Phone: Fax: Email: AAK INDUSTRY CO., LTD
Bona Business Building, No. 456 Taikang Middle Road Ningbo 315100 China 10/6/23 5:44 GMT
AAK, China Top Hydraulic Cartridge Valve Manufacturer of Brand Hydraulics
Yesterday, I saw a report in the New York Times: "China's economic slowdown has brought difficulties to the United States and the world.". It seems that now it's China's turn to catch a cold, and the world will sneeze. During this period, the domestic financial and economic columns have become more and more confused. There are both pessimistic and optimistic views on China's economy, but it seems that most of the big news are always pessimistic. At present, there are indeed difficulties, but China has its own special 3 trumps: autonomy and independence, a complete industrial and technological chain, and the world's largest economy. I don't like pessimistic views and remarks very much. Foreign media have been criticizing China for decades, and some domestic elites have also been singing along. However, China has become the second largest economy in the world. Facts have proved that China's progress is wave like, which is the same as making hydraulic cartridge valves. The hydraulic cartridge valve manufacturers are also wave like in their development. In fact, people are also like this. Few people have made great progress from birth. Whether you can stand on the wave head, and whether you can stand on the wave bottom. Therefore, I am still optimistic. Maybe the pessimist is right, but the optimist has been successful. There is a long way to go. Anyway, keep faith and always believe that good things will happen soon. Maybe the probability of success will be higher. In the manufacturing industry, especially the mechanical parts with high technical content such as hydraulic valves, they are slow, stupid, and solid, and they are the efforts of smart people. There is no shortcut on this road. There is no safe haven. If without manufacturing quality 1 lead in the front, and any more 0 after it, it will return to zero after all. AAK Hydraulic Valve, starting from the first sample of foreign trade, must be benchmarked with international first-class brands in terms of quality awareness. This is also the fundamental reason for being able to supply hydraulic valves to 7 of the world's top 500 enterprises. AAK hydraulic valve's 3-point insistence (manufacturing quality, function and performance) is beyond the reach of peers. Manufacturing quality of AAK Hydraulic Valves: 1)Material selection: replace brand material A with A+ material 2)The accuracy of precision parts of the valves can reach within 2 microns (such as roundness and cylindricity) 3)4 inspections for each valve (precision dimension of machined parts, tightness of assembly, pressure test and random fatigue test) AAK Hydraulic Valves Function: Benchmark original brand samples: the internal leakage, such as check valves, shall be controlled at 2drops/min; For example, pressure control valve, direct acting relief valve RV10-20A, with an opening and closing rate of 85%; For example, the flow control valve FD50-45 has a diversion accuracy of 10% AAK Hydraulic Valves Performance: The service life of the conventional valves can reach 1.5 million times, and the customized valves can reach 2 million times. AAK Hydraulic Valve has made a good quality positioning and maintained an optimistic attitude. No matter how far the road is, it will eventually arrive. https://www.aakindustry.com/info-de , tail/hydraulic-cartridge-valves-aak325 Contact:
Phone: Fax: Email: AAK INDUSTRY CO., LTD
Bona Business Building, No. 456 Taikang Middle Road Ningbo 315100 China 10/6/23 5:43 GMT
AAK Hydraulic Check Valve with Length Diameter Ratio of 25:1
For the hydraulic check valve with the length diameter ratio of 25:1, Andrew contacted with more than 20 hydraulic check valve manufacturers online and offline in 1 week, but none of them was willing to offer. The boss was very dissatisfied and Andrew was very headache. Andrew from Spain left a message on AAK Hydraulic Valve website some time ago: can you make samples for a hydraulic check valve with a length diameter ratio of 25:1? After communication, we learned about his current purchasing situation. Because he saw on B2B that AAK published an article on the length diameter ratio of a hydraulic relief valve, then he contacted us with a try attitude. According to Andrew's drawings, it is a long and thin shaft hydraulic check valve with very complex structure. No wonder no hydraulic valve manufacturer is willing to offer. I told him that this hydraulic check valve has a length to diameter ratio of 25:1, which was 5 times that of conventional valves, and it was difficult to cut. Especially in terms of accuracy, it was very particular about equipment, operators and technology. We are willing to make samples. If AAK sample fails, there is no need to find the hydraulic check valve manufacturer in Ningbo. Andrew may have no choice but to accept the sample first and then quote. After 10 days, AAK sent 3 hydraulic check valve samples. The key to machining the thin and long shaft of this hydraulic check valve is how to control the thermal deformation of the workpiece. During cutting, the workpiece is high in temperature and easy to deform. On the 3rd day after Andrew received the samples, he informed by email that his team had approved that AAK hydraulic check valves not only had the length diameter ratio of 25:1 in place, but also had the surface roughness and geometric accuracy up to standard. For hydraulic cartridge valves with large length diameter ratio, AAK has accumulated the following 3 experiences after years of exploration: 1. Drill and fixture: long drill to be matched from hardness, heat resistance and impact toughness. When the clamping method of one clamp and one top is adopted, the elastic movable center is also used to compensate the thermal deformation and elongation, so that the elongated shaft can be freely extended after being heated to avoid thermal deformation. 