Power Supplies & Equipment

Brand: Mitsubishi Product Name: servo drive model: mr-j4-200b1 axis servo amplifier. Mitsubishi universal AC servo amplifier melcervo-j4 series. Rated output: 2.0kw. Interface: sscnet Ⅲ / h power supply: three-phase ac200v. The same service amplifier supporting sscneti / h. A fully synchronous system using high-speed serial optical communication can be established. It can be combined with servo system controller to maximize the functional performance of servo system. At the same time, it can support the anti-seismic algorithm at 3 places of inertia equipment. Mr configurator2 enables easy adjustment. The low-frequency aftershock effect below 100Hz produced by the front end of the boom or the main body of the device is effectively. It can effectively shorten the time required for aftershock control. The accuracy of arc trajectory can be improved in the trajectory control of XY slide. At the same time, it can help to control the quadrant real up phenomenon caused by the rotation direction of the same service application machine due to rate friction and distortion. Servo motor series: medium inertia, small capacity. Rated output: 4.2kW. Rated speed: 1000r / min. electromagnetic braking: without. Power supply: 200V. Realize the stable driving of medium capacity and medium inertia products. Mitsubishi mr-j4-200b realizes the small total length in the industry through optimized structural design. High speed & high torque, shorten positioning time, realize high-speed equipment and reduce Tongshen torque ripple. By optimizing the combination of motor poles and slots, Tongshen torque ripple is greatly reduced. Further realize the smooth and constant speed operation of the equipment mr-j4-200b To improve the environmental resistance, hg-sr and hg-jr series products adopt IP67. Motor series: low inertia and medium capacity. Rated output power: 37.0kw. Rated speed: 2000rom With or without holding room: without Mitsubishi mr-j4-200b Voltage: 400V level. Shaft end: straight shaft. Brushless motor has the advantages of small volume, light weight, large output, fast response, high speed, small inertia, smooth rotation, stable torque, complex control, easy to realize intellectualization, flexible electronic commutation mode, square wave commutation or bottom chord wave commutation. The motor is maintenance free, with high efficiency, low operating temperature, low electromagnetic radiation and long service life. It can be used in various environments. AC servo motor is also a brushless motor, which is divided into synchronous motor and asynchronous motor. At present, synchronous motor is generally used in motion control. It has a large power range and can achieve great power Mitsubishi mr-j4-200b. Large inertia, high rotational speed, low, and rapidly decreases with the increase of power. Therefore, it is suitable for the application of low-speed and smooth operation, driving unit= Mitsubishi universal AC servo amplifier melcervo-j4 series. Rated output: 37KW three ginger servo driver. Interface: universal. Power supply: three-phase AC400V. Special specification: totally enclosed control 4-wire / support mechanical end encoder ABZ phase input / support positioning mode. Support position control, speed control and torque control. The position control follows the position command for positioning. When using synchronization control and insertion control, perform position control Speed control follows the speed command to control the speed within a certain range, Torque control is to follow the torque command to control the stable torque servo driver. Switchable function. It can switch the increase during rotation and stop, The switching signal is used to switch the amplitude during operation. Servo motor series: medium inertia, medium power. Rated output: 2.0kw. Rated speed: 2000r / min, Electromagnetic brake: with Mitsubishi servo driver. Shaft end specification: Standard (straight shaft). Features: medium inertia has two types: low speed and high speed, which are suitable for different applications. IP rating: IP67. Application example: 1. Material conveying system. 2. Industrial robots. 3. X-Y workbench. The protection grade of hf-sp / hf-jp series motor in the same suit is IP67 (excluding the shaft through part). The motor capacity is soft (mrzjw3- motsz111e) Friendly interface design, just input the constant and operation mode in the mechanical description window to select Jiajia servo amplifier. Servo motor and regenerative braking options. You can also select the features of linear servo motor and direct drive motor mr-j4-200b in the selection window (1) 10 kinds of curved mechanical transmission structures are available (2) The user-defined operation mode (position and speed control mode) can be set. (3) in the selection process, the feed speed and torque can be displayed in chart format. (4) the calculation process can be displayed

