Power Supplies & Equipment

Qx80h is Mitsubishi q series DC high-speed input module, negative common terminal type, 16 points. Qx80h price (face price), the market stock is very small. Qx80h Parameter Description: 24VDC / 4mA, common cathode, 16 points, terminal block (high speed). Specification details of Mitsubishi PLC module qx80h: [input form] DC input module (negative common end) [input points] 16 points [isolation method] Optocoupler [rated input voltage] DC24V (+ 20% - 15%, ripple coefficient above 5%) [rated input current] about 6mA [derating chart] [on voltage / on current] 13V or higher / 3mA or higher [off voltage / off current] 8V or less / 1.6mA or less [input impedance] about 3.9k Ω [function setting SW2] off interrupt, on high speed input [dielectric withstand voltage] 560vac MS / 3 cycles (altitude 2000m (6557.38 feet)) [insulation resistance] 10m Ω or higher measured by insulation resistance tester [immunity] through 1500vp-p noise voltage, 1 μ Voice simulator with s voice width and 25 to 60Hz voice frequency First instantaneous voice iec61000-4-4: 1kV [protection grade] IP2X [common terminal arrangement] 8 points / common terminal (common terminal: tb9, tb18) [I / O points] 16 (I / O allocation is set to 16 point high-speed input module or interrupt module.) [working status indicator] set by setting in GX developer switch [running indicator] on indication (LED) [external connection] 18 point terminal block (M3 * 6 screw) [applicable wire diameter] core 0.3mm2 to 0.75mm2 (maximum outer diameter 2.8mm) [applicable to clamping terminal] R1 25 ~ 3 (clamping terminal with sleeve cannot be used) [5VDC internal current consumption] 80mA (standard: all points on) [overall dimension (h * w * d)] 98 * 27.4 * 90 [mm] [weight] 0.16kg

Minimum Order: 1 bags

4-axis, differential driver output type. Control unit: pulse. Number of positioning data: 10 data / axis. Maximum pulse output: 4mpps. 40 pin connector. Differential output. Ideal solution for simple multi axis positioning. Perfect match with stepper motor control gi71e71-100 reference manual. The acceleration and deceleration are smooth and the speed changes slightly. The speed of starting processing of positioning control is accelerated. Locate the module. Open collector output type qi71e71-100 differential driver output type It can be divided into two types: open circuit collector output type and differential driver output type The output positioning module of the differential driver can reliably transmit the high-speed command pulse (up to 4mpps) to the servo amplifier, and the transmission distance can reach 10m to realize high-speed and high-precision control. (the maximum command pulse of open collector positioning module is 200kpps.) Reduce system downtime and recovery time. With a simple operation, you can back up all the data in the CPU to the memory card gi71e71-100 reference manual. Through regular backup, the latest parameters and programs can be saved to the memory card all the time. In case of CPU failure, after replacing the CPU, the system can be restored through simple operation and through the memory card with data backed up in advance. As a result, there is no need to spend time managing backup data, and the recovery time can be reduced when the system is down. Input and output points: 4096 points. Number of input and output components: 8192 points. Program capacity: 200K steps. Processing speed: 0.0095 us. Program memory capacity: 800KB. Support USB and network. Support the installation of memory card. High speed communication between multiple CPUs The fixed scanning interruption time is shortened and the device is high- precision. The minimum interval of fixed cycle interrupt program is reduced to 100US. It can accurately obtain high-speed signal, and realize high-speed control qj71e71-100 for parallel processing of device communication (cycle is 0.88ms). The high-speed communication cycle between multiple CPUs is synchronized with the motion control, so the operation efficiency can be maximized. In addition, the performance of the latest motion control CPU is twice that of the previous model Ensure high-speed and high-precision machine control. Slot 1: no power supply is required: install the large ans series PC module with a thousand. The base plate of ANS series PLC. Qa1s series PLC 1 slot main base plate. Ans series modules can be installed. rs-232 1ch。 rs-422/485 1ch。 Through qi71c24n (- 2) RS-232 serial communication, the programmable controller can be programmed and monitored with programming tools. Qi71c24n (- R2) has the function corresponding to the public telephone line modem. The modem used can be initialized, and the connection with the target equipment can be processed. The communication can be carried out through remote equipment and programming tools, modems and public telephone lines. Using the remote password function, The Q series programmable controller can be accessed illegally via the modem function of ai71c24n (- R2). Serial communication module that can collect / change data, monitor / manage, measure data collection, etc. of programmable controller. High speed and large capacity communication qj71e71-100 manual with maximum speed of 230.4kbps and maximum 9960 words (during MC protocol communication). The reading / writing qi71e71-100 Manual of the data in the programmable controller can be executed by using the MC protocol through external devices (PC, display, etc.). By selecting the non sequential protocol and using the sequential program for communication control, between the programmable controller and the external equipment (bar code reader, measuring equipment, etc.), Use the local protocol of the external device to communicate with it.

