Mechanical Hardware

Dante is from a hydraulic manufacturing company in Greece. In the first half of last year, they wanted to upgrade the lifting stability of the company's original elevator. The function of the hydraulic cartridge counterbalance valve is the key. Dante made samples from a local hydraulic cartridge valve manufacturer that has been cooperating for 5 years. The stability has not reached the assumption of upgrading. After 2 times of improvements, the effect is still not obvious. Dante contacted more than 10 hydraulic cartridge valve manufacturers, but failed after a week. The boss urged the progress many times, and Dante was worried. Dante found AAK on Google, noticed that AAK had some customer cases about hydraulic cartridge counterbalance valves, and sent an email asking: Can AAK hydraulic cartridge counterbalance valve achieve fast start and stable positioning? After communication, we learned that they wanted to upgrade the equipment, and the key selling points of the equipment is to be started quickly and positioned steadily. According to the hydraulic system schematic diagram and the original hydraulic cartridge counterbalance valve drawing provided by Dante, after discussion, AAK engineers confirmed that the original hydraulic cartridge counterbalance valve can be optimized to achieve fast start and stable positioning. After 45 days, AAK sent 10 samples of hydraulic cartridge counterbalance valves.   2 months later, Dante sent an email saying that their engineers were satisfied with the function of AAK hydraulic cartridge counterbalance valve, which realized their lift selling points. Their sales team was confident to do a good job in market promotion and achieve the hot sale of equipment. AAK hydraulic cartridge counterbalance valve can solve the contradiction between response speed and stability, and has no back pressure effect. On the basis of the original, it has made 3 unique optimizations:   1. A fixed damping is installed between the inlet of the hydraulic cartridge counterbalance valve and the pilot oil port. The oil inlet of the valve body is 2 connecting ports of the oil circuit, and is equipped with a pressure gauge interface.   2. The valve spool of the hydraulic cartridge counterbalance valve slides in the upper and middle part of the valve body. The middle section of the valve spool has an inner concave ring, which is the inlet of the hydraulic cartridge counterbalance valve. The right end of the inner concave ring of the valve spool is processed into a conical surface. The conical surface is equipped with a two-stage stepped taper ring. The cumulative area of the conical surface is the same as the area of the cylinder end face at the right end of the valve spool. The stepped taper is adopted to realize the smooth flow change and smooth movement of the hydraulic cartridge counterbalance valve.   3. The cylindrical outer circle at the right end of the valve spool of the hydraulic cartridge counterbalance valve slides with the middle hole of the valve body. The adjusting screw is installed at the top pressure of the rear end of the balance adjusting spring. The adjusting screw is matched with the rear end of the valve body and controls the telescopic operation of the balance adjusting spring.   The optimized hydraulic cartridge counterbalance valve adopts the hydraulic control automatic closing valve to realize the unity of quickness and stability of the hydraulic cartridge counterbalance valve. At the same time, the pressure compensation is used to make the safety overflow function of the hydraulic cartridge counterbalance valve not affected by the back pressure. It can be applied to the hydraulic system with closed center and open center.   AAK hydraulic cartridge counterbalance valve, fast start, stable positioning, you can also try it! https://www.aakindustry.com/info-detail , /cartridge-counterbalance-valves-aak474

A few days ago, I saw a video of Faye Wong's speech. She is a well-known singer in China. When she received an award, she spoke in this way, which roughly means: I know I sing very well myself, thank you for the recognition of my singing skills by the organizing committee, and I also acknowledge their appreciation level. Upon hearing this, I feel the same way. When hydraulic cartridge valve manufacturer AAK receives the first inquiry from a new customer, I always inform them that AAK has supplied 3 Fortune 500 companies. Thank you for your inquiry for hydraulic cartridge valve manufacturer AAK. I admire your vision in choosing AAK and believe that you are different from other customers, especially in terms of manufacturing quality. Why does Faye Wong sing well? Because she no longer needs to prove herself, let alone care about others will say good or bad about what she sings, and she only focuses on understanding the song and immersing herself in emotions. Singing is a pleasure for her. Such a confident person's voice is destined to be like a heavenly sound. If a person is not sure about her profession, I believe her profession must be flawed! If a manufacturer of hydraulic cartridge valves is unsure of his manufacturing quality, I believe that the manufacturing quality of the manufacturer is unstable. The charm of confidence is unstoppable. A confident hydraulic cartridge valve manufacturer brings customers a sense of security and trust. Perhaps there is someone else who dislikes Faye Wong's "unwavering" attitude and criticizes her, but never conceals the brilliance of such "superstars", making "white jade with slight flaws" more authentic. This world will instinctively accept the temper of the strong and call it personality. If there is no top-notch professional competence and confidence, it can only be criticized as arrogance. To put it plainly: Insolence requires capital! The insolence of a hydraulic cartridge valve manufacturer lies in its stable manufacturing quality; It's because other hydraulic cartridge valve manufacturers cannot do it, and he mass-produced it a few years ago; It's because other hydraulic cartridge valve manufacturers are competing for prices, while he is competing for technological upgrades. I really don't like people who like to label people. Just judging a person by their words is humble or insolent, and completely ignoring his strength. Note: Some people are humble because they have self-awareness. And some people are insolent; he's just telling the truth. Hydraulic cartridge valve manufacturer AAK in China is a bit insolent in terms of manufacturing quality, and maintains humility in dealing with people. AAK HYDRAULIC CARTRIDGE VALVES (648) 2023-08-13 https://www.aakindustry.com/info , -detail/hydraulic-cartridge-valve- manufacturer , s-aak648

