Minerals & Metals - Others

Gas Shielded Welding Wire Supplier Specification： ISO G46 4 M21 Z3Si AWS ER80S - G GB ER55 - G Shieding Gas 80%Ar + 20%CO2 Characteristics： (1)This product is the 600MPa grade high strength steel wire, it has very good mechanical properties.  (2)With the mixed shielding gas, this wire widely used in steel, mining machinery, engineering machinery, automobile and other industries. Precautions： 1. Pay attention to the gas purity and mixture ratio.  2. Keep the gas flow rate between 15 ~ 25 L / Min.  3. The extension length keep between 15 to 20mm   4. Clear the oil, rust, moisture, dust and other debris of the welded parts.  5. Keep the welding hood clean and unobstructed. Hebei XINYU Welding Co., Ltd, which mainly produces high strength steel welding wire, Non-copper-coated solid wire, submerged arc & stainless steel welding wire . Our products are widely applied to the welding of low-alloy high tensile large & key steel structures in coal machinery, construction machinery, petrochemical machinery, pressure vessels or tanks, oil & gas pipelines, military industry, shipbuilding, bridge and high-rise buildings etc. At the same time,we are the only interprise in the domestic which produces welding wire as well as welding wire equipment. Welcome you to our factory any time.

Minimum Order: 10 long tons

ER50-G Welding Wire Specification AWS ER70S-G J I S YGW15 G B ER50-G Shielding Gas 80%Ar+20%CO2 Feature & Use： ( 1 ) Operating condition is wide, from low to high current. It is a kind of solid wire. ( 2 ) Containing special alloy, its arc is stable even in high current. ( 3 ) Adapt to 490 MPa steel , like ships, steel structures, and machinery etc. Notice of ER50-G Welding Wire： 1. Please use specialized welding gas, eg: purity of CO2≥99.5%，H2O≤0.005%， Ar≥99.99%. Gas flow: 20~25L/min. 2. Wind affects arc and welding pool, please take steps to block the wind. 3. There is smoke when welding, pay attention to ventilation. 4. Distance between Tip and base steel is about 15mm when current is below 250A; and 20~25mm when current is above 250A. 5. Welding materials should be stored in dry places. 6. Please check the welder ,wire feeder, gas regulator and heater before operation. 7. Please keep the percentage of mixed gas stable and keep gas pressure stay the same. 8. As to thin steel plate, downward welding in the inclined position or forward welding is recommended,(pictures are followed below). 9. Please move plastic spool and basket spool in a correct way. One chemical composition of deposited metal (wt%)：（80%Ar+20%CO2） C Si Mn P S 0.08 0.42 1.04 0.016 0.025 Size & Current (DC+)： Diameter (mm) 0.8 0.9 1.0 1.2 1.4 1.6 Current  (Amp) PA 50 ~  180 50 ~  200 50 ~  220 80 ~  350 100 ~  470 200 ~  550 EGW 50 ~  120 50 ~  140 50 ~  140 50 ~  160 100 ~  180 — PE 50 ~  100 50 ~  120 50 ~  120 50 ~  140 — — We are Welding Wire Manufacturer and provide Quality High Strength Steel Welding, Non Copper Coated Wire, Submerged Arc & Stainless Steel Welding Wire.If you are interested, please click here to contact us immediately.

Minimum Order: 10 long tons

Gas Shielded Welding Wire Specification： ISO G42 4 M21 3Si1 AWS ER70S-6 GB ER50-6 Shieding Gas： CO2 or 80%Ar+20%CO2 XINYU Gas Welding Wire Description Characteristics： (1) This product is the general MAG / CO2 welding wire and suitable for all- position welding (2) The wire have stable arc at low currents , less sparks and splashing, and adapt to larger current range Precautions： 1. Pay attention to the gas purity and mixture ratio.  2. Keep the gas flow rate between 15 ~ 25 L / Min.  3. The extension length keep between 15 to 20mm   4. Clear the oil, rust, moisture, dust and other debris of the welded parts.  5. Keep the welding hood clean and unobstructed. One chemical composition of the weld metal sample  (wt%) （Shielding Gas:CO2） C Si Mn P S 0.08 0.68 1.32 0.011 0.008 Hebei XINYU Welding Co., Ltd, mainly produces high-strength steel welding wire, Non-copper-coated solid wire, submerged arc & stainless steel welding wire. Our Welding wires and welding wire equipment are exported to the USA, Italy, Brazil, Russia and India, etc. All products have passed ISO 9001-2015 quality system certification and CE certification.If you are interested, please click here to contact us immediately.

Minimum Order: 10 long tons

Specification AWS ER120S-G ISO G89 4 M21 ZMn3Ni2CrMo G B ER83-G Shielding Gas 80%Ar + 20%CO2 XINYU High strength steel welding wire Description Feature & Use： ( 1 ) For 890MPa high tensile steel, containing Ni，Cr，Mo etc，excellent mechanical properties. ( 2 ) Adapt to low-alloyed steel structures according to 890 MPa. Notice： 1. Please use specialized welding gas, eg: purity of CO2≥99.5%，H2O≤0.005%， Ar≥99.99%.