Minimum Order: 1 bags

Specification of Mitsubishi FL net interface moudel qj71fl71-t-f01: 1. Transmission instructions [data transfer speed] 100base-tx: 100Mbps (full duplex / half duplex) 10Base-T: 10Mbps (half duplex) [transmission mode] baseband [electronic interface] IEEE802 3 standard (CSMA / CD standard) [Transport Protocol] UDP / IP FA link protocol [maximum section length] 100m [maximum number of stations in the system] 254 [maximum number of sites] 254 modules / all internal address blocks [minimum station spacing] 2.5m [cyclic data amount] maximum (8K bits + 8K words) / system, maximum (8K bits + 8K words) / station [information data capacity] 1024 bytes maximum 2. Link data description [public storage area] area 1 (bit area) 8K / bit area 2 (word area) 8K words [virtual address space and physical memory] none [error record storage area] 512 words [status storage area] bit area 2K / bit word area 2K [local station network parameter setting area] 96 words [network parameter setting area of other stations] 2048 words [network parameter acquisition area] 512 words [soft component storage area] 512 words [information area (instantaneous area)] 1024 bytes * 2 at most (transmit receive each) 3. Transmission instructions [information transmission] 500ms or less (1:1 one-way information arrival time) [token start time] Newly added: start time = 3000 + (minimum number of sites / remaining 8) * 4 + 1200ms Joining: joining time = refresh cycle * 3 + number of local stations * 4ms 4. Other specifications [input / output points] 32 points (I / O allocation: smart) [5VDC internal current consumption] 0.50a [noise resistance, voltage resistance, insulation resistance] according to the power instructions for installing the fl net site [external dimension h * w * D] 98 * 27.4 * 90mm [weight] 0.11kg

Minimum Order: 1 bags

Adapter for mounting DIN rail. For q38b-e.q312b-e, q612b, q38rb, q68rb, q65wrb, q38db, q312db. 4-axis, sscnet sub connected q26udvcpu parameter specification. 2-axis / 3-axis / 4-axis linear interpolation. 2-axis arc interpolation. Control unit: mm, inch, degree, pulse. Number of positioning data: 600 data / axis. 40 pin connector. Wiring is saved through sscnet sub cable connection, and the distance between stations can reach 50mq26udvcpu The q26udvcpu parameter specification of the position system that supports the determination of the origin position through the origin return data setting operation. In addition, the upper limit switch, lower limit switch and near point stop signal input can be directly connected to the servo amplifier, which greatly reduces the wiring demand. Easily realize high-speed positioning control. Support multiple types of positioning control, Including q26udvcpu parameter specifications such as 2-4-axis linear interpolation, 2-axis circular interpolation, speed control, speed / position switching control, path control, constant speed control, etc. In addition, software such as "GX configurator QP" can be used, It is convenient for positioning, setting, monitoring and debugging. RS-232 2ch。 The programmable controller can be programmed and monitored through the RS-232 serial communication programming tool of qj71c24n (- R2). Qj71c24n (- R2) has the function corresponding to the public telephone line modem. It can initialize the modem used and connect with the object device. Q26udvcpu (communication with built-in Ethernet port) communicates through remote equipment, programming tools, modems and public telephone lines. Using the remote password function, Access to the Q series PLC via the modem function of qj71c24n (- R2) can be blocked. Serial communication module q26udvcpu that can collect / change the data of programmable controller, monitor / manage the collection of measurement data, etc. (internal Ethernet port communication chapter). It can realize high-speed and high-capacity communication with high speed of 230.4kbps and large 960 words (in MC protocol communication). The MC protocol can be used to read / write data in the programmable controller through external devices (PC, display, etc.). By selecting the non sequential protocol and using the sequential program for communication control, between the programmable controller and the external equipment (bar code reader, measuring equipment, etc.), Use the local protocol of the external device to communicate with it q26udvcpu (Communication Chapter of built-in Ethernet port). Capacity: 8m bytes. Support SD memory card. High speed universal qcpu supports SD memory card, Thus, data exchange can be easily realized with PC with SD memory card socket. In addition, SD memory card and extended SRAM card can be used at the same time. Therefore, the extended SRAM card can be used to expand the file memory. The SD memory card can be used to record data files, save a large amount of annotation data, and guide the operation through the memory card at the same time. Better user experience data recording function. Easy to record without procedures. The collected data can be saved to the SD memory card in CSV format by simply completing the setting through the special configuration tool wizard, It can effectively use the saved CSV file to easily create various reference materials, Including daily report, generated report and general report q26udvcpu user manual. These data can be used for data analysis and traceability at startup, Just insert the SD memory card, and the q26udvcpu parameters and specifications can be recorded automatically. Just insert the SD memory card that saves the record setting file into the CPU to start recording automatically. Even when remote data collection is required, After receiving the record setting file by mail and storing it in the SD memory card, you can start recording immediately.