Someone asked me, you are not a mechanical professional. How can you guide AAK engineers to solve some difficult and complicated problems of hydraulic valves? Now the hydraulic valve industry has entered the stage of vertical specialization. Unprofessional may be a problem. Although specialization is the standard way to professional knowledge, it may not be a good thing from the perspective of creativity. Because sometimes professional knowledge is a double-edged sword. If you are too professional in hydraulic valves and have too much professional knowledge of hydraulic valves, you may not notice those distant associations. I have always insisted that the solution to the problem is to cast a big net first. Sitting next to the computer at 4:30 in the morning, I have 3 hours of association and quiet time. This is the darkness that does not belong to anyone. People usually wake up at 7:30, I have enough calm and patience to associate with the hydraulic valves and daydream at will. To do something creative, many people say that we should jump out of the box and think, but I think we should do the opposite and learn to think in the box. I often advise my engineers not to create the function of hydraulic valves by imagination, but to innovate on a certain basis of hydraulic valves. Ten years ago, we bought some representative hydraulic valve standard parts and some novel non-standard hydraulic valves from the top 10 hydraulic valve manufacturers in the world from the United States and Europe, comprehensively dissected these big brand hydraulic valves, refined the selling points of technical parameters, and then innovated on these basis. Only then did we have 3 domestic patents and processes and 4 proprietary technologies of AAK hydraulic valves, and AAK hydraulic valves were exported to more than 20 countries, 6 international first-line brand customers have placed orders for 5 consecutive years, and re-buy rate of AAK hydraulic valves from old customers is no less than 62% every year. What you think is right and what you can accept is basically wrong. What you think is wrong and what you can't accept are basically right. I read about 30 pages of books that are not related to the hydraulic valves every day. In the process of reading, I set aside a little time for daydreaming. For example, an idea in the book aroused my curiosity. I need to pause to connect my brain with this curiosity. Sometimes my brain will unconsciously link to the hydraulic valves. Every coin has two sides, depending on the angle we look at. For a half a glass of water, what some people see is: Alas, there's only half a glass of water left; What some people see is: Wow, still have half a glass of water. Pessimists are often right. I admire the pessimists' comments on the real world. Really, they are right, but most of them are losers. Simple minded optimists may not succeed, but they often live a good life. When I encountered the problem of hydraulic valves and couldn't find the answer after thinking hard, I found that sitting at my desk was almost a waste of time. Write out the hydraulic valve problem and knock it in the computer document, preferably on paper. Many people don't write it out, but trap the problem in their brain, which may not awaken their subconscious mind. Then, I will stay away from this hydraulic valve problem. Sometimes, when taking a bath or walking, the rudiment of the answer may come to mind. It's so wonderful. Turn off the music, stay away from the mobile phone, stay away from distractions, and let the brain unconsciously look for associations between different ideas. There may be surprises. Insist on getting up early, reading and exercising, because if you can't persevere, you won't get anything. Those who have not been engaged in the production of hydraulic valves for more than 10 years can hardly have a comprehensive understanding of hydraulic valves. Both enterprises and individuals should stick to their commitments to others, especially to themselves. I have no confidence in anything readily available, improvised and fast, but I believe in the power of stability, peace and long-term flow. Still water runs long. Any hydraulic valve manufacturer should be practical. I never believe that hydraulic valve manufacturers who lack self-discipline and self-growth will have a beautiful future. For example, in life, talented people are easy to bring traffic, but can't bring trust. The builder of self-discipline may not surprise people in a short time, but will gain long-term respect. This may be the cornerstone of trust. AAK hydraulic valves, no trickery, only daily self-discipline construction. https://www.aakindustry.com/i , nfo-detail/hydraulic-valves-aak234

After we posted the last article,“For hydraulic cartridge valves with high requirements, AAK produces them using 5-axis CNC machine tools, someone left a message: Can AAK use a 5-axis machining center to process hydraulic manifold blocks? From the IP, it should be a customer from Russia. Most hydraulic manifold manufacturers do not use this sophisticated equipment to produce hydraulic manifold blocks. How does hydraulic manifold manufacturer AAK use a 5-axis machining center to process hydraulic manifold blocks? Most hydraulic manifold manufacturers use domestically produced or Taiwanese machining centers for their hydraulic manifold blocks, because the accuracy requirements for most hydraulic manifold blocks are not high, and 5-axis machining centers are also expensive. Not every hydraulic manifold manufacturer can have a 5-axis machining center. Why this Russian customer requires a hydraulic manifold manufacturer to use a 5-axis machining center to process hydraulic manifolds blocks? He is likely to have encountered trouble with the valve hole accuracy of the hydraulic manifold blocks not meeting the standard. The higher accuracy the hydraulic manifold blocks require, the more they need to be machined on a 5-axis machining center. Today, the hydraulic manifold manufacturer AAK workshop was processing