2. Cutting amount and cutting fluid: according to the length diameter ratio, the drilling amount is reasonably selected. This is a skill. During cutting, the cutting fluid shall be poured sufficiently to suppress the rise of the working temperature and thus the thermal deformation. 3. The tool shall be kept sharp and the tool changing frequency shall be increased to 3 times. It can effectively reduce the friction heat between the tool and the workpiece, and control the thermal deformation from the source. This morning, I received the PO for this hydraulic check valve from Andrew. He told me that although the customer complained that their quotation was slow, they were the fastest and the only supplier of the sample success at only one time. AAK hydraulic check valve, with unique skills on the length diameter ratio, welcome to try! https://www.aakindustry.com/info-detai , l/hydraulic-check-valves-aak324 Contact:
Phone: Fax: Email: AAK INDUSTRY CO., LTD
Bona Business Building, No. 456 Taikang Middle Road Ningbo 315100 China 10/6/23 5:43 GMT
AAK Hydraulic Valve Block Processing with Deep Holes and Large Holes
Torsten is from the Netherlands. As an old purchaser, he is very handy in the hydraulic industry. Unexpectedly, he fell on a hydraulic valve block with 24 deep holes and large holes. In the second half of last year, his company developed a large-scale hydraulic windlass for ships. The hydraulic valve block used was sampled from a hydraulic valve block manufacturer in the Netherlands, but the machine running test was not smooth. After the equipment has been operated for 8 hours, there is leakage at the installation hole of the hydraulic valve block. After eliminating the suspected quality of the hydraulic cartridge valves, the engineer inspected the installation hole of the hydraulic valve block and found that the center position of the hole was offset. The original manufacturer of the hydraulic valve block feedback that it is caused by the deviation of the drill bit, and a new sample is required. However, although the processing accuracy of the second sample was improved, there was still leakage 1 month later. Now the equipment is waiting to be put into production. Their engineers have push Torsten 3 times. He can only look for new hydraulic valve block manufacturers. Torsten contacted more than 10 manufacturers and asked if they could process the hydraulic valve blocks with 24 deep holes and large holes. Only 2 manufacturers were willing to try, but they were not 100% sure. Torsten left message on AAK website: how to control the accuracy of the hydraulic valve blocks with 24 deep holes and large holes? At first, I thought it was from a peer of hydraulic valve blocks, and ignored it. It was not until Torsten sent three-dimensional and two-dimensional drawings of the hydraulic valve block that I knew the difficulties he had encountered. I told him that AAK had produced similar hydraulic valve blocks with large holes and deep holes. After 28 days, 5 hydraulic valve blocks were sent. 3 months later, Torsten sent an order for 500 hydraulic valve blocks. He specially reminded that the accuracy of the mass production must be the same as that of the samples. AAK is the only manufacturer of hydraulic valve blocks whose samples passed the test. AAK hydraulic valve blocks, for the processing of deep holes and large holes, there are 3 details: 1. Before the hydraulic valve block is processed, the clamping stiffness of the tool shall be verified to avoid the insufficient clamping stiffness of the drill bit, which may cause the drill bit to deviate and cause the processing hole to be slightly elliptical. 2. During the processing of the hydraulic valve blocks, a small drill bit smaller than the processing size is used for pre drilling. The deeper the drill bit is drilled, the easier it is to deviate from the predetermined axis, resulting in the deviation of the center position of the processing hole. The secondary processing of AAK can ensure that the drill bit does not deviate. At the same time, the feed amount and speed setting of the tool are strictly subdivided, so that the cutting chips can be timely excluded from the hole. Most hydraulic valve block manufacturers suffer from this link. Cutting chips are accumulated at the end, affecting the roughness of the valve hole and the processing of the drill bit, leaving hidden dangers for later leakage. 3. After the hydraulic valve block is processed, the center position, roughness and roundness of the processed hole shall be checked one by one. AAK hydraulic valve blocks, is not afraid of deep holes, nor slender holes, nor large holes, no deviation. You can also try a small order! https://www.aakindustry.com/info-det , ail/hydraulic-valve-blocks-aak323 Contact:
Phone: Fax: Email: AAK INDUSTRY CO., LTD
Bona Business Building, No. 456 Taikang Middle Road Ningbo 315100 China 10/6/23 5:42 GMT
Pressure Reducing/Relieving Cartridge Valve Benchmarking HydraForce PR10-36