Minimum Order: 1 bags

Note: In order to prevent electric shock, the motor and frequency converter must be grounded before use. • Do not install the incoming capacitor or surge suppressor, radio noise filter to the output of the frequency converter. This will lead to the failure of the frequency converter or the damage of the capacitor and surge suppressor. If any of the above equipment has been installed, please remove it immediately. When it is necessary to set a non fuse circuit breaker at the output end, please consult the manufacturer for the selection of non fuse circuit breaker. • With regard to electromagnetic wave interference, the input / output (main circuit) of the frequency converter contains high-frequency components, which may interfere with the communication equipment near the frequency converter (such as AM radio). Therefore, EMC filters are installed to minimize interference. • For details of peripheral devices, please refer to the user manual of each option and peripheral device. • PM motor cannot operate on power frequency power supply. • Because PM motor is a motor with built-in permanent magnet, even when the power supply of frequency converter is disconnected, as long as the motor is still rotating, high voltage will be generated at the motor terminal. When the output switch is closed, turn on the power supply of the frequency converter and use it when the motor is stopped.

Minimum Order: 1 bags

New leakage circuit breaker Ew32 type ew63 type ew125 type ew160 type ew250 type ew400 type ew630 type EW800 type Ew50 type ew100 type Ew32 and ew50 (standard products) Basic models: ew32aag-2p, ew32aag-3p, ew32eag-3p Rated current a (code): 5 (005), 10 (010), 15 (015), 20 (020), 32 (032) Reaction current MA (code): 15 (a), 30 (b), 100 (c) Basic models: ew50aag-2p, ew50aag-3p, ew50eag-3p Rated current a (code): 5 (005) 10 (010) 15 (015) 20 (020) 32 (032) 40 (040) 50 (050) Reaction current MA (code): 15 (a), 30 (b), 100 (c) Note: ew50eag-3p reaction current MA (code): 15 (a) 30 (b) 100 / 200 switching (k) Basic model: ew32sag-3p Rated current a (code): 3 (003) 5 (005) 10 (010) 15 (015) 20 (020) 32 (032) Basic model: ew50sag-3p Rated current a (code): 5 (005) 10 (010) 15 (015) 20 (020) 32 (032) 40 (040) 50 (050) Basic model: ew50rag-3p Rated current a (code): 10 (010) 15 (015) 20 (020) 32 (032) 40 (040) 50 (050) Reaction current MA (code): 30 (b), 100 / 200 / 500 switching (k) Ew63 and ew100 (standard products) Basic model: ew63eag-3p Rated current a (code): 63 (063) Sensitivity current MA (code): 15 (a) 30 (b) 100 / 200 switching (k) Basic model: ew63sag-3p, ew63rag-3p Rated current a (code): 63 (063) Sensitivity current MA (code): 30 (b), 100 / 200 / 500 switching (k) Basic model: ew100aag-3p Rated current a (code): 63 (063) 75 (075) 100 (100) Sensitivity current MA (code): 30 (b) 100 / 200 switching (k) Basic model: ew100eag-2p Rated current a (code): 50 (050) 63 (063) 75 (075) 100 (100) Sensitivity current MA (code): 30 (b), 100 / 200 switching (k) Basic model: ew100eag-3p Rated current a (code): 50 (050) 63 (063) 75 (075) 100 (100) Sensitivity current MA (code): 30 (b), 100 / 200 / 500 switching (k) Ew125 (standard product) Basic models: ew125jagc-3p, ew125jagc-4p, ew125sagc-3p, ew125sagc-4p, ew125ragc-3p, ew125ragc-4p Rated current a (code): 15 (015) 20 (020) 32 (032) 40 (040) 50 (050) 63 (063) 75 (075) 100 (100) 125 (125) Reaction current MA (Code: 30 (b), 100 / 300 / 500 / 1000 switching (k) Ew160 (standard product) Basic models: ew160eagc-3p, ew160jagc-3p, ew160jagc-4p, ew160sagc-3p, ew160sagc-4p, ew160ragc- 3P,EW160RAGC-4P Rated current a (code): 125 (125) 150 (150) 160 (160) Reaction current MA (Code: 30 (b), 100 / 300 / 500 / 1000 switching (J) Ew250 (standard product) Basic models: ew250eagc-3p, ew250jagc-3p, ew250sagc-3p, ew250ragc-3p Rated current a (code): 175 (175) 200 (200) 225 (225) 250 (250) Reaction current MA (Code: 30 (b), 100 / 300 / 500 / 1000 switching (J) Basic models: ew250jagc-4p, ew250sagc-4p, ew250ragc-4p Rated current a (code): 175 (175) 200 (200) 225 (225) Reaction current MA (Code: 30 (b), 100 / 300 / 500 / 1000 switching (J) Ew400 (standard product) Basic models: ew400eagc-3p, ew400sagc-3p, ew400ragc-3p, ew400ragc-4p, ew400hagc-3p, ew400hagc-4p Rated current a (code): 250 (250) 300 (300) 350 (350) 400 (400) Reaction current MA (Code: 30 (b), 100 / 300 / 500 / 1000 switching (J) Ew600 (standard product) Basic models: ew630eagc-3p, ew630ragc-3p, ew630hagc-3p Rated current a (code): 500 (500), 630 (630) Reaction current MA (Code: 100 / 300 / 500 / 1000 switching (J) EW800 (standard product) Basic models: ew800eagc-3p, ew800ragc-3p, ew800hagc-3p Rated current a (code): 700 (700) 800 (800) Reaction current MA (Code: 100 / 300 / 500 / 1000 switching (J) New leakage circuit breaker Ew32 type ew63 type ew125 type ew160 type ew250 type ew400 type ew630 type EW800 type Ew50 type ew100 type Ew32 and ew50 (standard products) Basic models: ew32aag-2p, ew32aag-3p, ew32eag-3p Rated current a (code): 5 (005), 10 (010), 15 (015), 20 (020), 32 (032) Reaction current MA (code): 15 (a), 30 (b), 100 (c) Basic models: ew50aag-2p, ew50aag-3p, ew50eag-3p Rated current a (code): 5 (005) 10 (010) 15 (015) 20 (020) 32 (032) 40 (040) 50 (050) Reaction current MA (code): 15 (a), 30 (b), 100 (c) Note: ew50eag-3p reaction current MA (code): 15 (a) 30 (b) 100 / 200 switching (k) Basic model: ew32sag-3p Rated current a (code): 3 (003) 5 (005) 10 (010) 15 (015) 20 (020) 32 (032) Basic model: ew50sag-3p Rated current a (code): 5 (005) 10 (010) 15 (015) 20 (020) 32 (032) 40 (040) 50 (050) Basic model: ew50rag-3p Rated current a (code): 10 (010) 15 (015) 20 (020) 32 (032) 40 (040) 50 (050) Reaction current MA (code): 30 (b), 100 / 200 / 500 switching (k) Ew63 and ew100 (standard products) Basic model: ew63eag-3p Rated current a (code): 63 (063) Sensitivity current MA (code): 15 (a) 30 (b) 100 / 200 switching (k) Basic model: ew63sag-3p, ew63rag-3p Rated current a (code): 63 (063) Sensitivity current MA (code): 30 (b), 100 / 200 / 500 switching (k) Basic model: ew100aag-3p Rated current a (code): 63 (063) 75 (075) 100 (100) Sensitivity current MA (code): 30 (b) 100 / 200 switching (k) Basic model: ew100eag-2p Rated current a (code): 50 (050) 63 (063) 75 (075) 100 (100) Sensitivity current MA (code): 30 (b), 100 / 200 switching (k) Basic model: ew100eag-3p Rated current a (code): 50 (050) 63 (063) 75 (075) 100 (100) Sensitivity current MA (code): 30 (b), 100 / 200 / 500 switching (k) Ew125 (standard product) Basic models: ew125jagc-3p, ew125jagc-4p, ew125sagc-3p, ew125sagc-4p, ew125ragc-3p, ew125ragc-4p Rated current a (code): 15 (015) 20 (020) 32 (032) 40 (040) 50 (050) 63 (063) 75 (075) 100 (100) 125 (125) Reaction current MA (Code: 30 (b), 100 / 300 / 500 / 1000 switching (k) Ew160 (standard product) Basic models: ew160eagc-3p, ew160jagc-3p, ew160jagc-4p, ew160sagc-3p, ew160sagc-4p, ew160ragc- 3P,EW160RAGC-4P Rated current a (code): 125 (125) 150 (150) 160 (160) Reaction current MA (Code: 30 (b), 100 / 300 / 500 / 1000 switching (J) Ew250 (standard product) Basic models: ew250eagc-3p, ew250jagc-3p, ew250sagc-3p, ew250ragc-3p Rated current a (code): 175 (175) 200 (200) 225 (225) 250 (250) Reaction current MA (Code: 30 (b), 100 / 300 / 500 / 1000 switching (J) Basic models: ew250jagc-4p, ew250sagc-4p, ew250ragc-4p Rated current a (code): 175 (175) 200 (200) 225 (225) Reaction current MA (Code: 30 (b), 100 / 300 / 500 / 1000 switching (J) Ew400 (standard product) Basic models: ew400eagc-3p, ew400sagc-3p, ew400ragc-3p, ew400ragc-4p, ew400hagc-3p, ew400hagc-4p Rated current a (code): 250 (250) 300 (300) 350 (350) 400 (400) Reaction current MA (Code: 30 (b), 100 / 300 / 500 / 1000 switching (J) Ew600 (standard product) Basic models: ew630eagc-3p, ew630ragc-3p, ew630hagc-3p Rated current a (code): 500 (500), 630 (630) Reaction current MA (Code: 100 / 300 / 500 / 1000 switching (J) EW800 (standard product) Basic models: ew800eagc-3p, ew800ragc-3p, ew800hagc-3p Rated current a (code): 700 (700) 800 (800) Reaction current MA (Code: 100 / 300 / 500 / 1000 switching (J)

