Telecom Equipment & Accessories

Product Descriptions The OLSP3112L-CD compatible with Extreme Product apply to dual data-rate of 1.25Gbps/1.0625Gbps and 10km transmission distance with SMF. The transceivers are compatible with SFP Multi-Source Agreement (MSA) and SFF-8472. For further information, please refer to SFP MSA. Optical Characteristics (TOP(C) = 0 to 70 ℃, TOP(I) =-40 to 85 ℃,VCC = 3.13 to 3.47 V) Parameter Symbol Min. Typ Max. Unit Note Transmitter Operating Wavelength λ 1290 1310 1330 nm Ave. output power (Enabled) PAVE -9 -3 dBm 1 Extinction Ratio ER 9 dB 1 RMS spectral width Δλ 0.65 nm Rise/Fall time (20%~80%) Tr/Tf 0.26 ns 2 Dispersion penalty TDP 3.9 dB Output Optical Eye Compliant with IEEE802.3 z (class 1 aser safety) Receiver Operating Wavelength λ 1310 nm Receiver Sensitivity PSEN1 -22 dBm 3 Overload PAVE 0 dBm 3 LOS Assert Pa -35 dBm LOS De-assert Pd -24 dBm LOS Hysteresis Pd-Pa 0.5 dB

PRODUCT DESCRIPTION 10/100M Mini Industrial Network Switch 1 SFP Fiber Port To 2 UTP Overview IM-FS120FE series is the 10/100 Mbps industrial fiber switch, operating temperature-40 ℃ to + 85 ℃, support wide voltage dual power input, meet IP40 protection degree and EMC industrial grade requirements, DIN rail installation, pass through dangerous environmental certification, and comply with FCC and CE standards. The reliable industrial grade design could ensure continuous and stable operation of the automation system. Product Details 2 x 10/100Mbps Auto-sensing RJ45 ports 1 x 100Mbps SFP fiber port 4 KV Ethernet surge protection, adapt to a harsh outdoor environment Support Auto MDI/MDIX Flow control mode: full duplex with IEEE 802.3x standard, half-duplex with Back pressure standard IEEE 802.3 10Base-T and IEEE 802.3u 1000Base-TX compliant A store-and-forward switching mechanism Operating environment temperature:-40 ° ~85 ° c Transmission mode: storage and forward System bandwidth:40Gbps (non-traffic jam) 10BASE-T: CAT3, CAT4, CAT5 un-shielded twisted pair(≤100m) 100/1000BASE-TX: CAT5 or above shielded twisted pair(≤100m) Transmission distance: 20Km,40Km,60Km,80Km,100Km LEDs: Power, network, fiber Input voltage:DC 9-52V No-load power:5W Reverse connection: support Storage temperature:-40°～ 85°C Working humidity:10%～90%,non-condensing Storage humidity:10%～95%,non-condensing Safety: CE Mark, commercial CE/LVD EN60950 Warranty: 5 years Industry Standards EMI: FCC Part 15 Subpart B Class A, EN 55022 Class A EMS: EN 61000-4-2 (ESD) Level 3,EN 61000-4-3 (RS) Level 3, EN 61000-4-4 (EFT) Level 3,EN 61000-4-5 (Surge) Level 3, EN 61000-4-6 (CS) Level 3,EN 61000-4-8 Traffic Control: NEMA-TS2 Vibration: IEC 60068-2-6 Freefall: IEC 60068-2-32 Shock: IEC 60068-2-27 Rail Traffic: EN 50121-4 Mechanical information Shell: Corrugated metal shell Safety class: IP40 Dimension: 113.8 x 93 x 34.9mm Mounting method: Din-rail mounting Lead Time Quantity(Pieces) 1-100 >100 Times(Days) 3 Negotiable Application IP40 Industrial Network Switch 0 IP40 Industrial Network Switch 1

Product Description Clear EVA Fiber Optic Heat Shrink Sleeve For Patch Panels Application For Fiber Optic Patch Panels/ODF/Fiber Distribution Box Cross Connect Cabinet/Splice Tray/Splice Closures Fiber Optic Splice Protection Sleeve, also called Fiber Optic Heat Shrink Tube. It is designed for enhancing protection or supporting positioning of optical fiber splicing. Fiber Optic Splice Protection Sleeve consists of heat shrink tube, hot melt tube and steel rod or ceramic rod. The hot shrink tube is usually made of PE or EVA, and the melt tube is EVA. As for the steel rod, which is made of stainless steel 304 or 201.

