Other Industrial Equipment

Automobile assembly line According to customer needs, we can develop and design fully automatic or semi- automatic non-standard special assembly equipment for the whole vehicle manufacturing process, so as to reduce employees, improve cycle time, and improve product consistency. It can not only save costs for production enterprises, but also improve efficiency and product quality. Automobile assembly is the last link of all the manufacturing processes of the whole vehicle, and it is also a relatively important link. It is the process of combining thousands of parts that have been inspected and tested according to the specified precision standards and related technical requirements into some large and small assemblies, and then assembling these assemblies into automobiles. In this process, each procedure must be strictly tested to ensure that it is qualified. The advantage of a car, in addition to relying on advanced product design and well-manufactured parts, is also indispensable to a good assembly process. The assembly production organization, production line, equipment, detection means, assembly automation degree, etc. will all be important topics in the research of automobile manufacturing. There are many kinds of parts in automobile assembly, the quantity is large, and the operation is relatively complicated. In addition to large systems such as engine, transmission system, suspension, body, steering system, and brake system, interior parts, electrical appliances, wiring harnesses, software, etc. must also be assembled. tube, glass etc. The content includes interference fit, welding, riveting, inlay, screw connection, etc. Therefore, the workload is still very large (generally accounting for about a quarter of the entire automobile manufacturing workload). Generally speaking, the automobile assembly process mainly includes the following major assembly lines: engine assembly line, door subassembly line, instrument panel subassembly line, interior decoration subassembly line and rear axle subassembly line, and which final assembly line is thickened and the final Test line. The final assembly line is composed of interior decoration line, chassis line, exterior decoration line, door line, inspection line, rain line, etc. The following is a detailed introduction of the automobile final assembly line: Assembly interior line: Assembly chassis line Assembly door line Automobile Assembly Line Automotive EPC 0

PRODUCT DESCRIPTION THIS IS NEW TYPE GABION MESH MAKING MACHINE IN 2023. Min.output: 250m/hour Max.wire diameter 4.00MM power:30kw Size:7200x1400x240 , 0mm Weight:approx.19 ton

Automatic Galvanized Shutter Door Keel Cold Roll Forming Machine A). Main Specification Material thickness: 0.55-1.0mm PPGI, 0.7-1.2mm aluminum Decoiler: Manual or hydraulic decoiler Weight capacity of uncoiler: 5 Ton Forming Speed: 6-8m/min Forming Station: 14 stations Drive: Chain transmission Main power: 5.5KW Cutting: Hydraulic cutting Cutter material: Cr12Mov, Quenched HRC58-62 PLC: Panasonic Brand Support table: Simple Nonpower type Machine weight: about 6Ton B). Working Flow of Clip Lock Roll Forming Machine Decoiler - Slitting & Cutting - Feeding - Roll Forming For One Side - Roll Forming For The Other Side - Roll Forming For the Middle Rib - Runout Table C). Applications Standing seam roof panel; bemo panel; bemo roof panel; tapered bemo panel; tapered sheet; tapered roofing sheet; metal roof panel; steel roof panel; roof wall cladding; roof cladding; wall cladding D). Competitive Advantages High Quality Reasonable Price Good after Service Factory Visit 1 Year Warranty More Than 10 Years Experience E). Reference Pictures Door Keel Cold Roll Forming Machine Automatic Galvanized Shutter 0Door Keel Cold Roll Forming Machine Automatic Galvanized Shutter 1