Minimum Order: 1 bags

1-axis servo amplifier. Mitsubishi universal AC servo amplifier melcervo-j4 series. Rated output: 0.1kw. Interface: sscnet Ⅲ / h. Power supply: single phase AC100V power supply Only for servo amplifiers below 0.4KW, Mitsubishi PLC and servo. Special specifications: CC linkle is supported Field network motion control supports the co server amplifier of CC linkle field network. Ethernet based open network, supporting motion control mr-j4-350b It not only inherits the high performance and high reliability of the original products, but also makes further improvements beyond imagination, Mitsubishi PC and servo. Melcervo-j4 weight reduction debut. The future star of the same service market. World class servo products, What should the new generation of melcervo be like? The answer to the question has floated Out of the water. Melcervo-j4... It represents another evolution based on the original high performance after full digitization. It is also the latest masterpiece of melcervo, which fully meets the requirements of human and environment. For example, the safety specification and "easy to use" design for human use safety and environmental protection. Energy saving performance to meet the needs of the era of environmental protection. Melcervo-j4, the evolution of zhaoyue performance, is shocking! 1 axis co serving amplifier. A Tonga AC co service amplifier melcervo-j4 series. Rated output: 11.0kwmr-j4-350b. Interface: sscnet Ⅲ / h. Power supply: three-phase ac200v. Servo amplifier supporting sscnet / h. A fully synchronous system using high-speed serial optical communication can be established. It can be combined with servo system controller to maximize the functional performance of servo system and improve mechanical performance through high- performance motor. By improving the resolution and processing speed of the encoder, Make the rotary servo motor have higher precision positioning performance and smoother rotation performance mr-j4-350b. Just turn on the one click adjustment function to adjust the servo gain including mechanical resonance wave pusher, high-end seismic control II and low-pass filter. Easily start the advanced anti-seismic function to maximize the mechanical performance. And it can automatically implement the response setting required for real-time automatic adjustment. Mr-j4-350b, cable length: 3M, (dry mr-j2s -- CP (1) - s084) For mr-j2s-11ka (4) to mr-j2s-22ka (4). Cable length: 10M. Dry mr-j2s-700a (4) / CP / CL or less Encoder for hc-sfs; HC-LFS; HC-RFS; HC-UFS2000r/min; Ha-lfs servo motor- L represents bending life, mr-j2m multi axis servo amplifier extension unit. 1. The servo controller can easily convert the operation module and Fieldbus module through the automation interface, At the same time, different fieldbus modules are used to realize different control modes (RS232, RS485, optical fiber, INTERBUS, PROFIBUS). The control mode of general frequency converter is relatively single. 2. The servo controller is directly connected with the resolver or encoder to form a closed loop of speed and displacement control. The general frequency converter can only form an open-loop control system. 3. The control indexes of servo controller (such as steady-state accuracy and dynamic performance) are better than general frequency converter. 1-axis servo amplifier. Yiling general AC servo amplifier melcervo-j4 series. 1-axis servo amplifier. Mitsubishi universal AC servo amplifier melcervo-j4 series. Rated output: 0.1kw. Interface: sscnet Ⅲ / h. Power supply: single phase AC100V power supply Only for servo amplifiers below 0.4KW, Mitsubishi PLC and servo. Special specifications: CC linkle is supported Field network motion control supports the co server amplifier of CC linkle field network. Ethernet based open network, supporting motion control mr-j4-350b It not only inherits the high performance and high reliability of the original products, but also makes further improvements beyond imagination, Mitsubishi PC and servo. Melcervo-j4 weight reduction debut. The future star of the same service market. World class servo products, What should the new generation of melcervo be like? The answer to the question has floated Out of the water. Melcervo-j4... It represents another evolution based on the original high performance after full digitization. It is also the latest masterpiece of melcervo, which fully meets the requirements of human and environment. For example, the safety specification and "easy to use" design for human use safety and environmental protection. Energy saving performance to meet the needs of the era of environmental protection. Melcervo-j4, the evolution of zhaoyue performance, is shocking! 1 axis co serving amplifier. A Tonga AC co service amplifier melcervo-j4 series. Rated output: 11.0kwmr-j4-350b. Interface: sscnet Ⅲ / h. Power supply: three-phase ac200v. Servo amplifier supporting sscnet / h. A fully synchronous system using high-speed serial optical communication can be established. It can be combined with servo system controller to maximize the functional performance of servo system and improve mechanical performance through high- performance motor. By improving the resolution and processing speed of the encoder, Make the rotary servo motor have higher precision positioning performance and smoother rotation performance mr-j4-350b. Just turn on the one click adjustment function to adjust the servo gain including mechanical resonance wave pusher, high-end seismic control II and low-pass filter. Easily start the advanced anti-seismic function to maximize the mechanical performance. And it can automatically implement the response setting required for real-time automatic adjustment. Mr-j4-350b, cable length: 3M, (dry mr-j2s -- CP (1) - s084) For mr-j2s-11ka (4) to mr-j2s-22ka (4). Cable length: 10M. Dry mr-j2s-700a (4) / CP / CL or less Encoder for hc-sfs; HC-LFS; HC-RFS; HC-UFS2000r/min; Ha-lfs servo motor- L represents bending life, mr-j2m multi axis servo amplifier extension unit. 1. The servo controller can easily convert the operation module and Fieldbus module through the automation interface, At the same time, different fieldbus modules are used to realize different control modes (RS232, RS485, optical fiber, INTERBUS, PROFIBUS). The control mode of general frequency converter is relatively single. 2. The servo controller is directly connected with the resolver or encoder to form a closed loop of speed and displacement control. The general frequency converter can only form an open-loop control system. 3. The control indexes of servo controller (such as steady-state accuracy and dynamic performance) are better than general frequency converter. 1-axis servo amplifier. Yiling general AC servo amplifier melcervo-j4 series.

