Other Machinery & Parts

This bag making machine is specially for various of bag,such as diaper bag,hand holding bag,soft loop handle drawing bag and so on. The machine main control center adopts PLC and touch screen to display bag making speed,bag making length setting and automatic bag making counting. The machine is equipped with 2 sets of punching frame devices and 2 sets of photoelectric frame devices. Only use this multifunction bag making machine to produce what you exactly want.Not only it can save labor but also improve your project. Main technical Parameters Material LDPE,HDPE,etc. Unwinding Width within 1580mm Unwinding Diameter within 800mm Machine Speed 80pcs/min Bag Width within 600mm Bag Length within 550mm Bag Speed 300-400m 60-65pcs/min Power Supply 380V50Hz Total Power 20KW Machine Weight 4500KG

Speed Regulation Movable Cement Grouting Machine Manual Flow Stability Cement Grouting Machine Manual Features of Cement Grouting Machine Manual: 1. Maintenance downtime: When the grouting pump is not used for a short or long term, the pump head should be disassembled, cleaned and brushed with antirust liquid or grease before reassembly for later use. 2. Disassembly and installation method: Remove the four fastening bolts connected with the pump head and the cylinder, and remove the material cylinder and the inlet and outlet of the slurry. Remove the connecting bolts between the inlet and outlet of the slurry and the pump head respectively, and take out the steel ball, sealing gasket and the "O" rubber ring for end face sealing. Clean up the removed parts in time, and install them in reverse according to the above method after rust-proof treatment. Please pay attention not to damage the seals when disassembling. Model SYB Cylinder diameter 80mm Motor power 11kw Grouting capacity 27-100 L/MIN Outlet pressure 5-8Mpa Outlet diameter 19mm Inlet diameter 25mm Cylinder number 2 Particle diameter size ≤5mm Suction Height 2.5m Weight 490kg

Swimming pool heat pumps capture the heat from the air and transfer it to your swimming pool water. Swimming pool air source heat pumps are an energy-efficient means of heating your pool water; you can obtain up to 6 units of heat for every single unit of electricity used to power them. Heat Pump Features: Automatic heating/cooling High efficiency compressor COP UP TO 6.0 Automatic defrosting R410A refrigerant Titanium heat exchanger Down to -10℃ operation Strong steel casing Very quiet operation

The mini heat pumps are the new models of heat pumps available in the swimming pool market. These Guangteng heat pumps are installed very easily and do not require previous installation and specify a By-pass. It is a Plug & Play product that is placed on the same circuit as the pool filtration. They are economic and very effective. Mini Heat Pumps Features: Plug & play design, easy to operate COP UP TO 6.0 Environmental R32 refrigerant Titanium heat exchanger to resist corrosion of pool water Portable 21kg mini heat pump, easy to transport Press and heat, easy to control

Our EVI DC inverter heat pump is a solution which uses DC inverter technology to heat, cool and to produce domestic hot water. It does not only satisfy house heating requirements, but also supplies domestic hot water. Besides, it can provide you a cooler environment in a hot summer. You will enjoy a comfortable life at your home all year round with one device. Guangteng Heat Pump can operate in minimum outdoor air temperature of -25℃. Leaving water temperature up to 60C for radiator and domestic hot water applications, making hot water readily available Air Source Heat Pump Features: DC inverter technology EVI technology, down to -25℃ operation R410A refrigerant SWEP plate heat exchanger ERP A++ For heating, cooling and DHW

What is a monobloc heat pump? The multi-function heat pump is with inbuilt storage tank, expansion vessel and WILO circulation pump in one unit. Its installation is simple and it can save installation space. It's a high efficiency and cost-effective alternative for heating, cooling and DHW production. ALL-IN-ONE, YEAR-ROUND HEATING, COOLING AND DOMESTIC HOT WATER SUPPLY SOLUTION Monobloc Heat Pump Features: High efficient compressor of brand named Brazed plate heat exchanger of SWEP brand With inbuilt buffer tank With inbuilt expansion vessel With inbuilt WILO circulating pump Electronic expansion valve to regulate refrigerant Four way valve reverse defrosting automatically

