Telecommunications & Networks - Others

Description JMY6202 is a series of RFID read/write module with UART, USB HID and IIC communication port. It has various functions and supports multi ISO/IEC standard of contactless card. The RF protocol is complex, but the designer combined some frequent used command of RF card and then user could operate the cards with full function by sending simple command to the module. The module and antenna is split. The impedance between RF circuit and antenna was tuned by impedance analyzer, and then the module has excellent performance and stability. It connects outside antenna by 50ohm coaxial cable. The surface mount and very small module size are fit to portable devices. Main Characteristics • Module split antenna, connected by 50ohm coaxial cable, flexible antenna size and layout • EMV2010 certification ability • Surface mount and very small module size to fit portable devices • Low power consumption, could be set RF output level • Good Performance in EMC Qualifications • PCD type: NXP CL RC663 • Working frequency: 13.56MHz • RF standard: ISO14443A，ISO14443B，ISO15693 • Card supported: see: module function configuration table • Anti collision ability: Full function anti collision; be able to set multi- cards or single card • Auto detecting card: Supported, default OFF, could be set • Power supply: DC 5V (±10%) • Interface: USB HID, IIC & UART (selected by SPS pin, recommend to use IIC) • Communication speed: IIC: 400Kbps UART: 19200bps, 9600bps, 38400bps, 57600bps, 115200bps USB: USB 2.0 HID • Max. command length: JCP04: 253bytes JCP05: 510bytes • Interface level: UART/IIC: 3.3V (TTL level; 5V tolerance) • Power consumption: Max.: 150mA Idle model: 100uA • Operating distance: 100mm (M1 typical distance, depending on card quality) • Dimension: 20mm*35mm*4.1mm (without Antenna) • Weight: About 10g (without Antenna) • ISP: Supported • RoHS：Supported • Operating temperature: -25 to +85°C • Storage temperature: -40 to +125°C

Minimum Order: 1 bags

Description JMY622 connects outside antenna by 50ohm coaxial cable. It fully supports ISO14443 and ISO15693 cards. It has EMV2010 certification ability, also could be set RF output level. The surface mount and very small module size design are fit to portable devices. The RF protocol is complex, but the designer combined some frequent used command of RF card and then user could operate the cards with full function by sending simple command to the module. The module and antenna is split. The impedance between RF circuit and antenna was tuned by impedance analyzer, and then the module has excellent performance and stability. Main Characteristics • Module split antenna, connected by 50ohm coaxial cable, flexible antenna size and layout • EMV2010 certification ability • Surface mount and very small module size to fit portable devices • Low power consumption, could be set RF output level Qualifications • PCD: NXP MF RC531, SL RC400, CL RC632 • PCB Layers：4 • Working frequency: 13.56MHz • RF standard: ISO14443A, ISO14443B, ISO15693 • Anti collision ability: Full function anti collision; be able to set multi- cards or single card • Auto detecting card: Termsed, default OFF, could be set • Data FLASH: 512 Bytes • Power supply: DC 3.3V & 5V (±10%) • Interface: UART and IIC • Interface level: UART / IIC: 3.3V (TTL level; 5V tolerance) • Communication speed: IIC: Max.200Kbps UART: 19200bps, 9600bps, 38400bps, 57600bps, 115200bps • Max. command length: JCP04: 253bytes JCP05: 510bytes • Power consumption: Max.: 150mA Normal model: 90mA Idle model: 100uA • Operating distance: 100mm (M1 typical distance, depending on card quality) • Dimension: 20mm * 35mm * 4.1mm (without Antenna) • Weight: About 10g (without Antenna) • ISP: Termsed • RoHS: By order • CE certification: in plan (Jan. 17, 2015) • Operating temperature: -25 to +85°C • Storage temperature: -40 to +125°C