Minimum Order: 1 bags

Mitsubishi q series universal high speed CPU module q03udvcpu product specification [control mode] stored program repeat operation [input / output control mode] refresh mode (input / output of direct access mode can be carried out by specifying direct access mode input / output (DX □, Dy □)) [program language (sequence control program control language)] relay symbol language, logic symbol language, melsap3 (SFC), melsap-l, function block, structured text (st) [processing speed (sequence control program instruction)] LD x0 1.9ns; MOV D0 D1 3.9ns [constant scanning (function for keeping scanning time constant)] 0.5 ~ 2000ms (can be set in 0.1ms) (according to parameter setting) [program capacity] 30K steps (120K bytes) [memory capacity] . program memory (drive 0): 120K bytes . memory card (SD) (drive 2): the capacity of SD memory card (SD / SDHC) that can be installed (up to 32g bytes) . standard RAM (drive 3) When the extended SRAM cartridge is not used: 192K bytes When using extended SRAM cartridge: capacity when not using extended SRAM cartridge + capacity of extended SRAM cartridge (maximum 8m bytes of extended SRAM cartridge) . standard ROM (drive 4): 1025.5k bytes . CPU shared memory: 8K bytes High speed communication area between multiple CPUs: 32K bytes [maximum number of stored files] . program memory: 124 . memory card (SD) SD: 512 root folders and 65534 subdirectories at most SDHC: 65535 root folders and 65534 subdirectories at most . standard ram: 323 when using / not using the extended SRAM card box . standard ROM: 256 [maximum number of intelligent function module parameters] initial setting 4096, 2048 when refreshing [write times of program memory] 100000 times at most [number of writes to standard ROM] up to 100000 times [number of input and output software components (number of points can be used in the program)] 8192 points (x / Y0 ~ 1fff) [I / O points (accessible points of actual I / O module)] 4096 points (x / Y0 ~ FFF) [specification of built-in Ethernet port of CPU] . data transmission speed: 100 / 10Mbps . communication mode: full duplex / half duplex . transmission method: baseband . maximum distance between hub and node: 100M . maximum number of nodes / connections: up to 4 levels for 10Base-T series connection and up to 2 levels for 100base-tx series connection . number of connections: 16 socket communication, melsoft connection and MC protocol in total, 1 for FTP [latch (hold point) range] l0 ~ 8191 (default value: 8192 points) (the latch range can be set for B, F, V, t, St, C, D and W) (set through parameters) [run / pause contact] one point of run / pause contact can be set in x0 ~ 1fff (through parameter setting) [allowable instantaneous stop time] 0.58a (CPU module body) / 0.6A (when installing extended SRAM card box) [overall dimension h * w * D] 98 * 27.4 * 115mm [weight] 0.2kg

Minimum Order: 1 bags

The power supply module is a power supply that can be directly mounted on the printed circuit board. It is characterized by providing power supply for integrated circuit (ASIC), digital signal processor (DSP), microprocessor, memory, field programmable gate array (FPGA) and other digital or analog loads. Generally speaking, such modules are called point of load (POL) power supply system or point of use power supply system (pups). Due to the advantages of modular structure, modular power supply is widely used in switching equipment, access equipment, mobile communication, microwave communication, optical transmission, router and other communication fields, automotive electronics, aerospace and so on. Mitsubishi Q61P is the power module of Mitsubishi q series PLC. The power module is a module that provides DC5V power to each module of the programmable controller installed on the base plate. Qy61p parameters: Q61p-a1 input voltage range: AC100 ~ 240V output voltage: DC5V output current: 6A Mitsubishi Q61P details: Mitsubishi Q61P is a power module. PLC power supply is used to provide working power for the integrated circuit of each PLC module. At the same time, some also provide 24V working power supply for the input circuit. Power input types include: AC power supply (220VAC or 110VAC), DC power supply (24VAC is commonly used). Most modular PLCs use backplane or rack. Its function is to realize the connection between modules electrically, so that the CPU can access all modules on the backplane, and mechanically, realize the connection between modules, so that each module forms a whole. Other equipment of PLC system: 1. Programming equipment: the programmer is an indispensable device for PLC development and application, monitoring operation, inspection and maintenance. It is used to write programs, make some settings for the system, and monitor the working conditions of PLC and the system controlled by PLC, but it does not directly participate in the on-site control operation. Some PLCs are also equipped with handheld programmers. At present, computers (running programming software) generally act as programmers. 2. Man machine interface: the simplest man-machine interface is indicator light and button. At present, LCD (or touch screen) integrated operator terminal is more and more widely used, and computer (running configuration software) is also very popular as man-machine interface. 3. Input and output equipment: used to permanently store user data, such as EPROM, EEPROM writer, bar code reader, potentiometer for inputting analog quantity, printer, etc.