Air Cooled Water Chiller PRODUCT DESCRIPTION High efficiency air cooled chiller units engineered for heavy-duty industrial applications. The units are equipped with world class components, including high efficiency scroll compressor of PANASONIC, brazed plate heat exchanger of SWEP. The integral programmable control system assures reliable operation and temperature control under the most demanding conditions and extreme environments. Where aesthetics and environmental conditions or water access restrictions exist, the air-cooled chiller may be applied. Both air-cooled and water-cooled chillers depend on an air stream as a means of heat transfer. The air-cooled has lower water consumption than the water cooled. Here are the of using air-cooled chillers benefits: No cooling towers Better environmental stability-no water wastage Low maintenance costs Easier to operate and control-tower freezing and tower bypass absent Chemical costs avoided Water costs avoided, especially in cities No water problems to deal with in case of disaster

1000 KG Loading Heavy Duty Storage Racks Logistic Equipment Workshop Factory Pallet Racking System Contact us, we can provide you with design drawings and quotations! Product Name 1000 KG Loading Heavy Duty Storage Racks Logistic Equipment Workshop Factory Pallet Racking System Material High Quality Cold-rolled Steel Size Customized for 1000 KG Loading Heavy Duty Storage Racks Logistic Equipment Workshop Factory Pallet Racking System Color Customized(Regular colors are orange, blue and silver grey) for 1000 KG Loading Heavy Duty Storage Racks Logistic Equipment Workshop Factory Pallet Racking System Remarks Different color, sizes, layers, and thickness of material are available. Quality Control is 100% checked for 8 times Acshelfpted ODM or OEM .

Model No. ZKGL-80-12 Aluminum tube size (mm) Chamber size (mm) O.D.80*1000 Length 300mm Power supply 220V/4KW Max. temperature 1200 ℃ Continuous temp. 1100℃ Heating rate ≤ 25℃/min ( suggest 15℃/min for longer life using of furnace ) Accessories One pair of high temperature furnace gloves; One piece of furnace hook One set of Stainless Steel Vacuum Sealing Flange Kit Optional devices Paperless recorder Quartz Boat Vacuum Pump 1. Furnace material is high-purity alumina ceramic fiber materials, new assembly structure, no transformation in long term high temperature, sturdy and durable 2. Vertical or horizontal operation freely adjustable; working height freely adjustable, 3. Operation also possible separate from stand if safety guidelines are observed 4. Control system integrated in furnace base 5. Defined application within the constraints of the operating instructions 6. The heating element is made of high-quality alloy wire, which can bear large load, stable and long service life 7. The furnace tube adopts quartz tube as carrier and the stainless steel flanges on its both ends are simple design, reasonable, easy to disassemble and convenient for entering and leaving sintered samples

Hydro turbine generator is droved directly or indirectly by hydro turbine. The rotating speed is less than 1500r/min, with horizontal and vertical arrangement. Excitation mode with brushless and static silicon type. Components including stator, rotor, base frame, bearing, excitation motor or collecting ring. The outlet voltage from 400V to 13.8KV, and frequency could be 50Hz or 60Hz, output from 50Kw to 50Mw. Our generator are high efficiency, reliable, manufacture and tests all follow related IEC standards. Place of Origin: Sichuan, China Brand Name: Customized Warranty: 1 year Application: Hydropower Plant Certificate: ISO9001 Lifetime 35 years Main Features 1) Simple structure ,easy in installation and maintation. 2) Adopting high quality material with high efficiency. 3) Optional color ,type and material. 4) Professinal advice to the most suitable generator according to the station parameter. 5) Long lifespanof 30----50 years.

Computer plate making machine, appearance size: 1400*1200*1150, processor size: 1200*1100*1150. Basic parameters of the host: maximum output size: 1130*920, minimum output size: 400*350. According to the maximum output size, it can reach 24 plates per hour, accurate and clear. Imported V6 laser is used. Parameter settings of the processor, temperature: 23-25 degrees Celsius, flushing time: 22-26 seconds. Make an appropriate adjustment according to the time of use of the chemical. The machine uses a standard 220V voltage, the room needs about 30 square meters, keep the room dry, and a constant temperature of 22 degrees Celsius. Model Thermal UV T824 T832 T848 T864 T8128 U824 U832 U848 U864 U8128 NO.of lasers 24 32 48 64 128 24 32 48 64 128 Throughput(1130*800) 13 18 23 28 45 13 18 23 28 45 Max.Min.Format MAX:1160*940 MIN:400*350 MAX:1160*940 MIN:400*350 Laser source 830nm 405nm Resoiution 2400DPI Loading system Automatic,Semi-Auto(Optional Auto-loader) Plate requirement CD. 0.15-0.4 (Thermal plate) CD. 0.15-0.4 UV plate Interface 1-bit Tiff interface and direct workflow driver,support CIP3/CIP4 Power AC220V,50-60HZ 5.5KVA Work environment Temperature:20-25℃,Humility:40%-80%