hydraulic manifold blocks on site, and I took a video for the processing. From the video, it can be seen that this is a horizontal 5-axis machining center from Japan. The advantage of this equipment is that the hydraulic manifold block can be processed with just one clamping of the blank parts. Most hydraulic manifold manufacturers process one surface before processing another, which not only has low efficiency but also poses risks of inaccurate positioning. AAK technicians first place the rough piece of the hydraulic manifold block on the fixture, position it while calibrating it with a balance ruler, then tighten the fixture and calibrate it again with a balance ruler until the positioning is correct, and then start the equipment. The dual box structure of this equipment ensures stable machining accuracy. Especially when the rectangular guide rail is combined with the movable mechanical structure of the column, the cutting becomes smoother and the accuracy of the valve hole is also stable. AAK hydraulic manifold blocks, processed with a 5-axis machining center, welcome to try it out! AAK HYDRAULIC CARTRIDGE VALVES (761) 2024-01-18 https://www.aakindustry.com/info , -detail/hydraulic-manifold-manufacturers- aak76 , 1

PRODUCT DESCRIPTION PN30 1/4 inch Forged Brass Ball Valve with L Type Handle Description ​Working Pressure 30 bar (435 psi) Working Temperature –20°C ~150°C (-4°F~302°F) In Absence Of Steam Thread ISO228 (equivalent to DIN 259 and BS2779) Opening/closing Test 10,000 times ​​ Details ​Brass Body: High-density forging, no blister, no air holes, no leakages,corrosion preventive. Made by high precision automatic CNC machines. Brass Bonnet: High-density forging, no blister, no air holes, no leakages,corrosion preventive. Made by high precision automatic CNC machines. Valve Ball: Smooth and good wear resistance, with good sealing performance. Brass Valve Stem: Made of hot rolled brass, high strength, good toughness, long-term use without deformation and fracture. Ball Seat: Made by pure PTFE(polytetrafluoroethylene), with high elasticity and wear resistance. Handle: Aluminium alloy T handle, professional surface painting, wear resisting, anti-corrosion. Small appearance, flexible in open and close. O-ring: NBR & FKM, made of imported raw material, small friction coefficient, long service life and not easy to leak. Stainless Steel Locknut: Internal design of anti-loose, can be used for long time. customization The entire product can be customized just to meet your needs. Company Profiles Taizhou Yuehao Technology Co., Ltd. is located in Qinggang Industrial City, Yuhuan City, Zhejiang Province, in the centralpart of China's Golden Coast and the southern wing of the Yangtze River Delta Economic Circle. The company currentlycovers an area of 10000 square meters and has over 100 outstanding employees. It is a professional valve manufacturer that integrates research and development, production, and sales. FAQ Q: How long is your product guarantee period? A: We have five-year guarantee and comprehensive after-sales process. Q: What is your MOQ? A: We have no MOQ. We have a large warehouse so that we can deliver goods immeditly. Q: Can you accept OEM? A: Both of OEM and ODM are acceptable for us. Q: How long is your delivery time? A: For the items if we have enough stocks, we can send to you immediately. For mass production, we can promise 30-45 days because we have a considerable number of automated equipment for 24-hour production.

An American IP left a message on our website: I saw your article "I regard quality as the highest principle of hydraulic valve manufacturing, why?". I want to know how AAK defines the quality of hydraulic valves. I specially checked the IP, which is an engineer from an engineering company listed in the United States. I thought for half an hour. To define a category, it must be comprehensive. What are the total quality of hydraulic valves? How much do we understand the quality of hydraulic valves? First, don't check the encyclopedia, Google, or hydraulic valve academic, but focus on hydraulic valve common sense. In common sense, how do you understand the quality of hydraulic valves, because our users also understand the quality with common sense. Friends who have read science and engineering know that there is a very famous management in Japan called total quality management. Of course, PDCA was invented by American Deming. What is carried forward is in Japan. The well- known Japanese enterprises implement total quality management. Almost all those engaged in manufacturing industry know total quality management, but few mention total quality. Some people say that total quality management has talked about total quality? Wrong, total quality management does not talk about total quality, only about management. For the total quality of AAK hydraulic valves, I have defined 4 kinds of quality. The 1st is the manufacturing quality of hydraulic valves, the 2nd is the service quality of AAK, the 3rd is the functional quality of hydraulic valves, and the 4th is the performance quality of hydraulic valves. The manufacturing quality of AAK hydraulic valves is now benchmarked with the international first-line brand, and the future is to surpass the international first-line brand. Especially in a subdivision field, such as high-pressure hydraulic valves, we should achieve top 1%. 1. AAK has been hydraulic valve ODM manufacturer for 3 of the world's top 500 for 10 years. The quality control process is strict and self-implementation is more strict than ISO certification system. 2. AAK has high-precision machine tools imported from Switzerland, Mikron GF high-precision CNC machining center and GILDEMEISTER turn milling compound machining center. 3. AAK has a full-time material engineer to check the selection of materials, which is responsible for screening, comparison, testing new materials connected with the Research Institute. AAK technical team has engineers from the world's top 500 hydraulic valve enterprises. They have their own experience in production drawing design, programming and production line quality control. Service quality of AAK: 1. AAK provides 24-hour responses, 48-hour solution plans and 72-hour problem solved before, during and after sales. Our peers dare to think but dare not to do it. 2. Six international first-line brand enterprises imported from AAK, because of feel at ease, all the hydraulic valves with low MOQ, high precision and urgent delivery, were purchased from AAK, due to AAK’s mindfulness. 