Minimum Order: 1 bags

Three phase three wire type. Number of measuring circuits: 1 circuit. Measurement items: power consumption (consumption and regeneration), current, voltage, power, power factor, etc. it is a product group of elevtric energy measurement modules that can simply measure a variety of energy information. With only one module, you can measure various detailed information related to power (consumption and regeneration), reactive power, current, voltage, power, power factor and frequency. Mitsubishi 1 / O module user manual. The minimum and maximum values can be continuously monitored without ladder program, and two types of upper / lower limit alarm qh42f can be executed. The power used by the output device can be measured only during the on state. Therefore, the power during the operation of the equipment and the power in the beat unit can be obtained. Using 3-phase 3-wire products in one slot can measure up to 4 circuits, and using 3-phase 4-wire products can measure up to 3 circuits Therefore, through multi circuit products, electric energy measurement can be implemented in a small space. Mitsubishi / O module user manual. For example, one module can be used to measure other loads from the control panel trunk line. In addition, GX works2 (version 1.90u and higher) can be used to easily set parameters and bidirectional controllable brick output; 32 o'clock. Rated current and voltage: AC100 ~ 240V_ 0.6a/1 point, 2.4a/1 public end, 8:1 public end Mitsubishi / O module user manual. Response time: 1ms + 0.5 cycle. External wiring connection mode: 38 point terminal block (terminal block is sold separately). Replacement model: ay23, output: 2 channels, Input (resolution): 0 ~ 4000: - 4000 ~ 4000:0 ~ 12000-12000 ~ 12000: - 16000 ~ 16000 output: DC-10 ~ 10V: dc0 ~ 20maqh42p user manual. Conversion speed: 80us / 1 channel. 18 point terminal block. Transformer isolation between power supply and output. High insulation strength and withstand voltage. It can isolate electrical interference, such as current and noise. Standard analog input module. Isolated analog input module. No external isolation amplifier is required. When the inter channel isolated analog quantity module is not used. Qh42p user manual when using inter channel isolated analog module. Expand the possibility of control with intelligent functions. Provide various analog modules, which is an ideal choice for process control applications. It can also meet the needs of high-speed and high-precision control. It is most suitable for analog modules in the field of high-speed conversion control, Qh42p user manual for a variety of analog-to-digital and digital to analog conversion module products can be provided These modules have various functions and achieve maximum flexibility when connecting devices. It can meet the needs of high-speed conversion such as frequency converter control. Various modules with excellent performance Meet various control requirements from analog quantity to positioning. Q series module products include a wide variety of / 0, analog and positioning function modules. It can fully meet the input and output of switches and sensors, the control of temperature, weight, flow, motor and driver, and the positioning of high- precision control in the future! Control requirements in various fields It can also be combined with CPU module to realize appropriate control. Input voltage range: AC100-240V. Output voltage: DC5V Output power supply: 2A Ultra thin power supply. Simplify program debugging The software component test function with execution conditions can be used to change the software component value to the user specified value at any step of the program. In the past, when debugging a specific circuit program section, it was necessary to add a program for setting soft components At present, by using this function, specific loop program segments can perform actions independently without changing the program. Large, there is no need to change the program for debugging in the single, the debugging operation is simple, and the key data is automatically backed up Automatically save the program and parameter files into the program memory (flash ROM) without using the backup battery, so as to prevent the program and parameters from losing the qh42p manual due to forgetting to replace the battery. In addition, important data such as software component data can be backed up to standard ROM to avoid planned downtime during long holidays, These data are lost due to battery depletion. Mitsubishi / / O module user manual. The next time the power is turned on, the backed up data will be restored automatically. Through the extension of software components, it is more convenient to create programs. The software component can be extended to 60m bits at most