Automatically Slag Discharging With Operating System With CCS And RMS Certificated Separator For HFO Marine Company Information We are one of the world's leading manufacturers of disc centrifuges, decanters, separation systems for land power station and container typer power plant. We focus on the necessary equipments on the power station, environmental protection, energy recycling, chemistry and etc. Now, there are over 150series of decanter centrifuges and disc separators used home and abroad. Technical parameter: Fuel Oil Separator is mainly used to remove water and mechanical impurities(cat fines) from diesel oil, lubricating oil, heavy fuel oil(HFO) and other mineral oil in marine diesel engine unit and land-used diesel generator unit of power station so as to reduce wear of the diesel engine and other machine, and prolong engine life. The model is also used to separate two unsolvable liquids with different specific gravity or remove small amount of solid particle from liquid. We have the following advantages: 1. After separation,it could reach that the maximum water content in the output is 0.3%, and the maximum solid particle is 0.03%.This is also the CCS standard.And we could provide CCS certificates and RMS certificates to prove their function and usage. 2. We could make the HFO to 720CST,the separation effect feedback is very good 3. We are the first and largest company handling industrial oils in the country, and we have been involved in setting standards for the shipyard industry 4. The oil we handle is above national standards,all Marine diesel engines on Chinese ships are supplied by us 5. Our separator can be adjusted by no specific gravity ring or specific gravity ring adjustment, automatically calculating the slag discharge time and equipped with Intelligent operating system for operating easily. And more... Automatically Slag Discharging With Operating CCS RMS Separator For HFO Marine 0 Discharging type Manual discharging Max capacity L/h 14000(0# diesel oil) Motor power Kw 11-15 N.W. kg 730 Volume of the slag cavity L 2 Discharge type Variable discharge Type of output Centripetal pump Installation dimension L × W × H (mm) 1200x810x1225

Professional Printed Circuit Board PCB Pneumatic Nibbler with Pneumatic Control Printed Circuit Board Nibbler Machine Specifications: Action stroke times 12 times / min Working dry air pressure 0.50-0.70 Mpa Slide stroke 2 mm PCB Nibbler Machine Weight 2 kg PCB Nibbler Machine Size 280x105x185mm Printed Circuit Board Nibbler Machine Features: 1, all pneumatic control, easy to operate 2, suitable for slitting various PCB connection points 3, hook blade work, hook blade shape can be customized 4, convenience for replacing hook blade 5, hook blade for "T" type or "L" type blade 6, small size, does not damage the part of the PCB and PCB substrate Safe operation with PCB nibbler CWV-LT The PCB is slipped with its milled groove over the blade and is placed onto the matrix. The off-cut is pulled under the blade. When the foot switch is pressed, the off-cut is punched out and the waste material is collected inside the machine. "T"-Blade TTTTTTTTTTTTTT. , jpg With the T-blade off-cuts can be punched out right and left of the blade without turning the PCB. "L"-Blade LLLLLLLLLLLL.jp , g The L-blade will be used if there are small distances between the off-cuts Matrix MMMMMMMMMM.jpg

Customized Sand fully automatic autoclave Building Materials Production Line AAC BLOCK MAKING MACHINE INTRODUCTION what is AAC? Sand AAC Block Production line 2013 Fly ash AAC block production line price The Autoclaved Aerated Concrete (AAC) material was developed in 1924 in Sweden. It has become one of the most used building materials in Europe and is rapidly growing in many other countries around the world. Autoclaved Aerated Concrete, also known as Aircrete, is a lightweight, load- bearing, high-insulating, durable building product, which is produced in a wide range of sizes and strengths. AAC offers incredible opportunities to increase building quality and at the same time reduce costs at the construction site. AAC is produced out of a mix of quartz sand and/or pulverised fly ash (PFA), lime, cement, gypsum/anhydrite, water and aluminium and is hardened by steam-curing in autoclaves. As a result of its excellent properties, AAC is used in many building constructions, for example in residential homes, commercial and industrial buildings, schools, hospitals, hotels and many other applications. Autoclaved aerated concrete is actually hydrated calcium silicate. The calcium is obtained from quick lime, hydrated lime and cement. The gypsum is used as a catalyst and for optimizing the properties of AAC. The silica is obtained from silica sand, fly ash (PFA), crushed silica rock and/or stone. It is possible to obtain silica as a by-product from other processes, e.g. foundry sand or burgee from glass grinding, provided the levels of alkalis or other impurities are not too high. This product is key equipment which has a widely application in building material factory to autoclaved cure different kinds of building materials. It is also used in areas of chemical, textile, wood, metallurgy, military industry. Convenient operation, security and reliable are its advantages. AAC BLOCK PRODUCTION LINE RAW MATERIAL INTODUCTION AAC block machine main material:coal ash sand waste mine material coal stonestone dust and other silicon materials. 1 Product weight is according to 600kg/m3 to control. 2 annual capacity 200,000M3. 3 set raw material proportion: cement 6.5%, raw lime 23%, flyash 68%, gypsum 3%, aluminum paste powder 350g/M3. 4 water and material rate 0.631 5 one mould product 2.88M3 6 Casting slurry cycle time 5-6 minutes, cut cycle time 5 minutes. 7 casting slurry temperature 38-42 degree 8 body quiet stop. Time is 1.5-2.5housr, temperature 50-90 degree, after quiet stop body strength is 0.15-0.18Mpa 9 Steam curing cycle time, come in and out autoclave about 0.5hour, steam curing cycle time about is 6 hours/1.6Mpa, total 6.5 hours. Customized Sand fully automatic autoclave Building Materials Production Line for wood