Minimum Order: 1 bags

DC reactor, also known as smoothing reactor, is mainly used on the DC side of converter and is widely used in general frequency converter. There is a DC current with AC component flowing through the reactor. The main purpose is to limit the AC component superimposed on the DC current to a specified value, keep the rectifier current continuous, reduce the current ripple value, improve the input power factor, and suppress the harmonic generated by the converter. effect DC reactors are connected in series on each pole of the converter station. The inductance is about 0.4 ~ 1.0h. Its main functions are as follows: (1) Prevent inverter commutation failure. (2) Reduce voltage and current harmonics in DC lines. (3) Reduce ripple coefficient. (4) Limit the current in the rectifier when the line is short circuited. However, it should be noted that the value of inductance must ensure that the DC circuit does not resonate at power frequency. DC reactor can increase the power factor to more than 0.9. Because of its small size, many frequency converters have installed DC reactors directly in the frequency converter. In addition to improving the power factor, the DC reactor can also weaken the impact at the moment when the power supply is just connected. If AC reactor and DC reactor are equipped at the same time, the power factor of variable frequency speed regulation system can be increased to more than 0.95. Structural design The DC smoothing reactor is used for the filter circuit at the output side of the rectifier circuit. Because there is a DC current component, the magnetic flux of the iron core works in the first quadrant, resulting in magnetic bias. In order to increase the inductance and prevent magnetic flux saturation, DC smoothing reactors adopt cut iron core and add air gap to lengthen their hysteresis loop laterally, which is a bit like the case of single ended flyback transformer in principle. In this way, when there is a current of the same size, B is small and not easy to be saturated. Four factors should be considered in the structural design of open core reactor: 1) The DC component I of the current flowing through the reactor, that is, the average value of the inductive current IL, determines the cross-sectional area of the winding conductor and the heating of the winding. 2) The peak to peak value of AC current component is expressed by △ IPP or abbreviated as △ I, which is determined by the continuity requirements of inductive current. Generally, without affecting the output voltage ripple, twice the minimum load current ilmin output by the rectifier filter circuit is the peak to peak of the required filter inductance current change. Thus: △ IPP = 2ilmin 3) The inductance L required by the filter circuit is determined by the frequency of AC current component and peak to peak △ IPP. It is an intermediate calculated value in the process of reactor structure design, rather than the primary factor to be considered in advance. 4) Power loss and temperature rise are factors that need to be considered in advance in the process of reactor structure design. There are more than one method to design DC smoothing reactor, and these methods are unified with each other. A simple, clear and practical engineering design method is introduced here. Its steps are as follows: (1) Calculated energy storage We know that if the inductance of the reactor is l and the current is I, the stored energy is W=1/2LI Because the highest flux density BM is determined by the maximum current in the reactor, I in the formula should be calculated according to the maximum current. If the DC current is I, the peak to peak value of AC current is △ IPP. (2) Select the material of iron core According to the proportion of AC component △ I in I, the frequency of AC component and the index requirements of inverter on its output noise, the material of reactor core can be selected. After the material is selected, the maximum flux density BM and the effective coefficient K of iron core section can be determined. Note that when selecting BM, it is generally required to leave a large margin, because the reactor is not saturated after half an inverter cycle of output short circuit (i.e. a normal rectifier cycle), so as to make the protection circuit act, so as to improve the working reliability of the inverter circuit. (3) Select the shape of the iron core and determine the window utilization coefficient KC According to the material, winding process and installation structure of the selected iron core, the shape of the iron core is selected, and then the type of conductor is selected according to the current level to determine the window utilization coefficient KC. (4) Select conductor current density coefficient kJ and current density J According to the heat dissipation conditions, the required copper consumption, the shape of the iron core and the allowable temperature rise of the wire package, select the appropriate current density coefficient kJ (refer to table 4.2) and the current density J of the conductor. (5) Calculate the cross-sectional area of the wire and select the wire The cross-sectional area of the conductor is calculated by the following formula: S = I / J; Then select the shape and size of the wire. (6) Calculate the number of winding turns When calculating the number of turns of reactor winding, we should consider making full use of the window area of iron core, so as to maximize the number of turns and leave a certain margin for BM. N=A·Kc/S