Minimum Order: 1 bags

A small remote I / O module used as a remote I / O station for control and communication links (hereinafter referred to as "CC link"). Its features are as follows: (1) The small remote I / O module reduces the volume while maintaining all the functions of the traditional module. (2) More models of small remote I / O module series Waterproof terminals are added to the small remote I / O module series for CC link system. Along with the traditional terminal block type, there are also quick connector type modules and FCN connectors Type and connector type, now there are five models of products. In addition to the traditional 16 point and 32 point remote I / O modules, an 8-point type is added, so that users can choose the most appropriate module according to their own purpose and environment. (3) The 4-wire small remote I / O module is easy to connect to the 4-wire sensor. It can be easily connected to the 4-wire sensor through the common pin provided on each plug. It is not necessary to install relay terminal block. For 4-wire small remote I / O modules, one sensor is connected to one plug. Therefore, the sensor can be changed through the plug, reducing the operation steps. (4) The terminal block connection makes it easy to connect 2-wire and 3-wire sensors or loads. Because the terminal block connection allows the connection of 2-wire and 3- wire sensors or loads, there is no need for a common connector, which makes the connection easier. (5) Minimize wiring (a) Terminal block module By using the self tightening screw on the terminal block, the wiring steps can be significantly reduced. (b) Quick connector module, connector module The wiring steps can be significantly reduced by using the parallel wire pressure wiring method (without welding, stripping the shielding layer and screwing). (c) FCN connector type module Wiring steps can be significantly reduced by using 40 pin connectors for I / O parts. (6) Waterproof remote I / O module has improved waterproof and oil proof effect The waterproof remote I / O module adopts a protective structure compatible with IP67, which can be used more safely in the presence of water and oil. (7) Up to 64 remote I / O modules can be connected In CC link system, each master station can connect up to 64 remote I / O modul Since each remote I / O module accounts for 32 points, a maximum of 2048 link points can be set. (8) The module can be replaced without stopping the CC link system The dual block terminal block used for CC link cable connection can be used to replace the module without stopping the operation of CC link system. (9) It can be installed directly on the machine The terminal block type remote I / O module can be installed directly on the machine because there is a live area protected by a finger guard in the area above the terminal block. (10) The module can be installed in 6 directions Small remote I / O modules can be installed in 6 different directions. (there are no restrictions on the installation direction.) The module can also be installed with DIN rail. (11) Transistor output module with improved protection function Transistor output module in order to achieve better module protection ability, as a standard model, its design adopts short-circuit protection, overload protection, overheating protection and overvoltage protection. Therefore, the reliability of PLC system has been further improved.

Minimum Order: 1 bags

Condition: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. Our Service: Terms: We ships worldwide and accepts T/T and Paypal. All items are subject to availability and passing our QA testing and inspection. Turnaround Time: Standard order processing is 1-2 business days plus shipping method chosen. Rush and off-hours service available for an additional fee. Packaging and Handling: Items are safely packaged in custom shipping cartons for protection. Shipping: We ship worldwide use UPS,FedEx, DHL or Truck Freight when meeded. Call to use a shipping service other than the ones listed. International Customers are responsible for all Customs fees, VAT and other fees applied by their respective countries. All shipments are fully insured

Minimum Order: 1 bags

Brand: Mitsubishi Product Name: servo driver model: mr-j4-70b1 axis servo amplifier. Mitsubishi universal AC servo amplifier melcervo-j4 series. Rated output: 0.75KW. Interface: sscnet Ш/ H。 Power supply: = phase ac200v The same server amplifier supporting sscnet Ⅲ / h. A fully synchronous system using high-speed serial optical communication can be established. It can be combined with the servo system controller to give full play to the functional performance of the servo system. By supporting the seismic algorithm of three inertial equipment, it can vibrate at two low frequencies at the same time. Mr configurator2 enables easy adjustment The low-frequency aftershock effect below 100Hz generated by the front end of the boom or the main body of the device can be effectively reduced, and the time required for aftershock control can be effectively shortened The accuracy of arc trajectory can be improved in the trajectory control of XY slide, At the same time, it can effectively control the quadrant protrusion caused by friction and distortion, Servo motor series: low inertia, medium and large capacity. Rated output: 15.0kw. Rated speed; 1500r / min. electromagnetic braking: without. Power supply: 200V. It is suitable for high-frequency operation or high acceleration and deceleration operation of medium, large capacity and low inertia products. Mitsubishi mr-j4-70b improves the environmental resistance. Hg-sr and hg-jr series products adopt IP67. High speed & high torque, shorten positioning time and realize high-speed equipment mr-j4-70b100 sites, there are 100 different drive controls. In order to meet diversified and detailed site needs as much as possible, In the configuration of mr-j4 product line, it provides rich servo amplifier and servo motor products. It can meet the different needs of different customers. Servo motor series: low inertia, small capacity. Rated output: 0.1kw Mitsubishi mr-j4-70b, rated speed: 3000r / min, electromagnetic braking: without. Power supply: 200V. The rated speed is 3000r / min and the large speed is 6000r / min. The high torque is 350% of the rated torque, realizing high knowledge transfer in the field of high rotation. It only supports hg-kr series products. Built in position encoder with high resolution Provide standard high-resolution position encoder (4194304p / rev (22bit)) to achieve more positioning function of Mitsubishi mr-j4-70b, Improve the environmental resistance. IP65 is adopted for hg-kr, hg-mr, hg-rr and hg-ur series products. Mitsubishi Electric general AC servo amplifier melcervo-j3 series. Rated output: 22.0kw. Interface type: CC link communication type (built-in positioning function) Mitsubishi servo driver. Power specification: three phase AC400V The positioning operation is realized by setting the position and speed data in the positioning table and receiving the start signal from the main controller. The setting of position, speed and other data in the positioning table and the start and stop operation can be completed through CC link communication. When the servo unit (dj-01-link) and (DJ-3) can not be used for positioning through communication, dj-01-link can be used for positioning. Using the servo amplifier with built-in positioning function, the position, speed and other data can be set through CC link communication. (corresponding to CC link version ver. 1.10) The Mitsubishi servo driver can be started, stopped and monitored through CC link communication. Serial communication reduces wiring The distributed servo control system can be constructed through CC link communication. The parameter unit mr-pru03 (option) makes parameter setting, operation and easier. The servo amplifier can be operated by dry speed control. When both stations are occupied, the speed command can be set directly through the remote passenger memory. Servo motor series: medium inertia, small capacity, rated output: 2.0kw. Rated speed: 1000r / min. electromagnetic braking: attached. Power supply: 200V. Realize the stable driving mr-j4-70b of medium capacity, medium inertia products, and realize the small total length in the industry through optimized structural design. High speed & high torque Mitsubishi mr-j4-70b can shorten positioning time, realize high-speed equipment and reduce power on torque ripple. By combining the number of poles and slots of Jiahua motor, the power on torque ripple is greatly reduced, and the smooth and constant speed operation of the equipment is further realized. To improve the environmental resistance, hg-sr and hg-jr series products adopt IP67