This week, we’d like to introduce a hydraulic cartridge valve equivalent to HydraForce PR10-36. It is a spool type, pilot operated, hydraulic pressure reducing/ relieving valve with internal pilot and internal spring chamber drain, designed to act as a pressure regulating device for secondary circuits. Last January in 2022, a customer in Russia found AAK when looking for a hydraulic cartridge valve manufacturer in China on Google. She sent us an inquiry for 10 pcs of HydraForce cartridge valve PR10-36, along with several other HydraForce standard parts. However, AAK did not have existing programming for PR10-36 and did not quote. Instead, the customer placed trial order for the other models. This January in 2023, the customer checked with us again if AAK is willing to develop PR10-36 as per their original samples. Although they can buy PR10-36 from other hydraulic cartridge valve manufacturers in China, they do not trust their quality. Because the quality of the trial orders shipped by AAK last year was very satisfying, they want to develop PR10-36 with AAK. In March, the development was finished and delivered. Last week, we were very happy to learn from the Russian customer that the E- PR10-36 Pressure Reducing/Relieving Cartridge Valve developed by AAK is running very smoothly, the quality is very stable. They are going to ask AAK to develop more and more new models. AAK hydraulic cartridge valve E-PR10-36 two advantages: 1. Pressure Rating 210 bar (3000 psi), benchmarking HydraForce 2. Its service life is 2 times that of its domestic peers Technical parameters of AAK E-PR10-36 pressure reducing/relieving cartridge valve: Working Pressure: 210 bar (3000 psi) Proof Pressure: 390 bar (5700 psi) Flow Rating: 56.8 lpm (15 gpm) Pilot orifice: 0.51 mm (0.020 in) Temperature Range: -40°C ~ +120 °C (with Buna N seals) Fluids: Mineral based or synthetic hydraulic fluid with lubricating properties Fluid viscosity range: 7.4 to 420 cSt (50 to 2000 ssu) Cavity: 10-3 AAK E-PR10-36 pressure reducing/relieving cartridge valve, benchmarking HydraForce PR10-36, has been approved by customer in Russia. You are welcome to give it a try. AAK HYDRAULIC VALVES (679) 2023-09-25 https://www.aakindustry.com/info , -detail/pressure-reducing-relieving-cartridge- , valve-aak679 Contact:
Phone: Fax: Email: AAK INDUSTRY CO., LTD
Bona Business Building, No. 456 Taikang Middle Road Ningbo 315100 China 10/5/23 3:37 GMT
AAK Hydraulic Check Valve 3 major guarantees, waiting for Diego's big order
Diego comes from Argentina and specializes in drilling hydraulic machinery. All the hydraulic valves he used are purchased from China and the United States, whether they are hydraulic cartridge valves or hydraulic modular valves. A while ago, he stumbled when purchasing a hydraulic check valve that imitates SUN standard parts from a hydraulic valve manufacturer in Ningbo China. During equipment debugging, it was found that the opening pressure control of the hydraulic check valve in the system was unstable. The original manufacturer of the hydraulic check valve stated that this parameter is based on the SUN standard parts, and to fully match the equipment's operating conditions, it can only be optimized on the original standard parts. However, for the quantity is small, the manufacturer is not willing to do this customization. Diego is embarrassed. Diego contacted AAK hydraulic valve. After communication, it was learned that the hydraulic check valve he purchased encountered difficulties with unstable opening pressure control. Based on the working conditions of his equipment, we have determined that the hydraulic check valve equivalent to the original SUN standard component model can be used, and only a little more effort is needed on the hydraulic check valve spring. The unstable opening pressure control of the original manufacturer's hydraulic check valve is rooted in the inadequate spring and machining accuracy. Diego was a bit skeptical. I suggested him trying 10 hydraulic check valve samples of AAK first. If the test runs smoothly, then he can purchase hydraulic check valves in bulk. 3 weeks after AAK hydraulic check valves were sent out, Diego emailed us saying that their equipment was equipped with AAK hydraulic check valves, and the equipment was debugged and passed the testing. The opening pressure control of the AAK hydraulic check valve was stable, and there was no any problem. Their batch order for hydraulic check valves will be sent to AAK in 1 month, but the price needs to be renegotiated because the regular order quantity of hydraulic check valves will be more than 30 times that of the trial order. The reason why AAK hydraulic check valve can replace the one produced by the original cartridge valve manufacturer is because we do not copy industry standards. Whether in terms of material or component selection, it corresponds to the operating conditions of the equipment. 1. Selection of spare parts: The AAK hydraulic check valve adopts American Associated Spring, which has better sensitivity than SUN standard parts, especially the elastic limit and strength limit, far exceeding the domestic carbon spring steel wire. Our spring stability is a powerful guarantee for stable opening pressure. 2. Equipment selection: AAK hydraulic check valve adopts German machine tools, DMG high-precision CNC machining center, and testing equipment from Mitutoyo in Japan. The machining accuracy is also guaranteed. 3. Material selection: The AAK hydraulic check valve is made of corrosion- resistant alloy steel, which adds another guarantee to its durability. AAK hydraulic check valve has 3 major guarantees, not only with stable pressure control, but also with durability. You can also give it a try! AAK HYDRAULIC VALVES (580) 2023-05-09 https://www.aakindustry.com/info , -detail/check-valve-aak580 Contact:
Phone: Fax: Email: AAK INDUSTRY CO., LTD
Bona Business Building, No. 456 Taikang Middle Road Ningbo 315100 China 10/5/23 3:36 GMT
AAK Hydraulic Counterbalance Valves Benchmarked with SUN Hydraulics