3. 3-year warranty. Most of our peers dare not think about it, let alone do it. AAK hydraulic valve function quality and AAK hydraulic valve performance quality. First, let's find out what the function is and what the performance is? For example, 8 years ago, our mobile phones could not take pictures, but now smart phones can take pictures. Taking pictures on mobile phones is a function; The quality of pictures is a kind of performance. AAK hydraulic valve is differentiated and different by function and performance, especially in the field of high-pressure and high-precision subdivision, absolutely different. AAK hydraulic valve function quality: 1.The complete function of hydraulic valves is the least worth mentioning guarantee of AAK. 2.Each batch of materials shall be subject to heat treatment and never cut corners. Each hydraulic valve shall pass through the hydraulic table, with test reports and video records. Each hydraulic valve shall be tested 3 times and the test results shall be archived. 3.3 design patents, 4 proprietary production and processing technology, and the technicians in the core posts have been experienced for more than 8 years. Their proficiency is like a ruler. The old mechanic who has been in the factory for more than 10 years can sometimes judge the production status by just listening to the sound of the machine, and each production link of the hydraulic valves is engraved in his mind. Performance quality of AAK hydraulic valve: 1.The hydraulic valve with 3-year warranty has no vibration, no noise and high pressure resistance. 2.The machining surface accuracy of hydraulic valves is improved to within 0.3μm, the internal leakage can be less than 2drops / min. 3.Hydraulic valves with pressure resistance above 450bar and service life exceeding 2 million times, AAK hydraulic valve, Any valve, Any one, Any time, Any Where, just safety. Maybe I read too few books. I can tell you that almost no master, marketing master or management master has said the subject of total quality. At least, the concept of "total quality" has not been put forward in the hydraulic valve industry. I said a little more narrowly. For the definition of hydraulic valve quality, AAK is the first person to define the hydraulic valve quality with 4 aspects of total quality. AAK hydraulic valves, Any valve, Any One, Any time, Any Where, just Safety! https://www.aakindustry.com/info-de , tail/hydraulic-valves-aak233

Aether is a customer of AAK in Greece and has been purchasing hydraulic cartridge valves from AAK for 3 years. At the beginning of last year, he asked me about the sealing ring options available at AAK and I felt a bit strange. I didn't provide a direct answer and take an example, if I simply asked the doctor about the medication options, the doctor would definitely need to know the patient's symptoms or cause. After further communication, it was learned that they had encountered difficulties on a hydraulic directional control valve. Due to rapid wear of the sealing ring of the hydraulic directional control valve, there was leakage and the equipment was abnormal. The original manufacturer blamed the hydraulic directional control valve for being used too frequently, resulting in wear and tear on the sealing ring, which can only be replaced with new ones. Aether cannot accept replacing the sealing ring within only 3 months. Aether's demand is to address the issue of hydraulic directional control valve leakage without the need for frequent replacement of sealing rings. When I received the sample of the hydraulic directional control valve from the original manufacturer, I found that Aether had sent me an inquiry for this model before. I also understood why he only asked about the sealing ring at first. I told Aether that the original sealing method is a metal conical hard seal, which is difficult to ensure leakage if used frequently. Optimizing the original sealing structure can achieve no leakage for more than 1 year, but the production cost of hydraulic directional control valves would be increased. Aether was also candid and told me frankly that when inquiring, it was because AAK's price was more than 20% higher another hydraulic cartridge valve manufacturer that he chose. 60 days later, AAK sent out 50 samples of hydraulic directional control valves to address Aether's urgent needs first. Last week, Aether informed us that AAK hydraulic directional control valve has been installed on the equipment for almost a year and there are no leaks. Their customer is very satisfied, and his boss also suggested that he make AAK their preferred supplier of hydraulic directional control valves. The production cost of AAK hydraulic directional control valve is high, which is because these 3 aspects require more money than peers. AAK hydraulic directional control valve adopts a dovetail groove sealing ring through the valve spool pressure plate, which is pressed against the step hole of the valve body along with the valve spool, playing a sealing role. Oil cannot return from the inlet chamber to the return chamber, achieving zero leakage. 1. The hydraulic directional control valve body is connected to the spring seat, and the spring is fixed between the valve spool and the spring seat. There is a clearance fit between the valve spool and the valve body, as well as between the spring seat and the valve spool, to prevent the valve spool from moving inside the valve body. The guiding effect is formed between the spring seat and the valve spool, and the pre tightening force of the spring is changed by rotating the spring seat, thereby changing the opening pressure of the valve. 2. There are step holes on the valve body that guide the valve spool. There is a dovetail groove on the valve spool, which is equipped with a sealing ring to isolate the oil inlet and return chambers. Adopting a dovetail groove sealing structure and fixed by the valve spool pressure plate, it replaces the original metal conical hard seal. 3. The control rod is installed in the control chamber of the valve body, which has several oil passage grooves that return to the oil chamber and are fixed by elastic retaining rings. AAK hydraulic directional control valve, zero leakage, you can also give it a try! AAK HYDRAULIC CARTRIDGE VALVES (554) 2023-04-07 https://www.aakindustry.com/info , -detail/directional-control-valves-aak554