Minimum Order: 1 bags

The next generation servo product J4 is launched with safety specifications and eco correspondence. This product not only aims at the fastest speed in the industry, but also introduces the concept of the integration of human, machinery and environment into this product. ■ Mechanical aspect: the fastest speed frequency response performance of 2.5KHz in the industry is combined with the standard system equipped with 4194304 (22bit) decomposition for absolute position detector equipped with rotary servo motor. ■ Human aspect: towards human safety and comfortable environment, safety specifications correspond to the enrichment of easy to user design. ■ Environment: multi axis integrated servo driver with advanced function in eco era. ■ Inheritance: the combination of servo driver and controller of the previous model has a very corresponding design. Characteristic: Online products Generally, rotary servo, linear servo and direct drive servo correspond to the specifications of economic and environmental protection models with 2-axis integration and 3-axis integration. SSCNETⅢ/H Equippe , d with Mitsubishi's latest servo communication network, the data communication is the evolution of full duplex 150Mbps, the high response acceleration of the system, and the new generation products of optical fiber network are launched at the same time as J4. Advanced one touch functionality After pressing the setting torque once, the servo gain parameters such as mechanical common vibration filter and advanced vibration control filter II can be adjusted to help engineers easily achieve the optimal servo adjustment operation. Advanced vibration control filter II It has 3 low-frequency vibration control algorithms of inertial system, which can suppress two low-frequency vibrations at the same time. The vibration in the front end of the body and the corresponding device will be suppressed. Mr-j4 servo motor mr-j4-700b, a new product of Mitsubishi Electric in Japan Mr-j4 servo motor, a new product of Mitsubishi Electric in Japan 1、 Servo amplifier with conventional interface can correspond to 4mpps pulse frequency at most. 2、 Driver for motion control network sscnet Ⅲ / h. It is equipped with full closed-loop control as standard, which can drive rotary servo motor and linear servo motor. 3、 Driver for motion control network sscnet Ⅲ / h. It can drive two servo motors at the same time, saving installation space and wiring. It is equipped with full closed-loop control as standard, which can drive rotary servo motor and linear servo motor. 4、 Driver for motion control network sscnet Ⅲ / h. It can drive two servo motors at the same time, saving installation space and wiring. It is equipped with full closed-loop control as standard, which can drive rotary servo motor and linear servo motor. Mitsubishi mr-j4 series   MR-J4-A (general interface)    it has standard pulse sequence command interface and analog voltage input command interface    it can switch between various control modes such as position, speed and torque control   the standard supports command pulse frequency 4mpps   MR-J4-B(sscnet III / h interface)    the communication speed is 150Mbps and the communication cycle is 0.22ms    distance from wiring can be realized (maximum total extension distance 6400m: maximum 100m * 64 axis between stations)    because the optical fiber cable used is the same as the traditional sscnet III / h, it can be easily interchanged.   Mitsubishi servo amplifier mr-j4 series    mr-j4w3-b / mr-jw2-b (sscnet III / h interface, multi axis integrated servo amplifier)    it not only inherits the high performance, multi-function and convenience of mr-j4-b, but also drives two or three servo motors through one servo amplifier.    compared with mr-j4-b, mr-j4w2-b saves 25% - 30% installation space, and mr-j4w3-b saves about 30% installation space.   driver for motion control network sscnet Ⅲ / h. It can drive two servo motors at the same time, saving installation space and wiring. It is equipped with full closed-loop control as standard, which can drive rotary servo motor and linear servo motor.