Minimum Order: 10 long tons

=Specification ISO G62 4 M21 ZMn3Cr AWS ER100S-G GB ER69-G Shieding Gas 80%Ar+ 20%CO2 Product Description Characteristics： (1) This product is the 700MPa grade high strength steel wire, it has very good mechanical properties.  (2) With the mixed shielding gas,XINYU Gas Shielded Welding Wire can be used to welding the important low alloy structures, and widely used in the welding of scraper chain and hydraulic supports in mining machinery Precautions： 1. Pay attention to the gas purity and mixture ratio.  2. Keep the gas flow rate between 15 ~ 25 L / Min.  3. The extension length keep between 15 to 20mm   4. Clear the oil, rust, moisture, dust and other debris of the welded parts.  5. Keep the welding hood clean and unobstructed. One chemical composition of the weld metal sample (wt%)  （Shielding Gas:80%Ar+20%CO2） C Si Mn P S Else 0.08 0.60 1.45 0.010 0.005 -- One mechanical properties of the weld metal sample  （Shielding Gas:80%Ar+20%CO2） Tensild Strength      MPa Yield Strength      MPa Elongation      % Impact Energy Value ℃ J 750 655 23 -20 94 The applicable current range and specifications of the product (DC+): Dia (mm) 0.8 0.9 1.0 1.2 1.4 1.6 Current Range    (Amp) Flat welding 50 ~ 180 50 ~ 200 50 ~ 220 80 ~ 350 100 ~ 470 200 ~ 500 Vertical up welding 50 ~ 100 50 ~ 140 50 ~ 140 50 ~ 140 100 ~ 180 — Overhead welding 50 ~ 100 50 ~ 120 50 ~ 120 50 ~ 160 — — Vertical down welding 50 ~ 100 50 ~ 200 — — — — We mainly produces Welding Wire, Stainless Steel Wire, Non Copper Coated Wire. Inculding er70s 6 welding wire, er80s g welding wire.Click here to browse the website.

Minimum Order: 10 long tons

• Manufactured from cross-linked polyolefin • Provide sealing protection and strain relief over multi-core cable crutch, including 2-, 3-, 4—, and 5-core breakout • Coated with adhesive on the body and the fingers to form a watertight seal • Flame-retardant breakouts are available upon customer request • Meeting with varieties of configuration requirements • Shrink temperature: start at 90°C, and fully recovered at 130°C.

Overview of the steel ladder stepping plate Stair Treads, also known as steel stair treads, are a kind of stair slab for platforms. Their installation methods include welding connection and bolt connection. The welded fixed treads can be directly welded to the ladder beam. Model of steel ladder step plate Model:T1,T2,T3,T4,T5,T6 Welding fixing: T1, T3, T5 Bolted fixing: T2, T4, T6 The width of treads is usually between 0.5m and 1m. Tread plate marking and tolerance ST4 - ST4 in (ra325 / 30) - tread plate model, ra325 / 30 steel grating model Step board tolerance: width W ± 3mm, length L-3mm. Recommended width of steel grating step plate(mm)

Cast Tungsten Carbide Powder For Hardfacing,Drill Bits And Diamond Tools​ (Fuse WC,Cast WC,CTC,Crushed WC) Chemical Compositions Grade W T.C F.C Fe Ti Ni Cr Co V BD20101 Balance 3.8-4.2 ≤0.05 ≤0.5 ＜0.1 3-5 ＜0.1 ＜0.1 ＜0.1 Hardness HRA Micro-hardness HV 0.1 Density g/cm3 Melt Point ℃ 93.0-93.7 1700-2500 16.5 2525 Regular Particle size Particle Size 20-30mesh 100-140mesh 30-40mesh 100-230mesh 40-60mesh 120-170mesh 60-80mesh 140-200mesh 80-120mesh 170-3250mesh 60-325mesh 200-325mesh 80-200mesh -325mesh Cast Tungsten Carbide: Chemical Formula:WC/W2C Cast Tungsten Carbide (CTC) is a so-called cast and crushed tungsten carbide. lt is of irregular particle shape. Adopted high temperature melting, crushing process. Due to its high melting point, high hardness, high wear resistance characteristics, make its have the characteristics of high temperature resistance, abrasion resistance, impact resistant. Products are widely used in mining, oil, metallurgical industry, steel, construction machinery and other industries. Such as: PDC bit, petroleum drill pipe, TC bearing, etc. Blends of CTC with alloy powders based on Ni, Fe or Co are used to produce superior wear protectioning coatings by PTA welding, lasercladding or other wear protective welding applications. Examples are conveyor screws, fan blades, wear plates. excavator bucket teeth and crusher iaws. Furthermore. CTC can be used for the production of drill bits.