Marten is an old customer from a Dutch hydraulic company. He is very cautious in the business of hydraulic valves and never changes hydraulic valve suppliers easily. AAK hydraulic valve reached the first cooperation of hydraulic relief valves under the introduction of his friend.  It has been 3 years, and he orders 2 types of hydraulic relief valves with AAK every year. We have a very good personal relationship, and often communicate about some hydraulic valve technology.   Last month, Marten had an order for a special hydraulic relief valve that requires a surface roughness Ra of 0.1~0.2μm, which is more than 4 times accurate than the normal standard.  All the hydraulic relief valves of this series are purchased from the hydraulic valve manufacturer that he has cooperated with for 5 years. This manufacturer has tried this hydraulic relief valve for 3 consecutive times, but the Ra value is still not up to standard.  Marten thinks of AAK hydraulic valve. In the email, he has been emphasized that the surface roughness Ra value of hydraulic relief valve must reach 0.1~0.2μm.  According to the hydraulic relief valve drawings sent by Marten, after discussion, AAK engineers expressed 90% certainty that the Ra value could reach 0.1~0.2μm.  Marten seems to see hope, but also fear.  He asked AAK TO try samples immediately. At the same time, the original hydraulic relief valve manufacturer was also requested to continue the sampling.   AAK arranged the most experienced technicians to operate the knife, first of all in the rough turning stage, cutting depth adjustment to 0.8~1.5mm, feed to 0.2~0.3mm/r, cutting speed to 30~50m/min and so on, after the rough turning Ra value is 12.5~6.3μm, while leaving 0.5~1mm as fine turning margin;  Secondly, in the finishing stage, the cutting depth is adjusted to 0.1-0.3mm and the small feed is 0.05-0.2mm /r. At the same time, the cutting speed is ensured to reach the moderate value and the roughness Ra value is ensured to reach 0.2-0.16μm.  AAK sent the hydraulic relief valve samples 10 days later.   On the 3rd day after receiving the samples of AAK hydraulic relief valve, Marten informed us by email that the Ra value of the surface roughness was up to standard. At the same time, he also informed that the original hydraulic relief valve manufacturer also continued the sampling, but failed in 5 samples for 5 times, while AAK succeeded in one time. He asked us to catch time to prepare material, he would discuss the PO of hydraulic relief valve with AAK after he confirmed the order quantity and the delivery date with his customer. For high precision hydraulic relief valve roughness Ra value, in addition to use high precision lathes, good technicians are the key, to be good at adjusting lathe parameters according to different processing, for this hydraulic relief valve, AAK technician advantages are reflected in:   1. High speed and small cutting depth and feed are selected to reduce the residual area and Ra value. When finishing, select high-speed and small cutting depth and feed rate to reduce the residual area and reduce the Ra value. 2. Grinding the front and rear tool surfaces of the turning tool with engine oil, can effectively reduce the Ra value of the workpiece surface. 3. The 32 year old mechanic operating the machine tool, who can know whether the Ra value of the hydraulic relief valve is normal or not by just listening to the processing sound. The Ra value of AAK hydraulic relief valve is 4 times that of the conventional standard and 2 times that of its peers. You can also have a small try. https://www.aakindustry.com/info-detail/hy , draulic-relief-valves-aak232

Mason is from a hydraulic equipment company in India. It has been 3 years since he purchased hydraulic cartridge valves from local hydraulic cartridge valve manufacturers in India. At the beginning of this year, their company developed a hydraulic crane and needed hydraulic cartridge counterbalance valves. They chose a local hydraulic counterbalance valve manufacturer who has cooperated for 5 years to make samples. During the equipment debugging, it was found that the crane vibrated during the descending process and the descending speed was abnormal. The after-sales servicer believed that the hydraulic cartridge counterbalance valve was abnormal. After the original manufacturer inspected the hydraulic counterbalance valves, all parameters were in accordance with the drawing parameter requirements. After internal discussion, it was concluded that the hydraulic counterbalance valve must be optimized, but the original manufacturer had no ability to do it. The boss asked Mason to look for overseas suppliers of hydraulic cartridge counterbalance valves. A week has passed, the manufacturer of the hydraulic counterbalance valve has not been determined yet. The boss was not satisfied. Mason began to worry. Mason found AAK on Google, stayed on AAK website for 23 minutes, and left a message: Can AAK design a hydraulic cartridge counterbalance valve to solve the instability and abnormal speed of the hydraulic crane during the descending process? For those who stay on AAK website for a long time, no matter which country they come from, as long as they are not hydraulic cartridge valve manufacturers, I will do my best to help. After communication, I learned that Mason was embarrassed to purchase hydraulic cartridge counterbalance valves. According to his system schematic diagram, hydraulic cartridge counterbalance valve drawing and crane working video, AAK engineer had a basic idea. 3 days later, AAK began to sample. After 40 days, AAK sent 6 hydraulic cartridge counterbalance valve samples. A month later, Mason emailed that after the new hydraulic cartridge counterbalance valve designed by AAK was used, the hydraulic crane did not shake during the load lowering process, and the speed was even. Their colleagues were very confident in the promotion of the cranes, and the boss was also happy. AAK does not use the traditional route to optimize the hydraulic cartridge counterbalance valve. According to the system diagram of the equipment and the abnormality of the crane, the hydraulic cartridge counterbalance valve is composed of valve body, valve seat, main