FTTH OLT Mini 4pon Epon Olt Gigabit Uplink Port Supply Fttx Solutions Overview HA7004S mini size OLT offers four SFP PON ports and 4 1000M RJ45 uplink ports. SFP slots support hot plugging. Each PON port supports 1:64 optic distribution, total 256 ONUs access.. It meets China Telecom EPON standards CTC V2.1, supports to work with different manufacturers’s GEPON system which also meet CTC standards.It works with HA7200 and HA400 series ONU and passive optical splitter, to establish a passive optic network. Technical Specification Parameter Specification Wavelength 1310(RX)/1490(TX) Optical power +2.5~ +7dBm Receiving Sensitivity -27dBm Maximum distance 20km Maximum optic ratio 1:64 Capacity 4PON System, 256 ONUs MAC 16K Port 4 Gigabit SFP PON ports 4 GE Uplink ports 1 FE management port 1 RS232 DB9 serial port MTBF 100000 hours FAQ Q: Are you manufacturer or trading company? A: Manufacturer, and industry network total solution provider. Q: Do you accept ODM or OEM? A: Yes. We provide customized service for our clients. Q: What is your minimum order quantity? A: MOQ is 1 PCS. 4 1000M RJ45 Uplink Ports 4 SFP PON Ports SFP EPON OLT Mini Size 0 4 1000M RJ45 Uplink Ports 4 SFP PON Ports SFP EPON OLT Mini Size 1

Introduction MWS-12-43B-20 Transceivers are a high performance, cost effective module which have a single LC optics interface. They are compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA) and Digital diagnostics functions are available via the 2-wire serial bus specified in SFF-8472. The receiver section uses a PIN receiver and the transmitter uses a 1490 nm DFB laser, up to 14dB link budge ensure this module 1000Base-LX Ethernet 20km application. Features 1. Up to 1.25Gb/s Data Links 2. Hot-Pluggable 3. Single LC connector 4. Up to 20 km on 9/125μm SMF 5. 1490nm DFB laser transmitter 6. 1310nm PIN photo-detector 7. Single +3.3V Power Supply 8. Monitoring Interface Compliant with SFF-8472 9. Maximum power dissipation <1W 10. Industrial /Extended/ Commercial operating temperature range: -40°C to 85°C/-5°C to 85°C/-0°C to 70°C Version available 11. RoHS compliant and Lead Free