Minimum Order: 1 bags

Description JMY6281 is integrated designing. The impedance between RF module and antenna was tuned by impedance analyzer. And then the module has excellent performance and stability. JMY6281 has various functions and supports multi ISO/IEC standard of contactless card. The RF protocol is complex. The designer combined some frequent used command of RF card and then user could operate the cards with full function by sending simple command to the module. JMY6281 support NFC functions: Peer to Peer; Card Mode (PICC); Reader (PCD- VCD). Main Characteristics • Modules integrated antenna, excellent consistency and stability • Support UART or IIC, meanwhile be with USB HID interfaces • Light and slim • The module has a length of 506 bytes command buffer could send APDU over 256 bytes to T=CL smart cards and SAM cards. The modules support FSDI=8 of ISO14443-4. Qualifications • PCD: NXP PN512 CV520 • Working frequency: 13.56MHz • RF standard: ISO14443A, ISO14443B, ISO18092 • Anti collision ability: Full function anti collision; be able to process multi-cards; be able to set operate single card only. • Auto detecting card: Supported, default OFF. The default state can be set. • Power supply: DC 5V (±10%) • Interface: USB HID and UART or IIC by order • Communication speed: IIC: Max.200Kbps UART: 19200bps, 9600bps, 38400bps, 57600bps, 115200bps USB: 2.0 HID class • Max. command length: JCP04: 253bytes JCP05: 510bytes • Interface level: UART / IIC: 3.3V (TTL level; 5V tolerance, by pull up) • Power consumption: 100mA • Operating distance: 80mm (depending on card and antenna design) • Dimension: 50.8mm * 50.8mm * 5mm • Weight: About 20g • ISP: Supported • RoHS: Compliant • Operating temperature: -25 to +85°C • Storage temperature: -40 to +125°C

Minimum Order: 1 bags

Description JMY6804 is a series of RFID read/write module. It has various functions and supports multi ISO/IEC standard of contactless card. The RF protocol is complex, but the designer combined some frequent used command of RF card and then user could operate the cards with full function by sending simple command to the module. The impedance between RF module and antenna was tuned by impedance analyzer. And then the module has excellent performance and stability. Main Characteristics • Ferrite plate under the antenna, good performance for metal-around environments • EMV2010 certification ability in RF protocol part • 2 SAM slots, full fill payment system usage • USB HID interface, convenience to use on PC Qualifications • PCD model: NXP CL RC663 • PCB Layers：4 • Working frequency: 13.56MHz • RF standard: ISO14443A, ISO14443B, ISO15693, ISO7816,NFC • Anti collision ability: Full function anti collision; be able to set multi- cards or single card • Auto detecting card: Supported, default OFF, could be set • SAM slots: 2, T=0 & T=1 9600, 19200, 38400, 55800, 57600, 115200bps • Data FLASH: 512 Bytes • Power supply: DC 5V (±10%) • Interface: USB HID, RS232C, UART or IIC by order • Communication speed: IIC: Max.200Kbps UART: 19200bps, 9600bps, 38400bps, 57600bps, 115200bps USB: 2.0 HID class • Interface level: UART / IIC 3.3V (5V tolerance) • Max. command length: JCP04: 253bytes JCP05: 510bytes • Power consumption: Max. 150mA • Operating distance: 70mm (M1 typical distance, depending on card quality) • Dimension: 70mm * 50mm * 16.5mm • Weight: About 120g • ISP: Supported • RoHS: By order • CE certification: in plan (Jan.17,2015,soon) • Operating temperature: -25 to +85°C • Storage temperature: -40 to +125°C

Minimum Order: 1 bags

Description JMY5041 is the second generation product based on JMY504 with UART and IIC serial port.JMY5041 has various functions and supports multi ISO/IEC standard of contactless card. The RFprotocol is complex. The designer combined some frequent used command of RF card and then usercould operate the cards with full function by sending simple command to the module. The impedance between RF module and antenna was tuned by impedance analyzer. And then the module has excellent performance and stability. The module and antenna is split design. 4 wires are linked the antenna and module. Normally the wire should be less than 200mm, or it will affect the module’s performance and stability. Qualifications • PCD model: NXP CV520、 PN512 • Working frequency: 13.56MHz • Anti collision ability: Full function anti collision; be able to process multi-cards; be able to set operate single card only. • Auto detecting card: Supported, default OFF. The default state can be set. • Power supply: DC 5V (±0.5V) • Interface: IIC & UART (selected by SPS pin, recommend to use IIC) • Communication rate: IIC: Max.200Kbps UART: 19200bps / 9600bps / 38400bps / 57600bps / 115200bps • Max.command length: JCP02 252 Bytes; JCP03 510 Bytes; JCP04 253 Bytes; JCP05 510 Bytes; • Interface level: 3.3V (TTL level; 5V tolerance) • Power consumption: 50mA • Operating distance: 100mm (depending on card and antenna design) • Dimension: 21 mm*42mm • Weight: About 15g • Operating temperature: -25 ~ +85 ℃ (-77 ~ +185°F) • Storage temperature: -40 ~ +125 ℃ (-104 ~ +257°F) • ISP: Supported • RoHS: Compliant

