Automotive, Vehicles & Transportation - Others

Auto recloser relay control higher voltages or currents by using lower voltages or currents. When a certain voltage or current is applied to both ends of the electromagnetic relay coil, the magnetic flux generated by the coil passes through the magnetic circuit composed of the iron core, the yoke, the armature and the working air gap of the magnetic circuit. Under the action of the magnetic field, the armature is attracted to the pole face of the iron core. Therefore, the normally closed contact of the contact is pushed to be disconnected, and the normally open contact is closed. When the voltage or current at both ends of the coil is less than a certain value, and the mechanical reaction force is greater than the electromagnetic attraction force, the armature will return to the initial state, the normally open contact is disconnected and normally closed contact is on. How To Test Auto Relays？ (1) A simple method for judging the working performance of the relay. Turn on the ignition switch, and then use your ear or stethoscope to listen to the sound of the control relay, or feel the vibration of the relay with your hand. If there is vibration, then the relay is working well, the electrical appliance does not work due to other reasons. Otherwise, the relay is not working properly. You can also unplug the relay for testing, for example, if the air conditioner compressor does not work, you can start the engine, turn on the blower switch and the air conditioner switch. Then unplug the connector of the air conditioner compressor relay to judge. If the sound of the relay action can be heard, the engine speed drops significantly when the relay is unplugged, and the engine speed rises when the relay is inserted, it means that the air conditioner compressor relay and its control circuit are normal. (2) Common failures of relays. Common failure phenomena of relays include coil burnout, inter-turn short circuit or insulation aging, contact ablation, thermal decay, and inability to adjust the initial operating current. ①The relay coil is burnt out. In order to prevent this from happening, if the temperature may exceed 80°C during repair, maintenance and electric welding, the temperature-sensitive relays and electronic control units should be removed. ② Contact ablation. For example, vehicle with 491Q-ME engine, the relay of the air conditioner condenser fan is just below the glass cleaning spray pipe. If the spray pipe is broken, the cleaning fluid will leak to the relay, making the relay normally open contact is corroded and cannot be disconnected, which will lead to the failure of the air conditioner condenser fan to keep running. Therefore, water should be strictly prevented from entering the relay. (3) Try to reduce the contact resistance of the relay contact The contact resistance existing between the contacts of the automotive relay is mainly composed of shrinkage resistance and surface film resistance. The contact resistance of the contact is related to the contact form, material properties and surface processing of the contact. It can be seen that to reduce the contact resistance of the relay contacts, under the condition of a certain contact pressure, it can be started by improving the contact state and improving the contact material. (4) Poor grounding of the ECU may affect the normal operation of the relay As one of the most professional car spares suppliers, we provide automobile air filter, car spares and parts, auto off relay, auto power relay, auto relay block, auto relay switch, pencil coil, etc. For more information, please feel free to contact us!

Minimum Order: 1 bags

Sensor for automotive is the input device of automotive computer system. It converts information of various working conditions, such as vehicle speed, temperature of various media, engine operating conditions, etc., into electrical signals and sends them to the computer, so that the engine is in the best working state. As the information source of electric control system, automotive sensor is not only the key component of electric control system, but also one of the core contents in the field of automotive electric technology. Automobile sensors can measure and control various information such as temperature, pressure, position, speed, acceleration and vibration in real time and accurately. Automotive sensors from MAPMS have characteristics. Strong adaptability and resistance to harsh environment. It also has good sealing, moisture resistance, corrosion resistance and so on. Strong anti-interference ability. High stability and reliability. High cost performance, suitable for mass production. It converts various operating conditions of the automotive, such as vehicle speed, temperature of various media, engine operating conditions, etc., into electrical signals and sends them to the computer so that the engine is working at its best status. How Does The auto sensors Work? There are various sensors on vehicle. They constantly detect the working condition information of the vehicle, convert the electric energy into signals, and transmit these signals to the ECU in real time. After the ECU makes the corresponding decision and processing, then outputs the signal to the corresponding actuator. After receiving the output signal, the actuator performs the corresponding action to realize a certain predetermined function. Each sensor performs its duties and cooperates with each other, which plays an important role in the operation of the vehicle. Sensors used in the engine control system are the core of all auto sensor car, including temperature sensors, pressure sensors, position and speed sensors, air flow sensors, gas concentration sensors and knock sensors to help ECU can accurately control the working condition of the engine to improve the power of the engine, reduce fuel consumption, reduce exhaust emission and carry out fault detection. As one of the most professional auto spares suppliers, we provide industry auto parts, auto spares sale, etc. For car sensor cost or more information, please feel free to contact us!