Minimum Order: 1 bags

Proximity switches are widely used in aviation, aerospace technology and industrial production. It is used in daily life, such as automatic doors in hotels, restaurants and garages and automatic hot air fans. In terms of security and anti-theft, important places such as data archives, finance and accounting, finance, museums and treasuries are usually equipped with anti- theft devices composed of various proximity switches. In measurement technology, such as length and position measurement; In the control technology, such as the measurement and control of displacement, velocity and acceleration, a large number of proximity switches are also used. Ime08-1b5pszt0s Order No.: 1040838 inductive proximity sensor Trigger sensing distance SN: 1.5 mm Mounting on metal: flush Shell shape: Standard Electrical specification: DC 3-wire Switching value output: PNP Switch function: normally open contact Connection type: plug, M8, 3-pin E3X-DA11-N Type: e3x-da11-n Order No.: 1040854 inductive proximity sensor Trigger sensing distance SN: 2.5 mm Mounting on metal: non flush Shell shape: Standard Electrical specification: DC 3-wire Switching value output: PNP Switch function: normally open contact Connection type: plug, M8, 3-pin E3X-DA11-N Type: e3x-da11-n Order No.: 1040837 inductive proximity sensor Trigger sensing distance SN: 1.5 mm Wiring diagram of proximity switch 1) Proximity switch has the difference between two-wire system and three wire system. Three wire proximity switch is divided into NPN type and PNP type, and their wiring is different. See the figure below: 2) The wiring of the two-wire proximity switch is relatively simple. The proximity switch can be connected to the power supply after being connected in series with the load. 3) Wiring of three wire proximity switch: the red (brown) wire is connected to the positive end of the power supply; The blue line is connected to the 0V end of the power supply; The yellow (black) line is a signal and should be connected to the load. The other end of the load is connected in this way: for NPN proximity switch, it should be connected to the positive end of the power supply; For PNP type proximity switch, it shall be connected to the 0V end of the power supply. 4) The load of proximity switch can be signal lamp, relay coil or digital input module of PLC. 5) Special attention should be paid to the type selection of three wire proximity switch connected to PLC digital input module. PLC digital input modules can generally be divided into two types: one type of common input terminal is the power supply 0V, and the current flows out of the input module (Japanese mode). At this time, NPN proximity switch must be selected; The other type of common input is the positive end of the power supply, and the current flows into the input module, i.e. well input (European mode). At this time, PNP type proximity switch must be selected. Don't make a mistake. 6) The two-wire proximity switch is limited by the working conditions. When it is turned on, the switch itself produces a certain voltage drop, and when it is cut off, there is a certain residual current flowing. It should be considered when selecting. Although the three wire proximity switch has one more wire, it is not troubled by adverse factors such as residual current and works more reliably. 7) Some manufacturers lead out the "normally open" and "normally closed" signals of the proximity switch at the same time, or add other functions. In this case, please make specific wiring according to the product manual. Slot type photoelectric switch wiring The diode of the photoelectric switch is a light-emitting diode, the output is a photosensitive triode, C is the collector, and E is the emitter. When a triode is used as a switch, the collector is usually used as the output. General connection method: the diode is the input end, e is grounded, C is connected to the load, and the other end of the load needs to be connected to the positive power supply. This connection method has a wide range of application. Special connection method: the diode is the input end, C is connected to the positive power supply, e is connected to the load, and the other end of the load needs to be grounded. This connection method is only applicable when the load equivalent resistance is very small (within tens of ohms). If the load equivalent resistance is relatively large, the working point of the switching triode may be abnormal, resulting in unreliable switching operation. In general industrial production sites, eddy current proximity switches and capacitive proximity switches are usually selected. Because these two proximity switches have low requirements for the environment. When the measured object is a conductive object or an object that can be fixed on a metal object, eddy current proximity switch is generally selected because of its high response frequency, good anti-environmental interference performance, wide application range and low price. If the measured object is non-metal (or metal), liquid level height, powder height, plastic, tobacco, etc. Capacitive proximity switch shall be selected. This kind of switch has low response frequency but good stability. The influence of environmental factors shall be considered during installation. If the measured object is made of magnetic conducting material or the magnetic steel is buried in the measured object in order to distinguish the object moving with it, hall proximity switch shall be selected, and its price is the lowest. Photoelectric proximity switches can be used in occasions with good environmental conditions and no dust pollution. When the photoelectric proximity switch works, it has almost no effect on the measured object. Therefore, it is widely used in fax machines with high requirements and tobacco machinery. In the anti-theft system, the automatic door usually uses pyroelectric proximity switch, ultrasonic proximity switch and microwave proximity switch. Sometimes, in order to improve the reliability of identification, the above proximity switches are often used in combination.

Minimum Order: 1 bags

Contactors are divided into AC contactors (voltage AC) and DC contactors (voltage DC), which are used in power, power distribution and power consumption. Broadly speaking, contactor refers to an electrical appliance that uses the current flowing through the coil to generate a magnetic field and close the contact in order to control the load. main features The AC contactor uses the main contact to open and close the circuit and the auxiliary contact to turn on the control circuit. The main contact is generally normally open contact, while the auxiliary contact often has two pairs of normally open contact and normally closed contact. Small contactors are often used as intermediate relays to cooperate with the main circuit. The contact of AC contactor is made of silver tungsten alloy, which has good conductivity and high temperature ablation resistance. The power of AC contactor action comes from the magnetic field generated by AC through the coil with iron core. The electromagnet core is composed of two "mountain" shaped young silicon steel sheets. One of the fixed iron core is sleeved with coil, and the working voltage can be selected. In order to stabilize the magnetic force, a short-circuit ring is added to the suction surface of the iron core. After the AC contactor loses power, it returns by spring. The other half is a movable iron core, whose structure is the same as that of a fixed iron core, which is used to drive the closing and breaking of the main contact and auxiliary contact. Contactors above 20 amps are equipped with arc extinguishing cover, which can quickly break the arc and protect the contact by using the electromagnetic force generated when the circuit is disconnected. The contactor can operate at high frequency. When it is used as the power on and off control, the maximum operation frequency can reach 1200 times per hour. The service life of contactors is very long. The mechanical life is usually millions to 10 million times, and the electrical life is generally hundreds of thousands to millions of times. working principle The working principle of the contactor is: when the contactor coil is energized, the coil current will generate a magnetic field. The generated magnetic field causes the static iron core to generate electromagnetic suction to attract the moving iron core, and drives the AC contactor to act. The normally closed contact is disconnected and the normally open contact is closed. The two are linked. When the coil is powered off, the electromagnetic suction disappears, and the armature is released under the action of the release spring to restore the contact, open the normally open contact and close the normally closed contact. The working principle of DC contactor is a little similar to that of temperature switch.