Minimum Order: 1 bags

Description JMY5051 is the second generation product based on JMY505 with UART and IIC serial port. JMY5051 has various functions and supports multi ISO/IEC standard of contactless card. The RF protocol is complex. The designer combined some frequent used command of RF card and then user could operate the cards with full function by sending simple command to the module. The impedance between RF module and antenna was tuned by impedance analyzer. And then the module has excellent performance and stability. The module and antenna is split design. They are connecting by a 50ohm coaxial wire whose length is up to 1000cm in good situation. But the best length of the coaxial line is 60cm. Qualifications • PCD model: NXP CL RC663 • Working frequency: 13.56MHz • Anti collision ability: Full function anti collision; be able to process multi-cards; be able to set operate single card only. • Auto detecting card: Supported, default OFF. The default state can be set. • Power supply: DC 5V (±0.5V) • Interface: IIC & UART (selected by SPS pin, recommend to use IIC) • Communication rate: IIC: Max.200Kbps UART: 19200bps / 9600bps / 38400bps / 57600bps / 115200bps • Max.command length: JCP02 252 Bytes; JCP03 510 Bytes; JCP04 253 Bytes; JCP05 510 Bytes; • Interface level: 3.3V (TTL level; 5V tolerance) • Power consumption: 130mA • Operating distance: 100mm (depending on card and antenna design) • Dimension: 21 mm*42mm • Weight: About 15g • Operating temperature: -25 ~ +85 ℃ (-77 ~ +185°F) • Storage temperature: -40 ~ +125 ℃ (-104 ~ +257°F) • ISP: Supported • RoHS: Compliant

Minimum Order: 1 bags

Description JMY5011 is the second generation product based on JMY501 with UART and IIC serial port.JMY5011 has various functions and supports multi ISO/IEC standard of contactless card. The RFprotocol is complex. The designer combined some frequent used command of RF card and then usercould operate the cards with full function by sending simple command to the module. The impedance between RF module and antenna was tuned by impedance analyzer. And then the module has excellent performance and stability. The module and antenna is split design. 4 wires are linked the antenna and module. Normally the wire should be less than 200mm, or it will affect the module’s performance and stability. Qualifications • PCD model: NXP CL RC663 • Working frequency: 13.56MHz • Card supported: see: module function configuration table • Anti collision ability: Full function anti collision; be able to process multi-cards; be able to set operate single card only. • Auto detecting card: Supported, default OFF. The default state can be set. • Power supply: DC 5V (±0.5V) • Interface: IIC & UART (selected by SPS pin, recommend to use IIC) • Communication rate: IIC: Max.200Kbps UART: 19200bps / 9600bps / 38400bps / 57600bps / 115200bps • Max. command length: JCP02 252 Bytes; JCP03 510 Bytes; JCP04 253 Bytes; JCP05 510 Bytes; • Interface level: 3.3V (TTL level; 5V tolerance) • Power consumption: 130mA • Operating distance: 100mm (depending on card and antenna design) • Dimension: 21 mm*42mm • Weight: About 15g • Operating temperature: -25 ~ +85 ℃ (-77 ~ +185°F) • Storage temperature: -40 ~ +125 ℃ (-104 ~ +257°F) • ISP: Supported • RoHS: Compliant