valve spool, pilot valve spool and pilot mechanism. First, connect the valve seat with the valve body to establish a connected first channel. The extended end of the valve seat is connected with the pilot mechanism to establish a second channel. The main valve spool adopts sliding setting, and is equipped with throttling groove and orifice. Then the valve seat cavity is divided into 3 cavities, one end of the valve spool is in the inner cavity, and the other end is connected with the pilot mechanism. The valve spool is flexible, controllable and free from load interference. Last week, Mason told me privately that his boss decided to increase the purchase of hydraulic cartridge valves from China and give him more authority. He was more confident in his work AAK hydraulic cartridge counterbalance valve, is not only a surprise, you can also have a small try! https://www.aakindustry.com/info-detai , l/hydraulic-cartridge-counterbalance- valves-aa , k405

In the early stages of its entrepreneurship, AAK, like other hydraulic cartridge valve manufacturers in China, supplied to the domestic market. After a few years of turmoil, funds have become tight, and there are more and more customers on credit. The price competition has also become increasingly fierce. Most hydraulic cartridge valve manufacturers only focus on prices, do not make technological breakthroughs, and do not invest in innovation. I know that hydraulic cartridge valve manufacturer AAK must make changes and focus on the overseas market. My confidence stems from the stable manufacturing quality of AAK hydraulic cartridge valves, which are supplied to domestic listed companies, There is also the fact that it has never been returned. A few years ago, I didn't even know about 'brain science', I just knew I needed to write tweets, post B2B, shoot videos, and update on the website. Enquiries come one after another, including Fortune 500 companies, listed companies, and high-quality customers. Some hydraulic cartridge valve manufacturers also imitate AAK's approach by writing a few diaries, filming several videos, and doing several live broadcasts... but they can't bear it anymore, giving up is inevitable. Hydraulic cartridge valve manufacturer AAK has always insisted on writing, filming, and broadcasting. People may be curious in their hearts, where does that power come from? The answer lies entirely in brain science. In fact, many manufacturers who are persevering have not studied brain science, but their writing, filming, and broadcasting are in line with brain science, and those target customers are also people, and they must follow the principles and laws of brain science in cognition and thinking. In this way, those manufacturers who insist on writing, filming, and broadcasting will definitely have more inquiries and orders. Can we do business without understanding brain science? Of course we can. But when you understand brain science, your feelings, motivation, and mindset are completely different from before. This is how hydraulic cartridge valve manufacturer AAK gradually came to understand. The 4 books "The Consciousness Instinct", " Mind", " What Your Customer Wants and Can't Tell You", and " The Persuasion code" are all good for flipping through when you have nothing to do. If you have a lot of work to do every day, it's better to let it go for now. When you have free time, take it out and read it, perhaps it can help you understand many whys. Is the mind a product of the brain, or is it independent of the brain? Studying brain science, just like hydraulic cartridge valve manufacturers doing foreign trade, is difficult at the beginning. Just understanding a bunch of professional vocabulary first can make people retreat from difficulties. But when everyone has retreated, the hydraulic cartridge valve manufacturer AAK does not retreat. Keep going, haha, the taste is coming, and it's very good. These are new books from recent years, exploring the entry of brain science into the post brain science era, including the application of behavioral economics in marketing and sales. Just a reminder, reading these books makes it difficult for you to make money on a practical level, but I have gained a lot of inspiration from them. Hydraulic cartridge valve manufacturer AAK, has gained insights into brain science and has been involved in overseas trade. AAK HYDRAULIC CARTRIDGE VALVES (647) 2023-08-12 https://www.aakindustry.com/info , -detail/hydraulic-cartridge-valve- manufacturer , s-aak647

Luca from Germany left a message on the website of hydraulic cartridge valve manufacturer AAK last Friday: Can AAK use 5-axis machine tool to produce valve cage for hydraulic cartridge valves? Luca conveyed 2 questions: whether AAK has a 5-axis machine tool and the valve cage of the hydraulic cartridge valve that he needs, is some particular. It is rare for us to receive this type of messages: using the equipment to delineate the production of cages for hydraulic cartridge valves. After communication, it was found that the hydraulic cartridge valves are to be used in their newly developed manifolds, with high precision requirements for the valve cage, which cannot exceed 2μm tolerance. In order to help the hydraulic cartridge valve manufacturer better understand his requirements, the production equipment was delineated in the inquiry, which posed a great challenge to the hydraulic cartridge valve manufacturers. The manufacturers without this equipment will be eliminated in the first round of selection. I remember that we took a video last year about the production of hydraulic cartridge valve cages by using DMG 5-axis CNC machine tool. At that time, it was a customized hydraulic cartridge valve for an Israeli customer. For the hydraulic cartridge valve with particular requirements for the cage, AAK used a German DMG 5-axis CNC machine tool. Its stable numerical control technology and stable accuracy were favored as treasures by our engineers. The processing speed reaches 20,000 rpm, with 5-axis linkage processing and equipped with a 30 position tool library. Its driving method is a direct drive ball screw drive, and all shafts adopt a linear direct measurement system to ensure that the valve cage processing accuracy is within 2μm. From the video, we can see that the technician first cleans the fixture with an air gun, then installs the hydraulic