Minimum Order: 1 bags

Automobile fuel supply system is classified according to fuel supply mode: carburetor engine, EFI engine and in cylinder direct injection engine, supply to the cylinders, and make it ignite, burn and expand to do work near the end of compression. Finally, the fuel supply system should also discharge the combustion product exhaust gas into the air. Each part must work flawlessly to achieve expected vehicle performance and reliability. Car fuel supply system has been widely used in automobiles because of its simple structure, convenient use and low cost. However, the main disadvantage of carburetor engine is that the inflation and mixture distribution are not ideal. It has a certain adverse impact on the improvement of engine power, economy and emission. Therefore, modern cars are basically not used. At present, the mainstream is EFI engine and in cylinder direct injection engine. EFI engine uses electronic control device to control the fuel supply process of the engine. According to the number of injectors, EFI engine can be divided into multi-point injection and single point injection. At present, multi-point injection is mostly used. The main principle of multipoint EFI is that the injection process of gasoline fuel is in the intake manifold. If the injector is installed on the intake pipe of each cylinder, gasoline can be injected into multiple cylinders, which forms multipoint injection. The cost of gasoline injection is not only lower, but also less carbon deposition. How Does The Automotive Fuel System Parts Work? The fuel pump sucks the fuel out of the fuel tank, filters out the impurities through the fuel filters and enters the low-pressure fuel chamber of the fuel injection pump. After increasing the fuel pressure, fuel will be transmitted to the fuel injector through the high-pressure fuel pipe. When the fuel pressure reaches a certain value, the fuel injector sprays the fuel into the combustion chamber in the form of mist to form mixed gas and burn. After working, the waste gas will be discharged into the atmosphere through the exhaust device. The task of fuel supply system is to prepare a certain amount and concentration of combustible mixture according to the requirements of various working conditions of the fuel engine, supply it to the cylinder, and make it ignite, burn and expand to do work near the end of compression. Finally, the supply system should also discharge the combustion product - exhaust gas into the atmosphere. How To Wire Automobile Fuel System Parts? Components of automotive fuel supply system consist of fuel tank, fuel pipe, fuel pump, fuel filter, air filter, fuel pressure regulator, fuel injector, intake manifold, exhaust manifold, etc. The task of the fuel supply system of fuel engine is to pump the fuel out of the fuel tank through the fuel pump, via fuel filter which filters the impurities and water in the fuel, then enters the fabricated fuel rail. The engine ECU sends fuel injection signals to the fuel injection nozzle according to the output signals of various sensors of the engine, ejects the fuel from the fuel injectors at a certain pressure, mixes it with the clean air obtained through the air filter in the intake manifold in a certain proportion according to the requirements of various working conditions of the engine, finally enters the cylinder, compresses, works and exhausts in the cylinder, to generate engine power. As one of the most professional car spares suppliers, we provide industry auto parts, auto spares sale, etc. For more information, please feel free to contact us!

Minimum Order: 1 bags

The car air filter commonly used in passenger fuel vehicle engines mainly have paper air filter and polyurethane air filter. Paper air filters are made of microporous filter paper treated with resin. The filter paper is porous, loose and folded. They have certain mechanical strength and water resistance with advantages of high filtration efficiency, simple structure, light weight, low cost and convenient maintenance. They are most widely used as vehicle air filters at present. Polyurethane car filter are made of soft, porous and spongy polyurethane with strong adsorption capacity. They have the same advantages of paper air filters, but also have low mechanical strength. What Are the Symptoms of a Bad Air Filters? The auto air filters is a device for removing particulate impurities in the air. If the air contains dust and other impurities, will aggravate the wear of engine parts, so air filter with good performance must be installed into the vehicle. The main requirements of the air filter are high filtration efficiency, low flow resistance and continuous use for a long time without frequent maintenance. In case of damage or blockage, the following phenomena will occur. Acceleration performance decreases and fuel consumption increases. Once the filter element is blocked, there is too much dust and the aperture of the filter paper is blocked, will hinder the passage of air. Then the air intake rate will decrease, the air flow will decrease, and there is not enough air support when the engine burns. Even if the accelerator is pressed deeply, the speed still can not come up, there will be insufficient power and the driving fuel consumption will increase. Moreover, under the strong negative pressure (intake suction) of the engine, the dust, impurities and particles outside the filter element will break through the filter paper and directly enter the cylinder to participate in combustion, even lead to the breakage and rupture of the filter paper. The engine emits black smoke. If the automobile air filter is damaged or not replaced and cleaned for a long time, the dust will directly enter the engine and pass through the throttle. At this time, the particles in the air are like grinding sand, which will cause wear to the throttle. After the throttle is worn, it will sink, reduce the compression ratio and air leakage, resulting in the reduction of engine cylinder pressure, hard to start and low combustion efficiency. The cylinder burns insufficiently, the exhaust pipe emits black smoke and presents a divergent shape, and the air flow has no impulse. As one of the most professional car spares suppliers, we provide automobile air filter, auto spares sale, pencil coil, etc. For air filter car cost or more information, please feel free to contact us!