Minimum Order: 1 bags

Product Description 1.25Gb/s GLC-T 10/100/1000M Copper Ethernet SFP Transceiver 100m Description GLC-T10/100/1000 copper SFP transceiver is high performance, cost effective module compliant with the Gigabit Ethernet and 10/100/1000BASE-T standards as specified in IEEE 802. 3-2002 and IEEE 802.3ab, which supporting 10/100/1000Mbps data- rate up to 100 meters reach over unshielded twisted-pair category 5 cable. The GLC- T10/100/1000 supports 10/100/1000 Mbps full duplex data-links with 5-level Pulse Amplitude Modulation (PAM) signals. All four pairs in the cable are used with symbol rate at 250Mbps on each pair. The GLC-T10/100/1000 provides standard serial ID information compliant with SFP MSA, which can be accessed with address of A0h via the 2-wire serial CMOS EEPROM protocol. The physical IC can also be accessed via 2-wire serial bus at address ACh. Features Up to 1.25Gb/s bi-directional data links Hot-pluggable SFP footprint Extended case temperature range (-40°C to +85°C ) Fully metallic enclosure for low EMI Low power dissipation Compact RJ-45 connector assembly Detailed product information in EEPROM +3.3V single power supply Access to physical layer IC via 2-wire serial bus 10/100/1000 BASE-T operation in host systems with SGMII interface Compliant with SFP MSA Compliant with IEEE Std 802.3TM-2002 Compliant with FCC 47 CFR Part 15, Class B RoHS Compliant Products Applications 1.25 Gigabit Ethernet over Cat 5 cable Switch/Router to Switch/Router Link High speed I/O for file severs Optical Parameters Parameter Symbol Min. Typical Max. Units Notes/Conditions Supply Current Is 320 375 mA 1.2W max power over full range of voltage and temperature. See caution note below Input Voltage Vcc 3.13 3.3 3.47 V Referenced to GND Surge Current Isurge 30 mA Hot plug above steady state current. See caution note Parameter Symbol Min. Max. Units Notes/Conditions SFP Output LOW VOL 0 0.5 V 4.7k to 10k pull-up to host_Vcc. SFP Output HIGH VOH host_Vcc -0.5 host_Vcc + 0.3 V 4.7k to 10k pull-up to host_Vcc. SFP Input LOW VIL 0 0.8 V 4.7k to 10k pull-up to Vcc. SFP Input HIGH 2 Vcc + 0.3 V V 4.7k to 10k pull-up to Vcc. Transmission Line-SFP Parameter Symbol Min. Typical Max. Units Notes/Conditions Line Frequency fL 125 MHz 5-level encoding, per IEEE 802.3 Tx Output Impedance Zout,TX 100 Ohm Differential Rx Input Impedance Zin,RX 100 Ohm Differential

Product Description 12F Fiber Optic MTP / MPO - 12 x LC Breakout Cable OM3 OM4 LSZH / PVC The MPO connector offers up to 12 times the density of standard connectors, providing significant space and cost savings. MPO connectors utilize precision molded MT ferrules, with metal guide pins and precise housing dimensions to ensure fiber alignment when mating. The MPO can be mass terminated in combinations of 4, 8, or 12 fiber ribbon cables. The MPO Adapter comes standard in black. Fiber Optic MTP / MPO - LC Breakout Cable - Features: Precision molded MT ferrule High precision guide pins for exact alignment Compact design, up to 4,8,12,24 fibers IEC 61754-7 Compliant EIA/TIA-604-5 Compliant Fiber Optic MTP / MPO - LC Breakout Cable - Applications: Telecommunication Networks Asynchronous Transmission Mode(ATM) Gigabit Ethernet Active Deviced/Transceiver Interface CATV, Video and Multimedia Premise Installations Telecommunication Networks Parallel optical interconnect between PC Cards and patch panels Interconnection for O/E modules Industrial & Military Optical Switch interframe connections Fiber Optic MTP / MPO - LC Breakout Cable - Specifications: Item LC,SC,ST,FC....... MPO/MTP End face type PC,UPC and APC PC and APC Fiber type SM(G652,G655,G657)；MM(OM1-OM5) Core number 12,24 Cable Diameter 0.9,2.0,3.0 Mini Round cable:Max4.5mm； Ribbon cable:Max3.0*5.0mm Insertion loss(dB) ≤ 0.3 Standard:≤0.35/0.7(Typical/Max) Low Loss:≤0.2/0.35(Typical/Max) Return loss(Min) UPC SM:40dB APC SM:60 dB PC MM:25 dB SM: APC:60dB MM: PC:20dB Test Wavelength (nm) SM:1310/1550 , MM:850/1300 Repeatability ≤ 0.1dB Durability ≤ 0.2dB Interchangeability ≤ 0.2dB Operating Temperature -20