cartridge valve cage blank into the fixture, and then starts the machine tool. After processing, each valve cage needs to be measured and checked with a plug gauge. If the accuracy of the valve cage is qualified, it can be cleaned again with an air gun and then transferred to the next production process. After we sent this video to the German customer yesterday, he sent us the inquiry for a customized hydraulic cartridge valve today, with a very detailed drawing, which made us feel the rigor and professionalism of German customers again. How could it be possible for a hydraulic cartridge valve manufacturer to have no improvements if cooperating with such type of customers? This is also the benefit for hydraulic cartridge valve manufacturers working with customers with high quality requirements. AAK hydraulic cartridge valves, 5-axis equipment is ready for you, you can also try it out! AAK HYDRAULIC CARTRIDGE VALVES (760) 2024-01-16 https://www.aakindustry.com/info , -detail/hydraulic-cartridge-valves-aak760

Last week, Grayson issued a reorder for 120 hydraulic pressure reducing valves. Grayson is our Canadian customer. He has been engaged in hydraulic parts procurement for many years, and his colleagues trust him. In the second half of last year, their company developed a hydraulic power unit, and the accuracy of the hydraulic pressure reducing valve used is very high. Their original manufacturer of the hydraulic pressure reducing valves reviewed but advised immediately that he was not able to meet the requirements. Grayson later found a new manufacturer of hydraulic pressure reducing valves, and the sample approval process was very smooth. Unexpectedly, customers complained about the instability of the hydraulic system less than 3 months after the equipment was sold. After inspection, it was found that the hydraulic pressure reducing valve was stuck. The manufacturer of the hydraulic pressure reducing valves said that the hydraulic oil deteriorated, and the viscous substances produced increased the resistance of the relative movement between the valve body and the valve spool, causing the hydraulic pressure reducing valve to be stuck, but their Engineer detected that the hydraulic oil was normal. The hydraulic pressure reducing valve manufacturers did not cooperate, and Grayson had to find other new manufacturers to replace those bad hydraulic pressure reducing valves. Grayson contacted a number of hydraulic valve manufacturers, but there was no reply. He was in a bad mood. Grayson accidentally found AAK hydraulic valve in Google. He left a message on AAK website and asked, what are the reasons for the stuck of the hydraulic pressure reducing valves? I'm sure he's in trouble. After communication, I learned that he was cheated by the new manufacturer of hydraulic pressure reducing valves. The valve hole of hydraulic pressure reducing valves is not only the key quality point in processing and manufacturing, but also the processing difficulty. It can fundamentally affect the working performance, service life and stability of hydraulic pressure reducing valves. The hydraulic pressure reducing valve is stuck because of the coaxiality error of the valve hole during processing, resulting in the pressure imbalance in the matching gap between the valve hole and the valve spool, and caused the stuck problem. The valve hole accuracy of Grayson's hydraulic pressure reducing valve is required to be IT7 ~ 4. Most hydraulic pressure reducing valve manufacturers can't do it, but AAK is willing to challenge the high-precision hydraulic pressure reducing valves. Grayson saw the hope and asked AAK to send 10 hydraulic pressure reducing valve samples as soon as possible. After 30 days, 10 hydraulic pressure reducing valve samples were sent smoothly. After the samples were sent out, there was no comments from Grayson about AAK hydraulic pressure reducing valves. Nearly half a year later, Grayson sent the reorder of 120 hydraulic pressure reducing valves, which proved that the previous 10 samples of AAK were up to standard. AAK has a MICROSTAR FSH high-precision machine tool imported from Germany. The machining of the hydraulic pressure reducing valve hole can be completed (expansion - boring - boring - reaming - honing) with only one clamping. The final honing process adopts ultrasonic vibration honing. Compared with ordinary honing technology, it has the advantages of small cutting force, low cutting temperature, high cutting precision, long tool life and easy treatment of chips. The dimensional accuracy of the valve hole is IT7 ~ 4. AAK hydraulic pressure reducing valves have high precision and durability. You can also have a small try! https://www.aakindustry.com/info-detai , l/hydraulic-pressure-reducing-valves- aak231

Devante is from a Spanish hydraulic equipment manufacturing company, and has been engaged in procurement for more than 5 years. Last February, they upgraded an injection molding machine, focusing on the selling point of "high speed when empty, low speed when heavy load". The engineer asked Devante to purchase the hydraulic cartridge proportional needle valve of HydraForce. During the equipment commissioning, it was found that the pressure relief and flow of the hydraulic system of the equipment was conflicted with the hydraulic cartridge proportional needle valve, resulting in unstable operation of the equipment and jitter. HydraForce said that there was no time to customize the hydraulic cartridge proportional needle valve. Devante contacted several cartridge valve manufacturers and had no news. Devante was very worried. Devante browsed AAK website on Google and left a message: 1. Can AAK customize the hydraulic cartridge proportional needle valve, and the performance benchmarking HydraForce? 2. The function of smooth flow passage is required. 3. The function of variable flow gain is required. At the beginning, I thought that he was requested for AAK hydraulic cartridge proportional needle valve to benchmark the standard parts of HydraForce, but it was turned out that he needed us to optimize the standard parts of HydraForce. According to the equipment abnormality video, the original hydraulic cartridge proportional needle valve drawing, and their required functions sent by Devante, after discussion, AAK engineers was 90% confident. Devante asked AAK to make samples. After 40 days, AAK sent 15 samples of cartridge proportional needle valves. 