Minimum Order: 1 bags

Car air conditioning system is a device that realizes cooling, heating, ventilation and air purification of the air in the vehicle. It can provide a comfortable driving environment for driver and passengers, especially reduce the driver's fatigue strength, and improve driving safety. The air conditioning unit has become one of the indicators to measure whether the vehicle is fully functional. Modern vehicle air conditioners have four functions, any of which are designed to make driver and passengers comfortable. The air conditioner can control the temperature in the cabin, both heating and cooling the air, to make the cabin has comfortable temperature. The air conditioner can discharge the moisture in the air. Dry air absorbs human sweat and creat a more comfortable environment. The air conditioner has functions of inhale fresh air and ventilation. The air conditioner can filter the air to remove dust and pollen. How Does The Air Conditioning System (A/C) Work? Automotive air conditioning is mainly composed of refrigeration system, heating system, ventilation and air purification system and control system. The principle of automotive air conditioning has four sections. A, The compressor sucks the low-temperature and low-pressure refrigerant gas at the outlet of the evaporator, and compresses it into high-temperature and high-pressure gas and discharges from compressor. B, The high-temperature and high-pressure refrigerant gas enters the condenser and condenses into a liquid, discharges a large amount of heat. C, The refrigerant liquid with high temperature and high pressure increases in volume after passing through the expansion device, the pressure and temperature drop sharply, then discharged from the expansion device in the form of a mist. D, The mist-like refrigerant liquid entering the evaporator, the boiling point of the refrigerant is much lower than the temperature in the evaporator, and the refrigerant liquid evaporates into a gas. Diagram of Air Conditioning System (A/C) The automotive air conditioning refrigeration system consists of a compressor, a condenser, a liquid receiver dryer, an expansion valve, an evaporator and a blower. The components are connected by copper pipes and high-pressure rubber pipes to form a closed system. When the refrigeration system works, the refrigerant circulates in this closed system in different states. As one of the most professional auto spares suppliers, we provide car air conditioner replacement, car air conditioner gas, car ac unit, car ignition components, car auto spare parts, etc. For car ac unit price or more information, please feel free to contact us!

Minimum Order: 1 bags

The airbag sensor is the input device of control signal in the SRS system. When the vehicle happens to collides, the airbag sensor detects the intensity signal of the vehicle collision, and inputs the signal into the airbag computer. The airbag computer determines whether to detonate the inflatable element to inflate the airbag according to the signal of the airbag crash sensor. How To Test airbag front sensor? 1) Symptoms of airbag system failure are difficult to diagnose, so diagnostic codes are the most important source of information for troubleshooting. Always check the diagnostic codes before disconnecting the battery. 2) Disconnect the ignition switch during inspection. If the vehicle allows to remove the negative electrode of the battery, it is better to disconnect the power supply. It should be started after removing the negative electrode for 90s or longer. Because the airbag system is equipped with a backup power supply, the airbag may still deploy within 90 seconds after removing the negative terminal of the battery. 3) Even if only a minor collision occurs and the airbags are not deployed, the front airbag pressure sensor and steering wheel cushion should be checked. 4) Do not expose the front airbag impact sensor, center airbag sensor assembly and steering wheel pad directly to hot air and flames. 5) When testing the circuit, a high-impedance multimeter should be used for measurement. 6) The parts of the airbag are attached with instruction labels, and the listed precautions should be strictly followed during operation. 7) After pulling out the airbag wiring plug, use a small copper wire to short the airbag connector. 8) Do not measure the resistance of the detonator tube of the airbag inflation element, so as not to cause the airbag system to explode by mistake. The method of decomposing the inspection parts should be adopted first, and then searching step by step. 9) The airbag system is a very sensitive device. A little carelessness during inspection may detonate the airbag and cause unnecessary losses. 10)The wire harness and connector of the airbag system are generally covered with a special color sleeve, which is different from other system wire harnesses. Do not damage these bushings during inspection. As a professional auto spare parts supplier, we provide car ignition components, car ignition coil, etc. For impact sensor price or more information, please feel free to contact us!