We XinBo Precision has been engaged producing and supplying all kinds of CNC Milling parts over 10 years. Our flagship products include Brackets, Covers, Housings, etc. Conforming to all customer’s prints and the tolerance standard: ISO2768m, ISO2768f. These product supports a variety of applications, including chemical equipment, automotive industry, consumer electronics, etc. Except CNC machining, we also provide one stop solutions like heat treatment, finishing, assembly and inspection. Since we have CMM, so we can do the parts with GD&T requirements, we also accept the parts with special finishing requirements, for example musk partial surface and anodize at the rest surface, or extrude and saw to get the work blank, then machining.

Ferrosilicon is often used as a deoxidizer in steelmaking because silicon and oxygen are easily oxidized to form silicon dioxide. At the same time, because of the large amount of heat released during the formation of SiO2, it is also beneficial to increase the temperature of molten steel while deoxidizing. At the same time, ferrosilicon can also be used as an additive of alloy elements, and widely used in low alloy structural steel, spring steel, bearing steel, heat-resistant steel and electrical silicon steel, ferrosilicon in ferroalloy production and chemical industry, often used as reducing agent. Specifications Ferro Silicon Grade Chemical Composition(%) Si C Al P S ≥ ≤ Regulare Specs FeSi 60% 65 0.2 2.0 0.04 0.02 FeSi 72% 72 0.2 2.0 0.04 0.02 FeSi 75% 75 0.2 2.0 0.04 0.02 Low Al FeSi 75% 75 0.2 0.5 0.04 0.02

ASTM B196 Grade( C17200) Beryllium Copper Rod 25mmx1m With Bright Surface Product Normal Description: Product Name: Beryllium copper rod Grade: ASTM B 196 (C17200) Standard: ASTM B196,251,463; SAE J461,463; AMS 4533,4534,4535; AMS 4650,4651; RWMA Class 4 Product Size: 25mmx1m State: A(TB00),1/2H (TD02), H(TD04),AT(TF00),HT(TH04) Typical Application: used for low maintenance bearings and bushings Product Brand: CUBERYLLIUM® International Specification of C17200 Beryllium Copper Rods: Rods/Bars/Tubes: ASTM B196,251,463; SAE J461,463; AMS 4533,4534,4535; AMS 4650,4651; RWMA Class 4 European Standards: CuBe2, Alloy 25, QBe2, BrB2, DIN.2.1247, CW101C to EN Note: ASTM: American Society for Testing and Materials SAE: Society of Automotive Engineers AMS: Aerospace Materials Specification(Published by SEA) RWMA: Resistance Welder Manufacturers' Association Note: Unless otherwise specified, material will be produced by ASTM.

Perimeter Safety Screens climbing net steel safety mesh scaffolding system safety mesh The perimeter safety screens is also called protective perforated mesh, mainly used in various construction sites, especially high-rise buildings, and can be fully enclosed for construction. It can effectively prevent personal and object falling injury, prevent fire caused by welding sparks, reduce noise and dust pollution, achieve the effect of civilized construction, protect the environment and beautify the city. Product Name Outer frame protective screen building peripheral net building safety protective screen Product Specification 1.2X1.8M Frame:20mmX20mmX0.5mm Product material Galvanized plate 0.4mm-0.8mm Product color Green Blue also can be customized Product advantage 1. No need to turn over the shelf 2. Assemble at one time until the construction is completed, saving manpower and materials

FRP corss arm of 10KV to 275KV has advantages of aging-resistance, light weight, electricity insulation and cheap cost Specification: Product Dimension (mm) Weight (kg/m) SQUARE TUBE 25x3.2 0.69 32x3.2 0.64 38x4.0 0.98 50x4.0 1.36 50x5.0 1.67 50x6.3 2.06 63x6.3 2.60 76x3.2 1.75 76x4.0 2.13 76x5.5 2.87 76x6.3 3.15 Introduction: FRP profiles are high strength composite that comprises the reinforced material, thermosetting resin matrix (polyester, VE,, phenolic, epoxy, etc) and glass fiber (in the form of roving, mat, fabric etc.) supplementary curing agent and addictives, and cures to the desired shape through a certain process.

High efficiency grinding service with pcd grinding machine Not only can we male PCD Grinding Machine, we can also offer pre-machining service to grinde the materials smoothly and efficiency. Material PCBN tips on tungsten carbide insert Grinding Amount 0.15mm Passivation value 0.005 Negative chamfer -15°*0.075 Grinding Accuracy +/-0.005mm Grinding Efficiency 1000pcs/day/set About Processing Procedure: 1. Stable and reliable grinding machine 2. Professional and skilled techinician team 3. Precision cutters’ sharpening 4. High efficiency 5. Improved surface performance and appearance