2 months later, Devante informed that the market promotion of the upgraded equipment was smooth. Their engineers were satisfied with AAK hydraulic cartridge proportional needle valves, especially its variable flow gain characteristics, and smooth flow characteristics, small pressure impact during pressure relief, and accurate flow control. We mainly made 3 ingenious actions on the valve housing and valve spool, and solved the problem that HydraForce didn't want to do. 1. The lower part of the valve spool is arranged in the valve housing and sealed with the valve housing line. The upper part of the valve spool is connected with the control cover plate, the upper end of the control cover plate is connected with the valve cover with threaded holes, and the displacement sensor is installed on the threaded holes of the valve cover. The lower end of the valve spool is connected with the upper cavity of the valve spool. When the valve spool is at the lowest end, the valve is closed. When the valve spool moves upward, the valve gradually opens. 2. The lower end of the valve spool bottom is equipped with a semicircular slotted orifice. When the valve opening is small, the flow gain is small, and has good linearity, small flow, and high-precision linear control. When the valve opening is large, the flow gain is large, and it has good linearity, large flow and high-precision linear control to ensure the variable flow gain function of the hydraulic cartridge proportional needle valve. 3. The valve housing is provided with 4 symmetrical waist-shaped holes, replacing the conventional round holes. The oil flows in from the lower port of the valve spool and flows out through the waist hole, reducing the pressure impact and speed sudden change of the oil near the valve port of the hydraulic cartridge proportional needle valve, and realizing the function of smooth flow. AAK hydraulic cartridge proportional needle valve, has dual functions of variable flow gain and smooth flow. You can also try it! https://www.aakindustry.com/info-detail , /cartridge-proportional-needle-valves- aak473

There is a spread in the hydraulic valve industry: those who can do a good job in hydraulic valves may not be able to do a good job in hydraulic manifolds; those who do a good job in hydraulic manifolds, and basically can do a good job in hydraulic valves. Baptiste is from DMH France. The hydraulic manifolds purchased in Italy before was transferred to the hydraulic valve manufacturer who has cooperated for 4 years. However, he suffered from the 4 times a year after-sales of hydraulic manifolds. In the second half of last year, Baptiste purchased 30 hydraulic relief valves from AAK, which is the 4th time of purchasing in the year, and the quantity is the same every time. It is a little strange. After communication, I learned that a hydraulic equipment developed by them at the beginning of last year has stains on the hydraulic oil every few months, resulting in the jamming of the hydraulic relief valves. The replacement of 4 times a year keeps the customer complaining. According to Baptiste's description, the probability is that the hydraulic manifold design is improper. I suggested that he send us the hydraulic manifold drawing and system schematic diagram. Baptiste said that the hydraulic manifold drawing and system schematic diagram are confidential documents and he must get approval from boss before sending them to AAK. Three days later, Baptiste sent us the hydraulic manifold drawing and system schematic diagram, requiring that they should not be revealed to any other people. According to the analysis of the drawings, AAK engineers found that when the hydraulic power is input and the system does not start working, the hydraulic relief valve does not reach the opening pressure and cannot relieve the pressure, resulting in the increase of oil temperature and easy oil pollution. It is certain that the problem lies in the design of hydraulic manifold. I suggest redesigning the hydraulic manifold. The idea is as follows: AAK will change the 2 hydraulic relief valves on the hydraulic manifold block to use the hydraulic directional control valve alone, and change the oil circuit design. The principle is as follows: when the hydraulic system works, the hydraulic directional control valve cuts off the oil circuit, making the high-pressure oil enter the working branch. When the hydraulic system stops working, the high-pressure oil directly returns to the oil tank after passing through the directional control valve to realize zero pressure unloading. If the hydraulic manifold designed by AAK is not improved, no fee will be charged. Baptiste was a little interested after learning that. 45 days later, AAK sent a new hydraulic manifold. 4 weeks later, Baptiste informed by email that the hydraulic manifold of AAK had been used for 1 month, the hydraulic oil had no pollution, the whole hydraulic system was more sensitive, and the problem that had plagued them for 1 year was solved at one time. AAK hydraulic manifolds had been tested for first-line brands since 7 years ago. If meeting the following 3 points at the same time, there may be no second hydraulic manifold manufacturer in Ningbo except for AAK: 1. AAK technical team has engineers from the world's top 500 hydraulic manifold enterprises. They have their own experience in material selection, production drawing design, oil circuit design and production quality control. 2. Before hydraulic manifold assembly, the valve block shall be deeply cleaned to ensure 100% impurity free. Each valve shall be tested. 3. Only technicians with more than 10 years of experience are qualified to assemble the hydraulic manifolds. After assembly, use the test bench to debug the hydraulic manifolds for many times to ensure that the act function of the circuit is accurate and reliable. Baptiste privately informed that the boss was very satisfied that he found a reliable hydraulic manifold manufacturer, solved the after-sales troubles of the whole year, and could be promoted to the manager of the procurement department next month. Baptiste was so happy. AAK hydraulic manifold block is professionally designed to save you worry and effort. You can also have a small try! https://www.aakindustry.com/info-detai , l/hydraulic-manifolds-aak230