Product Description Compatible Dell QSFP+ 40GE LR4 1310nm Duplex LC Fiber Transceiver Module Description This Dell® QSFP-40G-LR4 compatible QSFP+ transceiver provides 40GBase-LR4 throughput up to 10km over single-mode fiber (SMF) using a wavelength of 1270nm to 1330nm via an LC connector. It is guaranteed to be 100% compatible with the equivalent Dell® transceiver. This easy to install, hot swappable transceiver has been programmed, uniquely serialized and data-traffic and application tested to ensure that it will initialize and perform identically. Digital optical monitoring (DOM) support is also present to allow access to real-time operating parameters. This transceiver is Trade Agreements Act (TAA) compliant. We stand behind the quality of our products and proudly offer a limited lifetime warranty. Features Hot-pluggable QSFP form factor Supports 39.8 Gb/s to 44.6 Gb/s 18.5 dB link insertion loss budget Single 3.3V power supply Maximum link length of 40km on Single Mode Fiber (SMF) Uncooled 4x10Gb/s CWDM transmitter XLPPI electrical interface Duplex LC receptacles Operating case temperature range: 0 to 70°C 3.5W maximum power dissipation RoHS-6 compliant (lead free) Application 40G Ethernet Infiniband QDR, DDR and SDR Datacenter and Enterprise networking Recommended Operating Environment Parameters Symbol Min. Typ. Max. Unit Case Operating Temperature TOP 0 - +7 , 0 °C Supply Voltage VCC +3.13 +3.3 +3.47 V Data Rate, per lane DR 10.3125 11.2 Gb/s Dat , a Rate Accuracy ΔDR -100 +100 ppm Bit Error Rate BER 10-12 Supply Current ICC 1000 mA Power Consumption P 2.5 3.5 W Transceiver Power-on Initialization Time 2000 ms Control Input Voltage High VIH 2.0 Vcc V Control Input Voltage Low VIL GND 0.7 V Control Output Voltage High VOH 2.0 Vcc V Control Output Voltage Low VOL GND 0.7 V Optical Parameters(TOP = -40 to 85°C, VCC = 3.135 to 3.465 Volts) Optical Transmitter Performance Parameters Symbol Min , . Typ. Max. Unit Note< , br> Operating Date Rate, per Lane DR 10.3125 11.2 Gb/s Total Average Launch Power TPAVG +8.3 dBm Average Launch Power, per Lane PAVG -7.0 +2.3 dBm Optical Modulation Amplitude (OMA), per lane POMA -5.0 +3.5 dBm 1 Difference in Launch Power between any two Lanes (OMA) PTX-DIFF 6.5 dB Transmitter Dispersion Penalty, per Lane TDP 2.3 dB Launch Power in OMA minus Transmitter and Dispersion Penalty (TDP), per Lane OMA- TDP -4.8 dB Optical Wavelength, each Lane λL0 1264.5 1271 , 1277.5 nm λL1 1284.5 1291 1297 , .5 nm λL2 1304.5 1311 1317 , .5 nm λL3 1324.5 1331 1337 , .5 nm Spectral Width (-20dB) Δλ 1 nm Side Mode Suppression Ratio SMSR 30 dB Optical Extinction Ratio ER 3.5 dB Optical Eye Mask { X1, X2, X3, Y1, Y2, Y3 } { 0.25, 0.4, 0.45, 0.25, 0.28, 0.4 } 2 Average Launch Power OFF, per Lane POFF -30 dBm Relative Intensity Noise (OMA) RIN -128 dB/Hz Optical Return Loss Tolerance ORLT 12 dB Transmitter Reflectance RTX -12 dB Input Differential Impedance ZIN 85 100 1 , 15 Ω Differential Data Input Voltage VIN-PP 150 1200 mVpp Optical Receiver Performance Parameters Symbol Min , . Typ. Max. Unit Note< , br> Operating Date Rate, per Lane DR 10.3125 11.2 Gb/s Damage Threshold, per Lane DTH +3.3 dBm 1 Average Receive Power, per Lane PRX-AVG -13.7 +2.3 dBm Receiver Power (OMA), per Lane PRX-OMA +3.5 dBm Receiver Sensitivity (OMA), per Lane SENAVG -11.5 dBm 2 Stressed Receiver Sensitivity (OMA), per Lane SENSOMA -9.9 dBm 3 Receiver Reflectance RRX -26 dB LOS De-Assert LOSD -15 dBm LOS Assert LOSA -30 dBm LOS Hysteresis LOSHY 0.5 dB Receiver Electrical 3dB upper Cutoff Frequency, per Lane FCUT 12.3 GHz Output Differential Impedance ZOUT 85 100 , 115 Ω Differential Data Output Voltage VOUT-PP 370 600 950 mVpp