Minimum Order: 1 bags

Fr-e740-1.5k-cht is an economical and high-performance type, 3-phase 400V power supply, and the motor capacity is * large and suitable for three standard 4- pole motors! Detailed parameters of fr-e740-1.5k-cht: 1. Power of fr-e740-1.5k-cht: 1.5kw 2. Current of fr-e740-1.5k-cht: 4A 3. Voltage of fr-e740-1.5k-cht: 3-phase 380 ~ 480v 4. Frequency of fr-e740-1.5k-cht: 50Hz / 60Hz 5. Allowable fluctuation range of voltage and frequency of fr-e740-1.5k-cht: 325 ~ 528v50hz / 60Hz (plus or minus 5%) 6. Power capacity of fr-e740-1.5k-cht: 4.5KVA 7. Overload capacity of fr-e740-1.5k-cht: 150% 60s, 200% 3S (inverse time characteristic) 8. Installation dimension of fr-e740-1.5k-cht: 140mm * 150mm * 135mm 9. Approximate weight of fr-e740-1.5k-cht: 1.9kg 10. Cooling mode of fr-e740-1.5k-cht: forced air cooling Selection method of fr-e740-1.5k-cht: 1. Fr-e740-1.5k-cht is selected according to the following load torque characteristics and is divided into the following three categories: (1) Constant torque load (2) Constant power load (3) Fluid load 2. Fr-e740-1.5k-cht is selected according to the control mode and is divided into the following five categories: (1) V / F open loop control (2) V / F closed loop control (3) Vector control without speed sensor (4) Vector control with speed sensor (5) Direct torque control Fr-e740-1.5k-cht selects the protective structure according to the use and installation environment: The protective structure of fr-e740-1.5k-cht should adapt to its installation environment, which requires consideration of environmental temperature, humidity, dust, pH, corrosive gas and other factors, which is of great significance to the long-term, stable, safe and reliable operation of fr-e740- 1.5k-cht. It is divided into the following four categories: (1) Open type (2) Closed type (3) Sealed type (4) Closed type 1. Select the frequency converter according to the load characteristics, If the load is constant torque load, Siemens MMV / MDV frequency converter shall be selected. If the load is fan and pump load, Siemens eco frequency converter shall be selected. 2. When selecting the frequency converter, the actual motor current value shall be used as the basis for the selection of the frequency converter, and the rated power of the motor can only be used as a reference. In addition, it should be fully considered that the output of the frequency converter contains high-order harmonics, which will deteriorate the power factor and efficiency of the motor. Therefore, the current of the motor increases by 10% and the temperature rise increases by about 20% compared with the power frequency power grid. Therefore, when selecting motor and frequency converter, this situation should be taken into account and appropriate allowance should be reserved to prevent excessive temperature rise from affecting the service life of motor. 3. If the frequency converter wants to run with a long cable, measures should be taken to restrain the influence of the long cable on the ground coupling capacitance to avoid insufficient output of the frequency converter. The frequency converter shall be selected by amplifying the first gear, or the output reactor shall be installed at the output end of the frequency converter. Shanghai Mitsubishi fr-e740-1.5k-cht 4. When the frequency converter is used to control several motors in parallel, the length of the motor cable and the allowable range of the frequency converter must be considered. If the specified value is exceeded, the frequency converter shall be selected by amplifying the first gear or the second gear. In addition, in this case, the control mode of the frequency converter can only be Vif control mode, and the frequency converter cannot protect the overcurrent and overload protection of the motor. At this time, it is necessary to add a fuse on each motor to realize the protection.