Minimum Order: 1 bags

The airbag clockspring is a piece of wire harness that connects the main airbag to the airbag harness. Since the main airbag needs to rotate with the steering wheel, when the steering wheel is turned left or right, the wire harness cannot be pulled off, so the connecting wire harness must be left with a margin, and it is necessary to ensure that the steering wheel is turned to the limit position to one side without being pulled off. Key Features of Airbag Clockspring  An important part of connecting the electrical appliances between on the steering wheel and steering column. Can be rotated infinitely. Connect the main airbag to the airbag harness. How To Test Airbag Clockspring？ If the horn does not sound, first unplug the horn, connect the test light, press the steering wheel. The test light does not turn on, check the fuse and relay, if the relay does not respond when pressed, remove the airbag, and directly put the horn button wire is grounded. If the horn sounds, ground the horn wire above the airbag clockpring. If the horn does not sound, check the airbag clockpring, and use a multimeter to measure the continuity of the wire. The airbag light is on. Under the computer test, if it shows that the driver's airbag is disconnected, remove the airbag. If the wiring harness is well, unplug the main airbag and use a 2 ohm resistor to put it into the airbag tap. Clear the fault code. If it can be cleared, it means that the airbag is faulty. It cannot be cleared. Pull the airbag clue below the clockspring wire, connect the 2 ohm resistor, and clear the fault code. If it can be cleared, the clockspring is broken. If it cannot be cleared, check the wiring harness from airbag computer to clockspring. The audio control buttons are generally not broken, the faulty probability is very low, have the same inspection steps. About abnormal noise. You can remove the clockspring and test the vehicle again. It must be replaced it if there is no abnormal noise after removing it. As a professional auto spare parts company, we provide clock spring on steering wheel, clock spring triton, car ignition components, clock spring steering wheel, auto ignition coil, etc. For clock spring price or more information, please feel free to contact us!

Minimum Order: 1 bags

OKA PP Clutch GEN-II TOYOTA 1 FZ 185mm TO-185044SPR Double Plate Clutch Kit With Flywheel 45# Steel for GEN-II TOYOTA 1FZ Double Plate Clutch 185mm / Flywheel 45# Steel Super condition and capable of holding big power. This is a PUSH type clutch, please check compatibility….

Forged Steel AISI 4140 Gear Hobbing Doubel Helical Gear Wheel-Double Helical Gears 1) Features of Double Helical Gears a) Double Helcial gear opposite thrust reactions thus cancel out the thrust force within the gear itself. b) The net axial force that acts on the bearings is zero. c) Power transmitting capacity is very high. d) By using this high pitch line velocities can be attained. 2) Description of double helical gear Double helical gear with both left hand and right hand helical teeth. The double helical form balances the inherent thrust froces.

GT15 454159-5002S 038145701A 038145701AX 038145701AV 038145701D turbocharger for AGR/TDI 90 engine Size: 39*31*40cm Turbo Model: GT15 Condition: New Type: Turbo charger Automobile manufacturing: car Application: 1996-98 Audi A3 1.9 TDI (8L) Engine AGR 1997-00 Skoda Octavia I 1.9 TDI Engine AGR 1997-01 Volkswagen Bora 1.9 TDI Engine AGR 1997-01 Volkswagen Golf IV 1.9 TDI Engine AGR Product Details Generally speaking,turbocharging is a great idea.it's a smaller engine,but you're still getting a decent amount amount of power,"says Mike Quincy,autos editor at Consumer Reports."The idea with a smaller engine,especially a four- cylinder,is that you're going to get decent fuel economy without giving up power, APPLICATIONS 1996-98 Audi A3 1.9 TDI (8L) Engine AGR 1997-00 Skoda Octavia I 1.9 TDI Engine AGR 1997-01 Volkswagen Bora 1.9 TDI Engine AGR 1997-01 Volkswagen Golf IV 1.9 TDI Engine AGR