Last week, the German customer Thorsten sent an order for 1,200 hydraulic counterbalance valves, and said that only AAK and SUN hydraulic counterbalance valves passed 1 million durability tests among the 6 hydraulic valve manufacturers making the samples. However, the price of AAK was 30% lower than that of SUN, and the delivery time was faster. In May this year, Thorsten’s company received an order for a batch of special hydraulic winches. The customer requested that the equipment be guaranteed for at least 1 year of service life. The engineer required that the durability test of the hydraulic counterbalance valve to be purchased by Thorsten must reach more than 1 million times. Thorsten found a local hydraulic counterbalance valve manufacturer to carry out the test. After 100,000 times, the O-ring wear affected the seal. After the sealing ring was replaced, the valve spool and valve body were worn and leaked again after 200,000 times, and the local manufacturer surrendered. Thorsten had to find a manufacturer of hydraulic counterbalance valves with higher durability. In order to avoid wasting purchasing time again, the two schemes were carried out simultaneously. One is to purchase the original SUN hydraulic counterbalance valves, and the other is to find a factory for customized hydraulic cartridge valves. When Thorsten contacted AAK, I told him that the requirement of hydraulic counterbalance valves for 1 million times was not very high. How could local hydraulic valve manufacturer fail? Thorsten said that when testing this hydraulic counterbalance valve, the opening and closing cycle time is set to 5 seconds, the set pressure is 21 PMa, and the flow rate is 9L/min. The wear resistance of the sealing ring, valve spool and valve body is at least 50% higher than that of the conventional hydraulic counterbalance valves. This time, including AAK, there are 6 hydraulic valve manufacturers to make samples. More than a month later, Thorsten said that among the 6 hydraulic counterbalance valve manufacturers, only AAK and SUN hydraulic counterbalance valves have passed the durability test for 1 million times, but the price of AAK is 30% lower than that of SUN. At the same time, AAK can provide a delivery time 4 weeks faster than that of sun. Thorsten especially wants to know why AAK is so strong. AAK hydraulic counterbalance valves are different from peers due to the following 3 points: 1. AAK adopts Japanese special polyurethane rubber sealing ring for this hydraulic counterbalance valve. Under the special working condition required by Thorsten, the durability limit of rubber sealing ring is about 100,000 times only, while the wear-resistant and high-pressure resistance performance of ours is more than twice that of other rubber sealing rings. 2.The 20CrNi2MoV high carburizing bearing steel imported from Germany adopted by AAK, combined with the carburizing pretreatment process and through the secondary quenching + cryogenic treatment + low temperature tempering process, has a microhardness of 237-247HV, and its wear resistance and contact fatigue performance have been improved by more than 3 times. Most hydraulic counterbalance valve manufacturers can not master the key of heat treatment even if they choose this steel. 3.AAK has its own durability test equipment independently developed, combined with NFPA/T2.6.1 standard, each hydraulic counterbalance valve is tested and meets the standard. AAK hydraulic counterbalance valves, benchmarked with SUN, you can also try a small order! https://www.aakindustry.com/info-det , ail/hydraulic-counterbalance-valves-aak322 Contact:
Phone: Fax: Email: AAK INDUSTRY CO., LTD
Bona Business Building, No. 456 Taikang Middle Road Ningbo 315100 China 10/5/23 3:35 GMT
Dual Function AAK Hydraulic Cartridge Relief Valve, helped Heller Save Cost
AAK used 3 methods to directly replace a cartridge check valve and a relief valve in the hydraulic system with one hydraulic cartridge relief valve, which not only facilitated installation, but also integrated the functions of the two valves. The manufacturing cost of the hydraulic unit was reduced by 6%, and helped Heller win the order from customer successfully. Heller is from Indonesia. In the second half of last year, their old customer customized a hydraulic power unit. The hydraulic cartridge relief valve used was produced by a cartridge valve manufacturer who has cooperated with them for 5 years. The equipment was successfully debugged, and the customer recognized it after trial use. However, after comparing with the market, the customer asked for a 5% reduction in the price of the equipment. Heller tried to reduce the purchase cost, but failed. Their engineers said that they could only optimize the hydraulic manifold to reduce the cost, but it was too late. The order has been holded for 2 weeks, and Heller was worried. Heller found AAK on Google and stayed on AAK hydraulic valve website for more than 10 minutes. Perhaps the customer cases of optimizing hydraulic cartridge valves stimulated him. He sent an email asking: How long does it take to optimize the original hydraulic manifold and sample? After communication, I learned Heller's dilemma. According to the schematic diagram of his power unit system, AAK engineers found that it was not necessary to adjust the original hydraulic manifold. There were 2 types of valves (check valve and relief valve) in the hydrostatic circuit of the system. If the functions of the 2 types of cartridge valves were integrated, the cost can be saved, and there would be no need for big change for the hydraulic manifold. Heller sent the sample order of hydraulic cartridge relief valve on the 3rd day after learning about the AAK scheme. After 50 days, AAK sent 3 hydraulic cartridge relief valve samples. 