Minimum Order: 1 bags

Description JMY6123 is a series of RFID read/write module. It has various functions and supports multi ISO/IEC standard of contactless card. The RF protocol is complex, but the designer combined some frequent used command of RF card and then user could operate the cards with full function by sending simple command to the module. The impedance between RF module and antenna was tuned by impedance analyzer. And then the module has excellent performance and stability. The module and antenna is split design. 50ohm coaxial cable are linked the antenna and module. Main Characteristics • Module split antenna, connected by 50ohm coaxial cable, flexible antenna size and layout • EMV2010 certification ability • Metal shield for electromagnetic shielding • 4 SAM slots and 512K bytes data FLASH, full fill payment system usage Qualifications • PCD model: NXP CL RC663 • Working frequency: 13.56MHz • RF standard: ISO14443A, ISO14443B, ISO15693, ISO7816, ISO18000-3MODE3 • Anti collision ability: Full function anti collision; be able to process multi-cards; be able to set operate single card only. • Auto detecting card: Termsed, default OFF, could be set • SAM slots: 4, T=0 & T=1 9600, 19200, 38400, 55800, 57600, 115200bps • Power supply: DC 5V (±10%) • Interface: RS232C, UART by order • Communication speed: UART: 19200bps, 9600bps, 38400bps, 57600bps, 115200bps • Interface level: UART 3.3V (5V tolerance) • Max. command length: JCP04: 253bytes JCP05: 510bytes • Power consumption: Max.150mA • Operating distance: 100mm (M1 typical distance, depending on card quality) • Dimension: 79mm * 55mm * 7.5mm (without Antenna) • Weight: About 30g (without Antenna) • ISP: Supported • RoHS: Compliant • Operating temperature: -25 to +85°C • Storage temperature: -40 to +125°C

Minimum Order: 1 bags

Place of Origin: Guangdong, China Brand Name: UIY Model Number: UIYCI6075A Application: Communica , tions Type: Satellite Series: Coaxial< , br>Features: High Isolation Mounting Type: N / SMA Description: Low Frequency Isolator Product Name: Coaxial Isolator Model No.: UIYCI6075A Frequency Range: 45~270MHz Bandwidth: 40% Insert , ion Loss: 0.5dB Isolation: 25dB VSWR: 1 , .15 Forward Power: 200W Reverse Power: 100W Connector Type: N / SMA

Minimum Order: 1 bags

Type: Waveguide Circulator Model Number: UIYWC2830A18T265 Place of Origin: Guangdong, China Brand Name: UIY Model: UIYWC2830A18T265 Freq , uency Range: 18~26.5GHz VSWR: 1.25 Insertion Loss: 0.3dB Isolation: 20dB Power: , 100W Connector Type: WR42(BJ220) Temperature: -40 ~ +85°C Warranty: 1 Year

Minimum Order: 1 bags

69KV Voltage Height 35FT 10670MM Octagonal Galvanized Distribution Steel Pole Material: Steel Q345 , Gr50. Yield strength of Material: Minimum yield strength ≥345n/mm2 for Q345 S355 and Gr 50 Pole’s height: 35FT, 10670mm Section 1 Wall thickness: 3.0mm Pole's Shape : Octagonal Power: 69KV Welding Welding in accordance with standard of CWB and AWS D 1.1 Galvanization: Hot dip galvanization with min thickness 86µm on average in accordance with Chinese standardGB/T 13912-2002 or American standard ASTM A123, ISO: 2626-1985. Manufactury Capacity Per Day: 250 pcs Wall thickness Tolerance: +- 0.1mm from 2.3mm to 4mm. +- 0.2mm from 5mm to 20mm. +- 0.5mm from 22mm to 30mm Diameter: 127mm / 248mm Finishing Hot Dip Galvanized Temperature range -35 °C~+45 °C Wind Speed: Aganist wind pressure of 120Km/h to 180Km/h. Install Type Burial Type Design Load: 500 KGS Quality Control According to ISO9001-2008 requirements. Certificates ISO9001-2008, SGS Audited Supplier, The AAA grade certificate. Other Less land occupation & easy maintenance Description 69KV Height 35FT 10670MM Octagonal Galvanized Steel Pole was designed as customer's request. Shape with Octagonal and top diameter 127mm, butt diameter 248mm, thickness 3.0mm. Top design Load 500KGS. Used for 69 kv distribution network. and each container can load around 195pcs. Standard Accessories - Top Cap - Butt Plate - Standard hole on X-X , Y-Y , Z-Z. - Grounding Nuts & Bolts Others Standard poles 25FT, 30FT, 35FT, 40FT,45FT Height (ft) Thickness (mm) Butt Diameter (mm) Tip Diameter (mm) Design Load (kg) Yield Stress (MPA) Zinc Coating (microns) 25 2.5 152 120 300 345 86 30 3.0 226 127 500 345 86 35 3.0 248 127 500 345 86 40 3.0 317 127 500 345 86 45 3.0 328 127 500 345 86 Production Process Raw material test Cutting Bending Welding (longitudinal ) Dimension verify Flange welding Hole drilling Calibration Deburr Galvanization or powder coating or Bituminous painting Recalibration Packages 69KV Voltage Height 35FT 10670MM Octagonal Galvanized Distribution Steel Pole 0 Material Test: 1. All of our material are purchased from famous mill factory to assure the quality. 2. A mill certificate issued by the mill factory with stamp and signature must be provided before unload the material in our factory; 3. Before put into production, all the material must pass the chemical and physical analysis to make sure that they have met the requested strength and component. Galvanized Test: Our hot dip galvanized in accordance with ASTM A123, and the thick min 86 microns on average. 69KV Voltage Height 35FT 10670MM Octagonal Galvanized Distribution Steel Pole 1 69KV Voltage Height 35FT 10670MM Octagonal Galvanized Distribution Steel Pole 2 Terms and Conditions 1. Price Term: EXW, FOB, CFR or CIF. Ø EXW: Poles Cost Ø FOB : Pole Cost + Land Transportation + Fee on Port Ø CFR : Pole Cost + Land Transportation + Fee on Port + Sea Freight Ø C I F : Pole Cost + Land Transportation + Fee on Port + Sea Freight + Insurance. 2. MOQ: One 40FT Container. 3. Payment Term: Typically 30% by T/T as deposit, balance by T/T or L/C at sight before shipment. Other payment way can be negotiated. 4. Delivery Time: 15 working days per container after PI / drawing / prepayment confirmed. 5. Package: Normally wrapped by plastic bags or burlap cloth at the top and bottom,or according to clients’ requirement. Company Introduce: Through the efforts of the company staff, the support and cooperation from all over the world. The company's products have been exported to Philippines, Malaysia, Australia, America, Africa, Latin America, Panama, Suriname, Costa Rica, Colombia, Jordan, Nigeria, etc. We have good export experience and with 1 container export to World in average every day.