Reefer containers necessitate a higher level of manufacturing technique for refrigerated container manufacturers, and only five factories in the world are capable of producing large scale RF containers, with the majority of them based in China. DFIC owns two reefer factories that produce high- quality reefer shipping containers through long-term automation technology investment and development. Refrigerated shipping container dimensions The common reefer container dimension is 20ft and 40 ft. The external length of 20ft reefer container is 20ft, width is 8ft and height is 8ft6. The external length of 40ft reefer container is 40ft, width is 8ft and height 9tf 6. Size & TYPE External(mm) Internal(mm) Weights (Kg) Cubic Capacity（M³) Length Width Height Length Width Height Max Gross Weight Tare Weight Max Payload 20'RF Reefer Container 6,058 2,438 2,591 5,456 2,290 2,276 30,480 2,810 27,670 28.4 20'RH Reefer Container 6,058 2,438 2,896 5,456 2,290 2,581 30,480 2,920 27,560 32.2 40'RF Reefer Container 12,192 2,438 2,591 11,588 2,290 2,253 30,480 5,020 25,460 59.8 40'RH Reefer Container 12,192 2,438 2,896 11,590 2,290 2,558 34,000 4,480 29,520 67.9 WHAT IS A REEFER CONTAINER CARRIER A reefer container is a type of ship carrying containers that keeps its cargo cool and regulated. Reefers are necessary for fresh food such as fruit, meat, fish, vegetables, dairy, as well as non-food items such as flowers and pharmaceuticals. Reefer container operations are often conducted on vessel or shore power during shipping. A generator supplies portable power to the reefers during rail or truck transport, the air freight versions are intended to maintain temperature for up to around 100 hours. REEFER CONTAINER MANUFACTURER DFIC Qingdao (DFQT) and Qidong (DFQD) factories own the most updated technology and working spaces to manufacture reefer cargo containers. DFQT reefer production line covers 2.9 million square feet, and DFQD factory reefer line covers 1 million square feet. A high-quality container reefer unit not only depends on the manufacture craft but also the quality of chemical foaming, cooling machine, and the way of using. Therefore, DFIC will control each process during production to ensure cargo won’t be ruined during the travel. REEFER CONTAINER PRICE There are more various and complicated factors that affect refrigerated container price than that of dry freight container. The main factors include original material prices like Polyurethane, steel price, etc., and the government policy control may affect the production effectiveness, too. Therefore, the refrigerated container cost is unstable these days especially since the global pandemic is one of the biggest factors affecting the price. Please contact us if you want to know more about the types of reefer container and the reefer container details. DFIC provides side opening shipping container for sale, side opening container, pallet-wide container, reefer container, etc. For more information, please feel free to contact us!

DFIC manufacture high-quality open top container for hundreds of clients these years, and provide all kinds of logistics container solutions for container transportation internationally. Instead of steel roof, open top containers have an empty top covered by a tarp. This allows for the loading of oversized cargo such as timber and scrap metal from the top. Open top cargo containers, like closed containers, usually have end doors to allow for easier loading and unloading. OPEN TOP CONTAINER DIMENSION The common open top container sizes are 20ft and 40ft length, and similar height and wide with standard dry container. Size & TYPE External(mm) Internal(mm) Weights (Kg) Cubic Capacity（M³) Length Width Height Length Width Height Max Gross Weight Tare Weight Max Payload 20'FT Open Top Container 6,058 2,550 2,896 5,893 2,438 2,713 35,000 2,780 32,220 39.4 40'FT Open Top Container 12,192 2,438 2,591 12,032 2,352 2,341 30,480 4,640 25,840 66.3 WHAT IS AN OPEN TOP SHIPPING CONTAINER Unlike standard dry container with solid roof on top, open top storage containers have an open top covered by a tarpaulin. This allows for the loading of oversized cargo such as timber and scrap metal from the top. Flat rack open top containers, like closed containers, usually have end doors to allow for easier loading and unloading. OPEN TOP CONTAINER USES A container open from the top is used to transport cargo that is too tall, too long, or both. Packing and unpacking open top containers is simple with a crane or crab. Open top container high cube has end doors to allow for greater loading and unloading flexibility. Oversized cargo such as machinery, wood, steel, scrap metals, and so on. DFIC provides side opening shipping container for sale, side opening container, pallet-wide container, open top container for sale, 53 container, etc. For more information, please feel free to contact us!