3 weeks later, Heller emailed that the commissioning of the dual function AAK hydraulic cartridge relief valve was smooth, and the overall purchase cost was reduced by 6%. Not only did they solve the pending order for the equipment, but their company's profits were also increased. The mind of AAK engineers benefited from more than 10 years of training in German HAWE. AAK achieved a dual function hydraulic cartridge relief valve with 3 skills. 1. This hydraulic cartridge relief valve is equipped with 3 separate fluid channels, which are respectively connected with the high pressure pipeline fluid, the low pressure side fluid and the feeding pressure pipeline fluid in the system. 2. The damper is added to strengthen the positive damping of the overflow function and realize reasonable control of the flow direction, which can replace the cartridge check valve function. 3. Connect the first and second lifting valve spools with a spring, and use the spring and lifting valve spool to make the fluid flow through the specified route as required to realize the dual functions of check and overflow. AAK hydraulic cartridge relief valve, integrating 2 functions into 1, you can also try a small order! https://www.aakindustry.com/info-det , ail/cartridge-relief-valves-aak424 Contact:
Phone: Fax: Email: AAK INDUSTRY CO., LTD
Bona Business Building, No. 456 Taikang Middle Road Ningbo 315100 China 10/5/23 3:35 GMT
AAK Hydraulic Flow Control Cartridge Valve 3 Advantages
Bront, from Israel, has been in contact with AAK for 3 years, but has not placed an order yet. During this period, there are inquiries about hydraulic cartridge valves, valve blocks and hydraulic manifolds. Although I marveled at the difficulty of doing business with this Israeli customer, I replied to his email in time. Sometimes, Surprise comes and catches you off guard. Bront placed a large order for 950 hydraulic flow control cartridge valves during the period of our CNY holiday. I remember that this hydraulic flow control cartridge valve was inquired in May 2021. At the end of 2021, I was suddenly asked to provide 3 samples. This is the valve benchmarking HydraForce, and we have the stock. We sent the hydraulic flow control cartridge valves directly to him the next day, and then there was no further news from him, until this order was placed, which was more than 1 year from last contact. After communication, it was learned that he was fooled by 2 cartridge valve manufacturers in Ningbo 3 years ago, so he was very cautious about the cartridge valve manufacturers from Ningbo. It can be seen that not only the weak teammates hurt the mood, but also the weak peers hurt the order. Bront told me that each parameter of AAK hydraulic flow control cartridge valve is benchmarking HydraForce, and its function also meets the requirements of their equipment. What worries him most is whether the performance can meet the requirements of the Israeli market. There is no repair in 1 year, no minor repair in 2 years, and no major repair in 3 years. Now 1 year has passed, and AAK hydraulic flow control cartridge valve is normal. It has proved that it has passed the threshold of "no repair in 1 year". Sometimes, without too much language, time is the best answer. I believe that this difficult Israeli customer has been settled by AAK. With our manufacturing quality, stable function and long performance, we impressed him. In the future, I will not worry about his order for cartridge valves. AAK hydraulic flow control cartridge valve is benchmarking HydaForce, but the price is only 70% of HydraForce, or even lower. Compared with domestic peers, AAK hydraulic flow control cartridge valve may be 20% more expensive, but the service life is twice that of its peers. AAK hydraulic flow control cartridge valve, insists on 3 points: manufacturing quality, function and performance. 1. In terms of material selection, AAK adopts 20CrNi2MoV high carburized bearing steel imported from Germany, combined with carburizing pretreatment process, through secondary quenching + cryogenic treatment + low temperature tempering process, cooled to 650~700 ℃, and then discharged after cooling to 450~500 ℃. The microhardness of the treated material is 237~247 HV, and its wear resistance and contact fatigue properties are more than 3 times higher than that of the ordinary material. 2. The equipment is equipped with a precision honing machine imported from the United States. The accuracy of the hydraulic flow control cartridge valve hole is guaranteed. The accuracy of the IT7~4 level and the surface roughness can reach Ra0.32~0.04 μm. It is difficult to find 5 cartridge valve manufacturers like this in Ningbo. 3. In terms of inspection, AAK hydraulic flow control cartridge valve is 100% fully inspected. The self-developed high-pressure test bench and durability test equipment are used to check the pressure, flow and fatigue resistance of the cartridge valves. AAK hydraulic flow control cartridge valve, 3 advantages, and its service life is twice that of its peers. You can also try it! https://www.aakindustry.com/info-detail , /flow-control-cartridge-valves-aak496 Contact:
Phone: Fax: Email: AAK INDUSTRY CO., LTD
Bona Business Building, No. 456 Taikang Middle Road Ningbo 315100 China 10/5/23 3:34 GMT
AAK Hydraulic Flow Control Valves, Fast Delivery, Zero Defects