PRODUCT DESCRIPTION Long Range UGV EOD Robots Video Transmitter HDMI CVBS Low Latency AES256 Encryption 200-2700MHz Introduction The LKAV-C320 is a long range wireless video transmitter supports HD digital (HDMI) and SD analog (CVBS) dual video inputs, based on COFDM and H.264 technologies, it is ideally suits for UGV (Unmanned Ground Vehicle) / EOD Robots video transmission. It can establish solid video link in all environments such as urban city, tunnel and battlefield. Application Scenario Long Range UGV EOD Robots Video Transmitter HDMI CVBS Low Latency AES256 Encryption 200-2700MHz 0 Long Range UGV EOD Robots Video Transmitter HDMI CVBS Low Latency AES256 Encryption 200-2700MHz 1 Features ■ Advanced COFDM modulation ■​ High efficient H.264 compression ■​ Range up to 1-1.5km NLOS ■​ 60-100ms low latency ■​ Support HDMI and CVBS dual video inputs ■​ Compact size and light weight ■​ Rugged aluminum alloy housing ■​ High safety AES256 encryption Specification Transmission Characteristics Modulation COFDM Modulation Type QPSK (4QAM), 16QAM, 64QAM (Default QPSK) Frequency 300MHz-860MHz (Default 700MHz) 860MHz-2.7GHz for customization Transmit Power 30dBm/33dBm RF Bandwidth 2/4/6/8MHz adjustable FEC 1/2, 2/3, 3/4, 7/8 Guard Interval 1/4, 1/8, 1/16, 1/32 Data Characteristics Video Input HDMI (Mini): 1080p/1080i/720p/720i AV: 720x480/60i (NTSC), 720x576/50i (PAL) Video Compression H.264 RF Interface N F head Parameter Settings LED control box Encryption AES256 (support set password) Link Latency ≤80ms Movement Speed Supports ≥120km/h Electrical Characteristics Working Voltage DC12V Working Current ≤1.6A (@12V) Power Consumption ≤20W Physical Characteristics Weight ≤0.9kg (w/o antenna) Dimensions 150*120*45(mm)(L×W×H) Working Temp. -10℃~70℃ Front Panel Long Range UGV EOD Robots Video Transmitter HDMI CVBS Low Latency AES256 Encryption 200-2700MHz 2 ① Power input (12V DC) ② HDMI input (Mini) ③ Audio left channel input ④ Audio right channel input ⑤ Composite video input (CVBS) ⑥ Power push button ⑦ Antenna interface (N F head) Rear Panel Long Range UGV EOD Robots Video Transmitter HDMI CVBS Low Latency AES256 Encryption 200-2700MHz 3 ① Data interface (DB9 for parameter settings)