Minimum Order: 1 bags

Fr-d700 series Mitsubishi variable frequency governor compact multifunctional frequency converter 1. Power range: 0.47.5kw 2. General flux vector control, 150% torque output at 1Hz 3. Adopt long-life components 4. Built in Modbus RTU protocol 5. Built in brake transistor 6. Expand PID and triangular wave functions 7. Safety belt stop function FR-D720-0.4K, FR-D720-0.75K , , FR-D720-1.5K, FR-D720-2.2K, FR-D720-3.7K, FR-D720-5.5K, FR-D720 , -7.5K

Minimum Order: 1 bags

Function of braking resistance: 1 Protect the frequency converter; 2. Protect the power network. Braking resistance is a kind of ripple resistance, which is mainly used in the mechanical system of frequency converter controlling the rapid shutdown of motor. The firecracker motor converts the regenerative electric energy generated by the rapid shutdown into heat energy. The principle of resistance braking is that the rotor has current flow, which generates torque opposite to the rotation direction in the magnetic field of the stator, consumes the kinetic energy of the train, and achieves the purpose of braking. When the motor or other inductive load driven by the frequency converter stops, it is generally realized by energy consumption braking, that is, the kinetic energy of the motor and the magnetic energy in the coil are consumed through another energy consuming element after stopping, so as to realize rapid shutdown. Compent: Ceramic tube: it is the skeleton of alloy resistance wire and has the effect of radiator at the same time Alloy resistance wire: the flat belt has a wavy shape and is wound on the surface of the ceramic tube, which is responsible for converting the regenerated electric energy of the motor into heat energy The coating is flame-retardant on the surface of the alloy and has the characteristics of high temperature resistance Main hazards During the rapid shutdown of the motor, a large amount of regenerative electric energy will be generated due to inertia. If this part of regenerative electric energy is not consumed in time, it will directly act on the DC circuit part of the frequency converter. If it is light, the frequency converter will report fault, and if it is serious, the frequency converter will be damaged; The emergence of braking resistance solves this problem and protects the frequency converter from the harm of motor regenerative electric energy; Smooth operation The braking resistance directly converts the regenerative electric energy in the process of rapid braking of the motor into heat energy, so that the regenerative electric energy will not be fed back to the power network and will not cause grid voltage fluctuation, which plays a role in ensuring the smooth operation of the power network

Minimum Order: 1 bags

Condition: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. Terms: We ships worldwide and accepts T/T and Paypal. All items are subject to availability and passing our QA testing and inspection. Turnaround Time: Standard order processing is 1-2 business days plus shipping method chosen. Rush and off-hours service available for an additional fee. Packaging and Handling: Items are safely packaged in custom shipping cartons for protection. Shipping: We ship worldwide use UPS,FedEx, DHL or Truck Freight when meeded. Call to use a shipping service other than the ones listed. International Customers are responsible for all Customs fees, VAT and other fees applied by their respective countries. All shipments are fully insured.

Minimum Order: 1 bags

Common faults of ABB Robot Teaching Pendant: 1: ABB Robot S4 and irc5 teaching devices have poor touch or local failure (replace the touch panel) 2: ABB Robot S4 and irc5 teaching pendant have no display (repair or replace internal mainboard or LCD) 3: Poor display of ABB Robot S4 and irc5 teaching pendant, vertical line, vertical belt, flower screen, broken, etc. (replace LCD screen) 4: The keys of ABB Robot S4 and irc5 teaching pendant are poor or ineffective (replace the key panel) 5: Whether the teaching pendant of ABB Robot S4 and irc5 has display backlight (replace the high-voltage board) 6: The XYZ axis of the control lever of ABB Robot S4 and irc5 teaching pendant is poor or ineffective (replace the control lever) 7: The emergency stop button of ABB Robot S4 and irc5 teaching pendant is invalid or ineffective (replace the emergency stop button) 8: The data lines of ABB Robot S4 and irc5 teaching pendant cannot communicate or be powered on, and there are broken lines inside (replace the data line) ABB Robot parts and spare parts: ABB teaching box 3hne00313-1 m1998 M2000 teaching pendant ABB Robot Teaching box 3hac023195-001 ABB Robot irc5 teaching pendant dsqc679 3hac028357-001 ABB teaching pendant 3hab5386-1 ABB teaching pendant cable 3hac031683-001 ABB teaching pendant lever jc2000-0049 t (SPL) - xyz-popop-25-spl-spl-n ABB drive 3hab8101-13 / 07B ABB teaching box LCD 3hnp04014-1 I / O signal input and output board 3hac025784-001 dsqc651 I / O signal input / output board dsqc652 3hac025917-001 ABB Robot IO board 3hea800439-002 ABB interface board dsqc327a 3hac17971-1 ABB I / O mainboard dsqc 328a 3hac17970-1 ABB Robot I / O interface board dsqc327 3hab7230-1 ABB IRB 6400 main computer board dsqc 540 3hac14279-1 ABB industrial robot teaching board 3hne00313-1 main board 3hne30055 ABB Robot control board dsqc611 3hac13389-2 DSQC643 3HAC024488-001 ABB M2004 IRC5 ABB Robot base plate 3hac14363-1 / 00 dsqc541 ABB irb6400 computer board 3hac02347-001 / 01 dsqc532b I / O computer AB

Minimum Order: 1 bags