PP strap production line /PP strap manufacturing machine, PP strap making machine PP strap with width from 5mm to 19mm can be manufactured by our PP strap manufacturing machine. we furnish PP strap production machines with 1, 2, 4 and 6 PP straps extruded. NO. Component Feature1 Feature2 1 Drying dehumidifacation crystalization system Energy efficiency Feeding devices Self-adjustment of the system Rapidity in production shift Optimal and continuous mixing of the material No risk of contamination 2 The three components mixing and feeding unit Automatic Increase IV With automatic ratio mixing system for raw-material additives Use-100% bottle flakes 3 extruder Sevo-extruder can save electric 30% Low tempreture plastify High efficiency screw No deformation at high temperature 4 Back-flush screen changer Continuous Back-flush screen changer make the produce non-stop Full automatic self-cleaning optimal design of the melt flow way - short melt residence time low pressure build up - to prevent thermal variations of the melt no dead spots for fast changes of material or color operational reliability and long durability 5 Melt measuring pump world's leading elastomer extrusion pumps over 100 years experience Protect extrusion equipment reduce energy consumption Provide accurate system pressure for the mold Continuously obtain stable product quality 6 Cooling tank Stainless steel/Lifting tension/ water removal system to maintain tension 7 Stretching machine Frequency control mold tempreture machine control roller surface tempreture 8 stretching oven High-performance insulation layer save energy Maintain the constant tempreture of the strap 9 Embossing device High-precision make strap with goof friction Ensure the accuracy and consistency of strap pattern Enhance the friction for strap Enhance the strength for strap Unique technology World leading high precision standards 10 winder Sevo-motor controls winder dispalcement width and distance Increase the value of strap Manual control or computer control is optional Servo wiring is set by computer according to strap specifications Automatically adjust the winding tension The winding curve of the strap reel is perfect

Laser cutting machine introduction Laser cutting machine is a new type of metal processing thermal cutting machine. It uses working gas and high-speed and high-temperature plasma arc as a heat source to partially melt the metal, and uses high-speed airflow to blow away the molten metal while forming a narrow plasma cutting seam. The tool is used to cut various metals, such as carbon steel, stainless steel, copper, aluminum, cast iron, etc. It not only has the advantages of narrow cutting seam, fast cutting speed, small heat-affected zone, smooth cutting, small deformation of the workpiece, simple operation, etc., but also has significant advantages and energy-saving effects. It is suitable for all kinds of machinery, metal structure manufacturing, repair and installation services, sheet metal manufacturing, drilling, excavation and repair, chamfering and more metal cutting projects and plans. Parameter information Machine Model RG-30120 RG-40120 RG- 45150 RG-45200 Working Area 3000x12000mm 4000x12000mm 4500X15000mm 4500x20000mm Laser Power 3000- 20000W Max Linkage Velocity 100m/min Z Travel 150mm Positioning Accuracy ±0.03mm Repeat Positioning Accuracy ±0.02mm Max Acceleration 0.8G

Pure oxygen burner 1. Applications: 1) This burner has uniform and dispersed flame, with high peak temperature and uniform heat transfer. Compared with the conventional air combustion burner, the fuel consumption can be greatly reduced; 2) This burner can flexibly adjust the flame shape and temperature distribution, and reduce NOx emission by eliminating the adverse effect of nitrogen on the combustion process.   2. Product Features: 1) Enhanced heat transfer and heat transfer control, high thermal efficiency; 2) Reduce fuel consumption; 3) Improve melting efficiency / heating efficiency; 4) Reduce the emission of pollutants (clean and complete combustion) and reduce the volume of exhaust gas (up to 70%); 5) Simple maintenance and low cost; 6) Low equipment investment, such as reducing the cost of waste gas treatment device and flue gas waste heat recovery device.