Minimum Order: 1 bags

FUJI AA84030 NXT I 8MM W8 FUJI AA84128 NXT I 12MM W12 FUJI AA84228 NXT I 16MM W16 FUJI AA84328 NXT I 24MM W24 FUJI AA84426 NXT I 32MM W32 FUJI AA84525 NXT I 44MM W44 FUJI AA84625 NXT I 56MM W56 FUJI AA2GZ03 NXT I 72MM W72 FUJI AA2HA03 NXT I 88MM W88 FUJI AB09910 NXT II 8MM W08C FUJI AB10005 NXT II 12MM W12C FUJI AB10105 NXT II 16MM W16C FUJI AB10205 NXT II 24MM W24C FUJI AB10303 NXT II 32MM W32C FUJI AB10403 NXT II 44MM W44C FUJI AB10503 NXT II 56MM W56C Shenzhen Peishang Trading Co., Ltd operates the following SMT products: 1. SMT equipment and accessories: suction nozzle, feeder, feeder parts, scraper, filter, guide rails, tapes, air cylinder, belt, smt grease/lubricants, sensor, etc. 2. Nozzle and feeder for Fuji, Juki, Yamaha, Samsung, Siemens, PanasonicCM602, CM402... have a large stock. 3. Nozzle cleaning machine, solder paste mixer, SMD component counter Provide complete SMT assembly line solutions, including SMT reflow oven, wave soldering machine, placement machine, SMT stencil printer, SMT AOI SPI machine, SMT reflow oven, SMT peripheral equipment, SMT assembly line, SMT spare parts, etc. Any type of SMT machines you may need, Our advantage A. Has a team of engineers with more than 10 years of SMT service experience. B. Various brands to choose from C. Provide customized services D. Large inventory - more than 10000 models of smt parts If there is no matching model, please contact us directly! Please contact us for more information: WeChat whatsapp: +8613662569408, Email: nancy@pshang-smt.com

Minimum Order: 1 bags

Contact :Sandy Lin Email : unity@mvme.cn Skype: onlywnn_1 Mob/Whatsapp : +86 18020776786 Wechat : mooreplc website : https://www.dcsmodule.com General Specification BENEFITS:(I WILL GIVE YOU A REPLY IMMEDIATELY) Quantity available: 1  The colour：NEW Warranty: 12 months. Lead time: 1-2 working days. Terms of payment: Paypal、T/T 、 Western Union. Courier partners: DHL, UPS, TNT, FedEx and EMS. Technical specification, manuals and data sheets Company Profile We have a large inventory of spare parts for industrial control systems. Manufacturers cover a wide range and also work with a wide range of suppliers. Fast shipping to provide you with the best solution to meet your urgent needs If we don't have the stock request quotation you need, we can usually find it for you. Moore Automation also offers quality outdated/discontinued spare parts to extend the installed life of your installed control system and reduce maintenance costs. Specializing In: -Control Systems (DCS, PLC, CNC) -Panel Controllers -HMI and Display Panels -Drives -Servo Motors -Encoders and Resolvers -Power Supplies Recommend Products Allen Bradley 1794-IB16XOB16P Schneider 171CCC96030 Allen Bradley 1746-NI8 SIEMENS 6ES7953-8LG31-0AA0 GE IC200MDL241 Danaher S70601 ABB PM864AK01 3BSE018161R1 SIEMENS 6EP1332-2BA20 SIEMENS 6DD1661-0AB1 EPRO PR6423/011-000 DIGITRONIC 1756-DICAM ABB AI635 3BHT300032R1 ABB ACS355-03E-07A3-4 ABB SDCS-PIN-3B GE IC695ALG628 WESTINGHOUSE 1C31219G01 SIEMENS 6RA7078-6DV62-0