Description: ADSS cable is made of non-metallic material and self-supporting with the aerial power transmission line. The tension resistance material is aramid yarn with high elasticity modules. And optimizing structure can deploy the weight of the cable and its mechanical and physical properties appropriately and minimize the load on the tower. Loose tube construction, tubes jelly filled, elements (tubes and filler rods) and water blocking yarn laid up around non-metallic central strength member,polyester yarns used to bind the cable core, water blocking tape longitudinally wrapped around the cable core, thenaramid yarn reinforced and PE outer sheath. Cable Mechanical characteristic core Cable diameter weight 2 core to 60core 12±0.5mm 140±5kg/km 72core 13±0.5mm 190±5kg/km 96core 14.5±0.5mm 220±5kg/km 144core 16.5±0.5mm 240±10kg/km Rec.daily max working tension 88kn Max. Allowable working tension 32.7kn Modulus of elasticity 37kn/mm2 Min Bending Radius(mm) operation 240mm installation 390mm Extra load Extra load 0.5%-0.7% Ice 5mm Wind speed 35m/s Corning ADSS Fiber Optic Cable 48 Strand Fiber Reinforced Plastic 0

Product Description 155Mbps 1550nm 80km SFP Optical Transceiver Description and Characteristics This transceiver is hot pluggable 3.3V Small-Form-Factor transceiver module. It designed expressly for high-speed communication applications that require rates up to 155mbps,it designed to be compliant with SFF-8472 and SFP+ MSA. The module data link up to 80km in single mode fiber. OPTICKING SFP+ transceivers provide a unique enhanced digital diagnostic monitoring interface, which allows real-time access to device operating parameters such as transceiver temperature,laser bias current, transmitted optical power, received optical power and transceiver supply voltage.It also defines a sophisticated system of alarm and warning flags, which alerts end-users when particular operating parameters are outside of a factory set normal range. Product Features Class 1 laser product EN 60825-1-standards Operating data rate up to 2.67Gbps Compliant with SFP MSA and SFF-8472 Compliant with SDH/SONET Hot pluggable 3.3V single Power supply RoHS-6 Compliant Operation Temperature Range : X means C( 0~70°C); I(-40~85°C). Ordering Information Product Number Wavelength Data rate Distance TX Power RX Sens LD PD DDM KSFP01-5531SL20X 1550nm/1310nm 155Mb/s 20KM -15~-8dbm <-33dbm FP PIN YES KSFP01-3155SL20X 1310nm/1550nm 155Mb/s 20KM -15~-8dbm <-33dbm FP PIN YES KSFP01-5531SL40X 1550nm/1310nm 155Mb/s 40KM -9~-3dbm <-33dbm FP PIN YES KSFP01-3155SL40X 1310nm/1550nm 155Mb/s 40KM -9~-3dbm <-33dbm FP PIN YES KSFP01-5549SL60X 1550nm/1490nm 155Mb/s 60KM -5~0dbm <-34dbm DFB PIN YES KSFP01-4955SL60X 1490nm/1550nm 155Mb/s 60KM -5~0dbm <-34dbm DFB PIN YES KSFP01-5549SL80X 1550nm/1490nm 155Mb/s 80KM -5~0dbm <-34dbm DFB PIN YES KSFP01-4955SL80X 1490nm/1550nm 155Mb/s 80KM -5~0dbm <-34dbm DFB PIN YES KSFP01-5549SL12X 1550nm/1490nm 155Mb/s 120KM 0~5dbm <-34dbm DFB PIN YES KSFP01-4955SL12X 1490nm/1550nm 155Mb/s 120KM 0~5dbm <-34dbm DFB PIN YES KSFP03-5531SL20X 1550nm/1310nm 1.25Gb/s 20KM -9~-3dbm <-22dbm FP PIN YES KSFP03-3155SL20X 1310nm/1550nm 1.25Gb/s 20KM -9~-3dbm <-22dbm FP PIN YES KSFP03-5531SL40X 1550nm/1310nm 1.25Gb/s 40KM -5~0dbm <-23dbm DFB PIN YES KSFP03-3155SL40X 1310nm/1550nm 1.25Gb/s 40KM -5~0dbm <-23dbm DFB PIN YES KSFP03-5549SL60X 1550nm/1490nm 1.25Gb/s 60KM -2~3dbm <-24dbm DFB PIN YES KSFP03-4955SL60X 1490nm/1550nm 1.25Gb/s 60KM -2~3dbm <-24dbm DFB PIN YES KSFP03-5549SL80X 1550nm/1490nm 1.25Gb/s 80KM 0~5dbm <-24dbm DFB PIN YES KSFP03-4955SL80X 1490nm/1550nm 1.25Gb/s 80KM 0~5dbm <-24dbm DFB PIN YES KSFP03-5549SL12X 1550nm/1490nm 1.25Gb/s 120KM 0~5dbm <-30dbm DFB APD YES KSFP03-4955SL12X 1490nm/1550nm 1.25Gb/s 120KM 0~5dbm <-30dbm DFB APD YES KSFP04-5531SL20X 1550nm/1310nm 2.5Gb/s 20KM -5~0dbm <-18dbm FP PIN YES KSFP04-3155SL20X 1310nm/1550nm 2.5Gb/s 20KM -5~0dbm <-18dbm FP PIN YES KSFP04-5531SL40X 1550nm/1310nm 2.5Gb/s 40KM -2~3dbm <-20dbm DFB PIN YES KSFP04-3155SL40X 1310nm/1550nm 2.5Gb/s 40KM -2~3dbm <-20dbm DFB PIN YES KSFP04-5549SL80X 1550nm/1490nm 2.5Gb/s 80KM 0~5dbm <-28dbm DFB PIN YES KSFP04-4955SL80X 1490nm/1550nm 2.5Gb/s 80KM 0~5dbm <-28dbm DFB PIN YES

om3 mpo mtp Patch Cord/3m pvc/lszh aqua trunk cable patch code cable mpo Range of Mode Single mode or Multi mode Cable Type Simplex, Duplex Ziocord. or Multi-cores Connector Style SC, FC, ST, LC, MTRJ, E2000, MU, MPO /MTP.etc Polish or Ferrule Interface Type PC, UPC Cable Diameter 0.9mm, 1.2mm, 1.6mm, 1.8mm,2.0mm, 3.0mm Outer Jacket PVC /LSZH/OFNP Jacket Color SM Yellow OM1, OM2 Orange OM3 Aqua OM4 Aqua or Violet OM5 Lemon Green Durability 500 cycles(0.2 dB max increase). 1000mate/de mate cycles Operating Temp. -20 ℃ to +70℃/+85℃ (armored) Storage Temp. -40℃ to +85℃ Product Description MPO Female to MPO Female OM4 (OM3) Multimode Trunk Cable MPO trunk cable, a cost-effective alternative to time-consuming field termination, is designed for high-density fiber patching in data centers which need space saving and reduce cable management troubles. With MPO connectors and good quality fiber, it is optimized for 40G QSFP+ SR4/CSR4, 100G QSFP28 SR4 optics direct connection and high-density data center applications. Please note: MTP connectors are fully compliant with the MPO standards, achieving higher performance levels when compared to generic MPO connectors. Item Single mode Multimoe PC UPC Other Mode 62.5/125 50/125 OM1/2 50/125 OM3/4/5 Insert. Loss 0.2dB Max. (0.15dB Elite) 0.2dB Max. (0.15dB Elite) Return Loss ≥50 dB ≥55 dB ≥60 dB ≥35 dB Insert. Loss/MTP or MPO 0.7dB Max. (0.35 dB Elite.) 0.5dB Max. (0.35dB Elite.) Return Loss s/MTP or MPO ≥50dB ≥55 dB ≥60 dB ≥20dB Pull strength ≥68N ≥68N ≥68N ≥68N Easy to connect and distribute,Compact and superior design Small structure design minimizes cable density and storage space Low insertion loss and hign return loss,Numbers of fibers:1,2,4,8 or 12 Single mode(PC,UPC or APC) and multiple mode PC polish Comply with Telcordia GR-326-CORE specification ROHS Directive-compliant,Flammability:UL 94 V0 OM3 MPO MTP Patch Cord 3M PVC / LSZH Aqua MPO Trunk Cable 0 Related Products 24 Core MPO MTP 2.0mm 3M Optical Fibre Patch Cords in Blue PC UPC Company Information 24 Core MPO MTP 2.0mm 3M Optical Fibre Patch Cords in Blue PC UPC OM3 MPO MTP Patch Cord 3M PVC / LSZH Aqua MPO Trunk Cable 3