At the end of last year, Stefan from Italy sent an email asking whether 50 non- standard hydraulic flow control valves could be produced within 25 days? For urgent orders like this, there is probably a problem with procurement. We have 3 years of cooperation with Stefan in some high-precision hydraulic flow control valves. Stefan is also an experienced purchaser in the hydraulic valve industry. Unexpectedly, he encountered problems on purchasing this time. In the second half of last year, their company produced a batch of hydraulic winches, which needed hydraulic flow control valves. We also received an inquiry for this hydraulic flow control valve but did not get the order. Stefan frankly advised that AAK quotation was about 20% higher than that of other hydraulic flow control valves, so I gave it up, and told him that although AAK quotation was 20% more expensive than that of the peers, the service life of AAK hydraulic flow control valves was twice as long as theirs. Stefan didn't expect that 3 months after the equipment was sold, some customers complained that the hydraulic winch was unable to operate. The after-sales personnel found that it was caused by the leakage of the hydraulic flow control valve. The customer asked to solve the abnormal equipment problem within 1 month. The original manufacturer of the hydraulic flow control valves advised that it should be the leakage caused by the wear of individual parts due to the poor accuracy. He is also willing to offer free replacements. Because this hydraulic flow control valve is customized and there is no inventory, and it takes 50 days to re-produce. Stefan has a big headache. He tried to contact other manufacturers of hydraulic flow control valves. They either rejected due to the small quantity or said that it would not be completed in 25 days. After the boss learned about these conditions, he asked Stefan to contact AAK again. Even if the price is higher, it can be completed within 25 days, moreover, there is no need to worry about the manufacturing quality of AAK hydraulic flow control valves. I told Stefan that as long as our production line can be adjusted, AAK will still maintain the original quotation of last year. After 25 days, AAK sent 50 hydraulic flow control valves, and Stefan finally relaxed. Yesterday, Stefan sent an e-mail to express his thanks. After AAK hydraulic flow control valves were installed on the equipment, and there has been no complaint for 6 months. His boss wants to know how AAK produces hydraulic flow control valves in half the time of its peers? 1. In terms of component processing, the hydraulic flow control valve adopts Japan OKK ultra precision machine tool, especially its nano resolution numerical control system, which can ensure that the component processing accuracy can reach 0.01-0.3μm. The shape and profile accuracy is 0.003 - 0.1μm. At the same time, the fast moving speed of each shaft reaches 60m/min, which is more than 30% faster than the production efficiency of other machine tools. At the same time, under the operation of our technicians, the processed components are free of defects. 2. In the assembly, considering the accuracy difference of each component of the hydraulic flow control valve, our peers use the matching method to assemble, while AAK uses the unified assembly method, and the assembly efficiency is twice that of the peers. 3. In terms of production deployment, for special orders, we can operate 24H, and there is flexible production line deployment. AAK hydraulic flow control valves, fast delivery, zero defects, you can also try a small order! https://www.aakindustry.com/info-det , ail/hydraulic-flow-control-valves-aak321 Contact:
Phone: Fax: Email: AAK INDUSTRY CO., LTD
Bona Business Building, No. 456 Taikang Middle Road Ningbo 315100 China 10/5/23 3:33 GMT
AAK Hydraulic Manifold Manufacturer 3 times of return to zero
15 years ago, I left my original company and started a business with a friend to establish AAK, a hydraulic cartridge valve manufacturer. Since that day, no one has paid me any more. From the first day of entrepreneurship, I stood on the edge of a cliff, facing the unknown mist, and could only grit my teeth and start moving forward. Ahead, there may be a new continent flowing with milk and honey, or a bottomless abyss. Zero for the first time in life. There are only expenses and no income in the bank card. I told my parents: I resigned and plan to start a business. I used to send you a lot of money, and you can use it as you please, but starting from this month, I can't give you the money. Give me 1 year, and after that, I will send you the money again every month. 3 years later, I found that the majority of Chinese hydraulic valve manufacturers are only concentrated in the domestic market and only replicate and produce according to the original sample. But these Chinese hydraulic valve manufacturers are not worried about orders, they have a comfortable life, only the payment is slow. If hydraulic valve manufacturer AAK follows the approach of its peers, it would be at best just a processing plant. Following the old map, no new continent can be found. It's time to change and return to zero. A glass is filled with water, and if we continue to pour it in, the water will overflow. Zeroing is not letting one's cup overflow, but rather constantly pouring, giving oneself space to accept new things. So, hydraulic valve manufacturer AAK gave up the domestic market and began to focus on the overseas market of hydraulic valves, marking zero in life for the second time. Business is like life, we should learn to forget our past achievements, let go of our so-called self-esteem, put ourselves to the lowest level, and be brave enough to try. The more confident you are in the future, the more patient you will be in the present. But many Chinese hydraulic valve manufacturers do not realize that they are already in an industrial comfort zone. Returning to zero means daring to shed one's shell. The outer shell is tangible and easy to break. The inner shell is intangible and difficult to break. The ability to break the shell in one's heart determines the ceiling of growth. Many people live their entire lives in a 'shell' and are unwilling to see the truth. Life is like a bicycle, only by constantly moving forward can one not fall. Choosing 'molting' and 'returning to zero' is like adding a booster to this bicycle to make it move faster. 