Minimum Order: 1 bags

Contact :Sandy Lin Email : unity@mvme.cn Skype: onlywnn_1 Mob/Whatsapp : +86 18020776786 Wechat : mooreplc website : https://www.dcsmodule.com General Specification BENEFITS:(I WILL GIVE YOU A REPLY IMMEDIATELY) Quantity available: 1  The colour：NEW Warranty: 12 months. Lead time: 1-2 working days. Terms of payment: Paypal、T/T 、 Western Union. Courier partners: DHL, UPS, TNT, FedEx and EMS. Technical specification, manuals and data sheets Company Profile We have a large inventory of spare parts for industrial control systems. Manufacturers cover a wide range and also work with a wide range of suppliers. Fast shipping to provide you with the best solution to meet your urgent needs If we don't have the stock request quotation you need, we can usually find it for you. Moore Automation also offers quality outdated/discontinued spare parts to extend the installed life of your installed control system and reduce maintenance costs. Specializing In: -Control Systems (DCS, PLC, CNC) -Panel Controllers -HMI and Display Panels -Drives -Servo Motors -Encoders and Resolvers -Power Supplies Recommend Products Allen Bradley 1794-IB16XOB16P Schneider 171CCC96030 Allen Bradley 1746-NI8 SIEMENS 6ES7953-8LG31-0AA0 GE IC200MDL241 Danaher S70601 ABB PM864AK01 3BSE018161R1 SIEMENS 6EP1332-2BA20 SIEMENS 6DD1661-0AB1 EPRO PR6423/011-000 DIGITRONIC 1756-DICAM ABB AI635 3BHT300032R1 ABB ACS355-03E-07A3-4 ABB SDCS-PIN-3B GE IC695ALG628 WESTINGHOUSE 1C31219G01 SIEMENS 6RA7078-6DV62-0

Minimum Order: 1 bags

Contact :Sandy Lin Email : unity@mvme.cn Skype: onlywnn_1 Mob/Whatsapp : +86 18020776786 Wechat : mooreplc website : https://www.dcsmodule.com General Specification BENEFITS:(I WILL GIVE YOU A REPLY IMMEDIATELY) Quantity available: 1  The colour：NEW Warranty: 12 months. Lead time: 1-2 working days. Terms of payment: Paypal、T/T 、 Western Union. Courier partners: DHL, UPS, TNT, FedEx and EMS. Technical specification, manuals and data sheets Company Profile We have a large inventory of spare parts for industrial control systems. Manufacturers cover a wide range and also work with a wide range of suppliers. Fast shipping to provide you with the best solution to meet your urgent needs If we don't have the stock request quotation you need, we can usually find it for you. Moore Automation also offers quality outdated/discontinued spare parts to extend the installed life of your installed control system and reduce maintenance costs. Specializing In: -Control Systems (DCS, PLC, CNC) -Panel Controllers -HMI and Display Panels -Drives -Servo Motors -Encoders and Resolvers -Power Supplies Recommend Products Allen Bradley 1794-IB16XOB16P Schneider 171CCC96030 Allen Bradley 1746-NI8 SIEMENS 6ES7953-8LG31-0AA0 GE IC200MDL241 Danaher S70601 ABB PM864AK01 3BSE018161R1 SIEMENS 6EP1332-2BA20 SIEMENS 6DD1661-0AB1 EPRO PR6423/011-000 DIGITRONIC 1756-DICAM ABB AI635 3BHT300032R1 ABB ACS355-03E-07A3-4 ABB SDCS-PIN-3B GE IC695ALG628 WESTINGHOUSE 1C31219G01 SIEMENS 6RA7078-6DV62-0

Minimum Order: 1 bags

Contact :Sandy Lin Email : unity@mvme.cn Skype: onlywnn_1 Mob/Whatsapp : +86 18020776786 Wechat : mooreplc website : https://www.dcsmodule.com General Specification BENEFITS:(I WILL GIVE YOU A REPLY IMMEDIATELY) Quantity available: 1  The colour：NEW Warranty: 12 months. Lead time: 1-2 working days. Terms of payment: Paypal、T/T 、 Western Union. Courier partners: DHL, UPS, TNT, FedEx and EMS. Technical specification, manuals and data sheets Company Profile We have a large inventory of spare parts for industrial control systems. Manufacturers cover a wide range and also work with a wide range of suppliers. Fast shipping to provide you with the best solution to meet your urgent needs If we don't have the stock request quotation you need, we can usually find it for you. Moore Automation also offers quality outdated/discontinued spare parts to extend the installed life of your installed control system and reduce maintenance costs. Specializing In: -Control Systems (DCS, PLC, CNC) -Panel Controllers -HMI and Display Panels -Drives -Servo Motors -Encoders and Resolvers -Power Supplies Recommend Products Allen Bradley 1794-IB16XOB16P Schneider 171CCC96030 Allen Bradley 1746-NI8 SIEMENS 6ES7953-8LG31-0AA0 GE IC200MDL241 Danaher S70601 ABB PM864AK01 3BSE018161R1 SIEMENS 6EP1332-2BA20 SIEMENS 6DD1661-0AB1 EPRO PR6423/011-000 DIGITRONIC 1756-DICAM ABB AI635 3BHT300032R1 ABB ACS355-03E-07A3-4 ABB SDCS-PIN-3B GE IC695ALG628 WESTINGHOUSE 1C31219G01 SIEMENS 6RA7078-6DV62-0

Minimum Order: 1 bags