Description 100G and 40GBASE SR-BiDi QSFP Transceiver, LC, 100m OM4 MMF Wavelength 832nm - 918nm Max Cable Distance 70m OM3, 100m OM4, 150m OM5 Connector LC duplex Media MMF Transimitter Type VCSEL 850/900nm Receiver Type PIN TX Power -6~4dBm(100G), -4~5dBm (40G) Receiver Sensitivity -7.9 (100G), -6 (40G)

Minimum Order: 1 bags

The 100G QSFP28 DAC wire assemblies are high performance, affordable I/O remedies for LAN, HPC and also SAN. The high speed cord settings up fulfill and go beyond 100 Gigabit Ethernet, InfiniBand EDR and temperature demands for performance as well as dependability. The hilink's electric cable attributes: 1. Suitable with IEEE 802.3 bj, IEEE 802.3 by and also InfiniBand EDR 2. Sustains aggregate information rates of 100Gbps 3. Maximized building and construction to decrease insertion loss and cross talk 4. In reverse compatible with existing QSFP+ adapters and also cages 5. Pull-to-release slide lock design 6. 26AWG via 30AWG wire 7. Straight and break out setting up arrangements offered 8. Customized cable braid termination limits EMI radiation 9. Personalized EEPROM mapping for wire trademark 10. RoHS compliant. Hilink Product Guide Active Optics A: (QSFP+, SFP+, XFP, SFP28, QSF28, Media converters, QSFP AOC) Active Optics B: (6G SFP, 4G SFP, 2.5G SFP, 1.25G SFP, 1.25G GBIC, 622M, 155M ) Cables Interconnect (Active Optical Cable, Direct-Attach Cable DAC) EDFA, DCM Passive products (CWDM, DWDM MUX/DEMUX, AAWG, MPO/MTP, FWDM, Optical circulator, Isolator) https://www.hilinktech.com/

100GHz C Band DWDM AAWG (Athermal Arrayed Waveguide Grating) Mux/Demux Module uses high stable and also reliable transmission capacity in an economical and small plan. It's utilized with10G 80km DWDM SFP+ Transceiver for Long-Haul transportion. DWDM Mux/Demux ITU Wavelength supplies the capacity to combine your services over a solitary connection, whether voice, data, or Internet. Usage fiber wavelength is unlimited, allowing for increased control and also scalability. ITEM SUMMARY The hilink's product features: Ø Athermal design runs over running temperature level array Ø Big channel number Ø Compact dimension Ø High security and dependability Ø Low insertion loss, high isolation boost system margin Applications: DWDM Network DWDM transmission Metro and long haul network Cilick it for more information https://www.hilinktech.com/passive-xwdm/