DFIC manufactures high-quality open-sided containers. Open side storage container is a kind of ship carrying containers which have been modified to incorporate two sets of double doors into the long side of the container. This opens up the entire length of the container, giving full and unrestricted access. OPEN SIDE CONTAINER DIMENSIONS Size & TYPE External(mm) Internal(mm) Weights (Kg) Cubic Capacity（M³) Length Width Height Length Width Height Max Gross Weight Tare Weight Max Payload 20'FT Open Side Container 6,058 2,438 2,591 5,952 2,224 2,242 24,000 4,160 19,840 29.5 40'FT Open Side Container 12,192 2,438 2,896 12,032 2,290 2,651 30,480 4,460 26,020 73 WHAT IS OPEN SIDE CONTAINER High cube open side container have doors on the container's longer side. Unlike containers with only one pair of doors at the shorter end, these containers have two pairs of doors: normal doors along the width and specialized doors along the length. Because the side opening container has easier access and makes loading and unloading cargo much easier, the open side container is a great alternative to standard-sized containers. It is ideal for those who need to fill it with items that are too large to fit through standard container doors. OPEN SIDE SHIPPING CONTAINER PRICE Open side shipping container price has fluctuated like dry cargo container, which depends on the material price, government production control, and market demand. DFIC promises to provide high-quality storage container with side opening at the at the best price. Contact us to keep updated with the side opening shipping container price. DFIC provides side opening shipping container for sale, side opening container, pallet-wide container, open side shipping container for sale, etc. For more information, please feel free to contact us!

DFIC professionalize on manufacturing all kinds of flat-rack and convertible fact-rack container. Flat Rack Containers are a type of special purpose containers with walls only on the short end. Due to different dimensions or abnormal loads, these flat rack shipping containers are used when the cargo must be loaded from the top or sides such as cars, oversize machine and other special merchandises. FLAT RACK CONTAINER DIMENSION Flatracks container can be collapsible or non-collapsible, and they can have walls or not. Their measurements, however, remain roughly the same. The common flat rack container size includes 20ft and 40ft, and other special sizes can be customized by DFIC. Size & TYPE Internal Weights Cubic Capacity（M³) Length Width Height Tare Weight Max Payload 20'FT Flatrack Container 5.94m/19.5ft 2.35m/7.7ft 2.35m/7.7ft 2,360kg /5,203.8 lbs 30,140kg /66,458.7 lbs 32.7m³/1,154.3 cu ft 40'FT Flatrack Container 12.13m/39.8ft 2.35m/7.9ft 2.14m/7ft 40,000kg /88,200 lbs 40,000kg /88,200 lbs 62.2 m³/2,195.7 cu ft WHAT IS A FLAT RACK CONTAINER DFIC manufactured flat rack container for sale is typically used for the transport or storage of cargo with irregular dimensions. Flat racks only have sides on the short side of the container, known as the bulkheads, allowing the cargo to protrude from the side of the container during transportation. Flat rack high cube containers are typically available in two sizes: 20 feet and 40 feet. The choice is determined by the size of the cargo. Typically, the only difference between these two types is their length. FLAT RACK CONTAINER WEIGHT CAPACITY There is no limit to the flat rack container loading because they don't have side or top walls like regular dry container. Flat racks are used to transport oversized cargo such as breakbulk cargo, construction equipment, cranes, pipes, windmills, automobiles, steel, glass, sugarcane, and so forth. FLAT RACK SHIPPING CONTAINER PRICE Flat rack shipping container for sale has the most reasonable price and great quality, and is mainly manufactured in Shanghai, Qingdao, and Jinzhou. As different kinds of ship carrying containers, the flat-rack and convertible flat rack prices will be different since the material and cost are different. For more flat rack container price information, please consult with our sales. DFIC provides side opening shipping container for sale, side opening container, pallet-wide container, etc. For more information, please feel free to contact us!