8 years ago, I saw and started to choose overseas markets. I realized that it was time to evolve AAK's products. With the Chinese hydraulic manifold manufacturer in plan and were ready to return to zero for the third time. Until now, it has been running for 8 years and continues to serve Honeywell, a Fortune 500 company. Hydraulic valve manufacturer AAK, spent 3 years from supplying domestic listed companies to focusing on overseas trade. From a Chinese hydraulic valve manufacturer to a Chinese hydraulic manifold manufacturer, it took 5 years. Most Chinese hydraulic manifold manufacturers always feel that they are doing well domestically, but they cannot see the changes in overseas markets and are not aware of the crisis in the industry. Chinese hydraulic manifold manufacturer AAK, has returned to zero 3 times, and returned 3 times, continuously serving the Fortune 500 company. AAK HYDRAULIC VALVES (678) 2023-09-24 https://www.aakindustry.com/info , -detail/hydraulic-manifold-manufacturers-aak678 Contact:
Phone: Fax: Email: AAK INDUSTRY CO., LTD
Bona Business Building, No. 456 Taikang Middle Road Ningbo 315100 China 9/28/23 2:37 GMT
AAK Hydraulic Cartridge Valves Supplied to 7 world top 500 enterprises
Today, the American customer April has placed another new order for hydraulic cartridge valves. Coincidentally, this PO is for 100 non-standard customized hydraulic cartridge valves that AAK has cooperated with them for 10 years. April is the first customer of AAK Hydraulic Valve to enter the overseas market, and also the first foreign trade order of AAK Hydraulic Valve 3 years after its establishment. Up to now, AAK hydraulic cartridge valves have been supplied to 7 world top 500 enterprises. AAK hydraulic cartridge valves adhere to 3 points, adhere to the manufacturing quality of hydraulic cartridge valves, pay attention to research and development, and focus on innovation. In particular, the high-precision and high-performance hydraulic cartridge valve samples have been defeated repeatedly, but we never give up until success. April's first inquiry is for hydraulic cartridge valves used in the military industry, with an accuracy of 0.8μm or less, the durability of more than 1 million times, and the opening and closing performance of 1 second. Our engineer was a little timid when he saw these requirements. I told him that if the development was successful, all the credit would go to him. If it failed, I would pay for it. 2 months later, the samples of AAK hydraulic cartridge valve was sent out. 2 weeks later, April reported that the opening and closing performance of AAK hydraulic cartridge valves reached the standard, but the accuracy and durability tests failed. This indicates that the material selection is incorrect and the process is correct. I told April that AAK was confident that the samples would be successful. 3 months later, the test of AAK hydraulic cartridge valves still failed, and the durability was barely 800,000 times. I encouraged the engineer to continue the test. 5 months later, the AAK hydraulic cartridge valve was approved by April. At the same time, the never say die spirit of AAK also makes April admire, because AAK is the only manufacturer of hydraulic cartridge valves that insists on testing samples in 1 year and does not give up. AAK hydraulic cartridge valves, in the face of failure, the wealth gained is that after every failure, there is an increase in technology accumulation, of which the most critical is 3 points: 1. Equipment updating is not stopped, and fixture innovation should be synchronized. 5 years ago, the precision honing machine imported from the United States was introduced. The accuracy of valve holes processed by other hydraulic cartridge valve manufacturers is 0.8μm--1.0μm, while with AAK synchronous innovation fixture, the valve hole accuracy can be within 0.6μm- -0.8μm, which is 20% higher. 2. Material types: AAK material warehouse has 12 kinds of special steels, such as 3Cr3Mo3W2V hot work die steel, 20CrNi2MoV high-permeability carbon bearing steel imported from Germany, Hastelloy alloy steel imported from the United States etc. At the same time, there are 8 kinds of sealing ring materials. At any time, we can meet the requirements of customers with high quality hydraulic cartridge valves. 3. Technology and process upgrading: AAK has senior engineer from HAWE, and technical teams with an average of more than 15 years of industry experience, adhere to the manufacturing quality of hydraulic cartridge valves, pay attention to research and development, and focus on innovation. AAK hydraulic cartridge valves are supplied to 7 world top 500 enterprises. You can also try a small order! https://www.aakindustry.com/info-det , ail/hydraulic-cartridge-valves-aak320 Contact:
Phone: Fax: Email: AAK INDUSTRY CO., LTD
Bona Business Building, No. 456 Taikang Middle Road Ningbo 315100 China 9/28/23 2:37 GMT
AAK Hydraulic Pressure Reducing/Relieving Valve Benchmarking SUN PPDB