Octagonal Hot Dip Galvanized Steel Tubular Pole Lap Joint Type Power Steel Poles Product Description: Our steel pole, steel poles , steel power poles , power distribution equipment , electric power transimission &distribution steel poles ,hot-dip-galvanized steel poles ,lamp poles ,street lamp poles ,solar street lamps steel poles ,high mast lamp poles,road lamp poles, the steel street lamp poles, hot-dip- galvanized steel lighting ,outdoor lighting ,outdoor lamps ,street lighting poles ,steel post ,street poles, lamp parts ,lighting fixture ,lighting poles ,lighting equipment ,lighting decoration ,lighting product , street lighting body, high mast lighting steel poles &tower,electric poles, round&square street lighting steel poles with double arm or single arm . Stainless steel poles, Flag mast stainless steel pole, aluminum street light poles, traffic lighting steel poles, telecom tower poles are made by hot-roll steel coil ,the process as cut plate, bending ,forming,automatic welding,drill holes ,quality check before galvanized, hot dip galvanized or powder coating , final quality check according by client required. Product Specification: Products Octagonal Hot Dip Galvanized Steel Tubular Pole Lap Joint Type Power Steel Poles Application Electrical Power Transformer Substation Voltage Grade 220KV Once Forming 16m Once forming without joint Connection structure Overlap / flange connection Shape Octagonal Welding According to AWS D 1.1, CO2 welding or submerged arc auto methods Life Period More than 25 years, it is according to installing environment Painting According to clients' request Joint Joint with insert mode, flange mode. Octagonal Hot Dip Galvanized Steel Tubular Pole Lap Joint Type Custom Painting 0 Production Process: All of our material are purchased from famous factory to assure the high quality. A factory certificate issued by the factory with stamp and signature must be provided before unloading the material in our factory , otherwise we have rights to refuse. Before put into production , all the material must be passed the chemical and physical analysis to make sure that they have met the requested strength and component. Inspection To assure our products qualified , we take steps as follows : 1. Management team : We have employed the experienced senior experts to take charge of the whole management ,especially the technical management and quality management . 2. Introducing ISO management :We are aware of ISO 9001:2008 certificate . 3. QC Inspection :It is our company policy that all the finished products should be inspected by our specialized QC in every manufacture step and before each shipment Design and Detail Lofting and designing software :We have transmission power pole designing software which can help us design all kinds of steel poles ,at the same time ,the TMA and LMA are adopted by us to design the drawing accurately Advantages: The Hot Dip Galvanized Electrical Power Steel Tubular Pole plays an important role in electrical power transmission and distribution industry. In order to meet the increasingly higher demand for steel tubular pole, our company design and produce many kinds of steel tubular pole for the power transmission and distribution system. Besides, our electrical steel tubular pole have been tested and approved by the Transmission Pole Tower Testing Station. As an alternative to the traditional wood and concrete poles, our hot dip galvanized steel tubular pole could be utilize to bear the conductors and electric distribution equipment, power transmission equipment, cables, etc. our company has more than 15 years' design & manufacture experence which enable us to handle volume orders with high quality and low cost. In order to provide better service for customers, we promise to reply within 24 Working Hours and technical support by E-mail and calling service. Packaging&Shipping: * Covered by Plastic Wrap or Mat or according to client's requests. * The Loading Pcs of Each Container could be calculated according to client's specification and data Quantity(Metric Tons) 1 - 1 >1 Est. Time(days) 20 To be negotiated Manufacturing: Raw material: Q235 or Q345 in China. We get the raw material checked in our lab test room. Silicon less than2%. We have carbon and sulfur analyzer to check the elements of the steel sheet. We'll return the steel if they are unqualified. So in this way, we can control the quality of the steel poles from the first beginning. Our factory owns advanced production lines and machines including bending calibration machine, hydraulic plate shears machine, shears machine, slitting machine, 208T hydraulic straightener, etc. All insure us to produce steel poles with the best quality. After the fabrication process as cutting plate, bending, forming, automatic welding, drilling holes, we get poles checked before galvanized, hot dip galvanized and powder coating and finally we get poles checked according to client's requirements. Octagonal Hot Dip Galvanized Steel Tubular Pole Lap Joint Type Custom Painting 1