Today, AAK will post a Pilot-Operated, Pressure Reducing/Relieving Valve benchmarking SUN Hydraulics' PPDB series, and we have developed 3 sub categories: E-PPDB-LAN; E-PPDB-LDN; E-PPDB-LWN. The working characteristics of this pilot operated pressure reducing/relieving valve are: the pilot operated valves exhibit exceptionally flat pressure/flow characteristics are very stable and have low hysteresis. Pilot operated reducing/relieving valves by nature are not fast acting valves. For superior dynamic response, consider direct acting valves. The function of this pilot operated pressure reducing/relieving valve is to reduce a high primary pressure at the inlet (port 2) to a constant reduced pressure at port 1, with a full-flow relief function from port 1 to tank (port 3). In the past 12 months, AAK have received 8 inquiries and 6 orders. The selling points of this pilot operated pressure reducing/relieving valve are: 1. Control Pilot flow: 7 - 10 in³/min, Benchmarking SUN 2. The service life is 2 times that of domestic peers in China Technical parameters of AAK E-PPDB Hydraulic Pilot-operated, pressure reducing/relieving valve: Max. Operating Pressure: 350 bar (5000 psi) Capacity: 10 gpm (40L/min) Control Pilot Flow: 7 - 10 in³/min. Cavity: T-11A For this pilot-operated pressure reducing/relieving valve with 3 sub categories, benchmarking SUN PPDB series, you can also try it out. AAK HYDRAULIC VALVES (579) 2023-05-08 https://www.aakindustry.com/info , -detail/pressure-reducing-valve-aak579 Contact:
Phone: Fax: Email: AAK INDUSTRY CO., LTD
Bona Business Building, No. 456 Taikang Middle Road Ningbo 315100 China 9/28/23 2:36 GMT
AAK Hydraulic Relief Valves Opening and Closing in 1 second
Romero from Spain has cooperated with AAK on a hydraulic pressure control valve for 3 years, and it is re-ordered 3 times a year. He has been very smooth on every purchase, but in October last year, he encountered problem on a batch of hydraulic relief valves purchased from other hydraulic valve manufacturer, and was complained by customers one after another, which made the boss very disappointed with him. AAK finished the non-standard customized hydraulic relief valves with 1 second opening and closing performance within 30 days, which made Romero win back the trust of the boss. Not long after returning from the Spring Festival holiday this year, Romero emailed to ask whether 50 hydraulic relief valves with opening and closing ability of less than 1 second can be customized within 30 days, and stressed that the flow must be stable. Because the new year just started, there were many things in the workshop, and I wanted to refuse. After several rounds of email communication, I learned about his predicament. In the second half of last year, their company produced a batch of hydraulic power units for ship equipment. 3 months after sales, the customer complained that the pressure supply of the system was unstable. It was found that the opening and closing performance of the hydraulic relief valve was poor and the flow control was unstable, which led to the unstable pressure supply of the system. The original manufacturer of the hydraulic relief valves said that this is an individual phenomenon, and the hydraulic relief valves with problem can be replaced for free. But unexpectedly, in the next month, they received complaints from customers one after another, and can not get into contact with the original manufacturer, making their after-sales service hard to cope with. The boss was very angry and requested Romero to re-customize 50 hydraulic relief valves within 40 days, and the manufacturing quality must be excellent. Romero contacted several hydraulic relief valve manufacturers. They either can't make hydraulic relief valves with opening and closing performance less than 1 second, or they need 60 days to customize 50 hydraulic relief valves. A week has passed without any progress. Romero is extremely worried. In the past 3 years, I have enjoyed working with Romero. After discussing with the engineer, I decided to help him. After 30 days, AAK sent 50 hydraulic relief valves with opening and closing ability less than 1 second. Today, Romero informed that with the use of AAK hydraulic relief valves, their equipment has not been complained in nearly 6 months. Before installation, their engineers specially tested the opening and closing performance of AAK hydraulic relief valves, each within 1 second. I told Romero that our guarantee is not 6 months, but 12 months is our pass line. As long as there are no deliberate human problems, the service life of AAK hydraulic relief valve is 2 million times, which is benchmarked with the quality of HydraForce. This is also the reason why many hydraulic valve manufacturers can not do it. AAK has already surpassed its domestic counterparts. 1. The selection of the pressure spring of this hydraulic relief valve is the key. 60Si2CrVA alloy steel pressure spring is its perfect match. The tensile strength and yield strength of the pressure spring is at least 70% higher, ensuring the opening and closing performance within 1 second. 2. AAK uses the high-precision honing machine imported from Switzerland to finish this hydraulic relief valve, and the valve hole accuracy can be within 1.0μm, the flow stability is guaranteed, while most of the hydraulic relief valve manufacturers are around 2μm. 3. AAK hydraulic valve has a large amount of data storage. With the most advanced UG/SOLIDWORK software and finite element analysis method, the process data can be configured in 2 hours, which is 3-6 times faster than other hydraulic valve manufacturers. AAK hydraulic relief valves, opening and closing in 1 second, durable for 2 million times, you can also have a small try! https://www.aakindustry.com/info-detai , l/hydraulic-relief-valves-aak319 Contact:
Phone: Fax: Email: AAK INDUSTRY CO., LTD
Bona Business Building, No. 456 Taikang Middle Road Ningbo 315100 China SOURCE: Import-Export Bulletin Board (https://www.imexbb.com/)
© 1996-2024 IMEXBB.com. All rights reserved.
|
|