ME936 HUA-WEI ME936 module 4G LTE WCDMA/HSDPA/HSUPA/HSPA+ GPRS/EDGE NGFF Modules Hua Wei ME936 is an LTE module 4G NGFF interface, LTE support (FDD) B1 / B2 / B3 / B4 / B5 / B7 / B8 / B13 / B17 / B20, penta-band DC-HSPA + / HSPA + / HSPA / WCDMA for North American and European network covering low power consumption, global navigation satellite systems (GNSS), and North American and European carrier certifications, which makes it easier and more flexible, and integration into the terminals. In addition, the ME936 support NGFF characteristics to optimize performance, power consumption, and ease of use. ME936 is an ideal choice for the Ultrabook, laptop, tablet, and so on. D. Features: Brand: Huawei Model: ME936 Operating range: LTE: BI / B2 / B3 / B4 / B5 / B7 / B8 / B13 / B17 / B20 WCDMA / HSDPA / HSUPA / HSPA +: 850 MHz / 900 MHz / 1700 MHz (AWS) / 1900 MHz / 2100 MHz GPRS / EDGE: 850 MHz / 900 MHz / 1800 MHz / 1900 MHz GPS / GLONASS: L1 Data transfer rate: WCDMA PS: UL (384 kbps) / DL (384 kb) DC-HSPA +: UL (11 Mbps) / DL (42 Mbps) LTE FDD: UL (50 Mbps) / DL (100 Mbps) bandwidth @ 20 M (CAT3) GPRS / EDGE multi-slot class 12 GPRS data services: 85.6 kbit / UL / DL 107 kbit / s EDGE: 236.8 kbit / UL / DL 296 kbit / s HSPA +: 5.76 Mbps UL / DL 21.6 Mbit / s Interface: NGFF: Supply voltage range: 3.135 V ~ 4.4 (3.3 recommended) GPS / GLONASS GNSS: Autonomous GPS, A-GPS, GPS XTRA, GLONASS Features: Hot-swappable SIM IPV6 BodySAR Ultrabook function support (LAW, wi-fi unloading, DPTF) MIN USB (Link Power Management) tunable Antenna MO and MT support PDU format support point-to-point base station and The interface antenna Main and auxiliary (supporting Diversity and GPS at the same time) MM4829-2702RA4 for MURATA or other equivalent parts Sms-new signal message. SMS Management: read SMS, write SMS, send SMS, delete SMS and SMS list MO and MT support point-to-point operating system Windows 7/8 / 8.1 / Android 4.0 or later / Chrome OS physical Features Dimensions (L × W × H): 42 mm × 30 mm × 2.3 mm Weight: about 6 grams Power Supply Supply voltage range 3.135V~4.4V (3.3 V recommended) Temp Range Normal operation: -10°C to +55°C Extended operation: -20°C to +70°C Storage: -40°C to +85°C Data Transfer Rate WCDMA PS: UL (384 kbps)/ DL (384 kbps) DC-HSPA+ : UL (11 Mbps)/ DL (42 Mbps) LTE FDD: UL (50 Mbps)/ DL (100 Mbps) @Bandwidth 20M (CAT3) GPRS/EDGE: Multi-slot Class 12 Module show: HUA-WEI ME936 4G LTE Module WCDMA/HSDPA/HSUPA/HSPA+ GPRS / EDGE NGFF Modules 0 HUA-WEI ME936 4G LTE Module WCDMA/HSDPA/HSUPA/HSPA+ GPRS / EDGE NGFF Modules 1 ABOUT US TOP offers communication antennas & modules with wonderful solution, Perfect after-sales service, strict quality testing and competitive price. module brands includes Sierra Wiressless, Simcom, QUECTEL,Cinterion, U-blox, Hua wei , ZTE, Holux, GlobaTop, Skylab, Telit, etc. We're also one of the biggest stocking distributors of active and passive electronic components located in Shenzhen,