Plastic Extruder Extrusion Line / PVC PP PE Double Wall Corrugated Pipe Extruder Making Machinery 1. Special designed screw and mould; the convenient and reliable changing of the mould have solved the problems of easy wear of the barrel and hard foamed of the material; the corrugated forming mould blocks that touching the pipe are cooled by inner circulation water, higly increases the forming speed; use Korea Autonic meter counter for accurate metering; the complete production line is running fast, stably and easy to operate. 2. Process flow Raw material + additive → mixing → vacuum feeding machine → hopper dryer → single screw extruder → color code extruder → mould and calibrator → vacuum forming machine → cooling tank → haul off machine → cutting machine → discharging rack 3. It is adopted horizontal structure with shuttle type transmission, SEIMENS control system, airtight water cooling system and vacuumizing forming, which assured very quick cooling and high output in production process. We also make the original design of two layers belling on line with proffetionally auxiliary equipments. Technical parameter: Item Details Capacity 200kg/h Forming Way Vacuum System Control Way Electric control or computer control Line Speed 3-6m/min Diameters ID 32mm to ID 110mm Application: 1. A corrugated pipe is a tube with a series of parallel ridges and grooves on its surface. This pipe can be manufactured of plastic such as high-density polyethylene (HDPE) or PVC. It can be coated or lined. Corrugated pipe is used in applications such as drains where flexibility, durability, and strength are important attributes. 2. Small size corrugated pipe can be seen in familiar uses such as the drain pipe used to carry runoff from gutters on the eaves of a home. Larger size pipes are used as storm drains and culverts under bridges and alongside roadways. The flexibility of corrugated pipe makes it more suitable for a variety of uses than rigid smooth pipe. The degree of corrugation is measured by the height of the ridges; The higher the number, the more flexibility the pipe. Our company competitive advantages : FAQ: Q1:Are you a trading company or a manufactory? A1:We are a manufactory,so we can give u the best service . Q2:What's your guarantee or the warranty of the quality if we buy your machines? A2:We offer you high quality machines with 1 years guarantee . we will give you spare part free in 1 years Q3:When can I get my machine after I paid? A3:We will deliver the machines on time as the date we agreed both side. Q4:How can I install my machine when it arrives? A4:We will send our engineer to your side as soon as you get all your machines ready , for testing and teaching your technicians how to run the machines. Q5:How about the spare parts? A5:After we deal down all the things , we will offer you a spare parts list for your reference. PVC PP PE Double Wall Corrugated Pipe Making Machine 0

Floor Sanding Cloth Rolls 100 Grit , Zirconia Aluminum Abrasives Quick Detail: WEEM 3126-22 Premium Floor Sanding Rolls are designed for floor sander machines, like: Squar-Buff, Clarke, Deva, Silver Line, Floorking M101-24 and so on. Description: WEEM 3126-22 Premium Floor sanding Rolls are built with self-sharping Zirconia Aluminum gain, resin over resin, close coated on durable, and heavy duty Y weight waterproof polyester backing. It is cut to width of 12”, which fits sheet sander machine: Squar-Buff, Clarke, Deva, Silver Line, Floorking M101-24 and so on. Self-sharping Zirconia gain heavy duty structure requires heavier pressure to break down the self-sharpening grains. It is ideal for heavy grinding on hard woods. This abrasive can last up to 5 times longer than aluminum oxide on tough applications for heavy stock removal to finishing sanding. A closed coat product has a higher number of abrasive cutting points per square inch and results in higher stock removal rate and longer time before the abrasive wears out. Normally results in a better finish. Specifications: Part Number: 3126-22 Backing: Y weight waterproof polyester Treatments: Anti-static Coated: Close coated Bond: Resin over resin Grain: Zirconia Aluminum Grit: P36~P100 Width , : 12 inch Length: 25 yards Applications: Floor sanding, Sheet sander Competitive Advantage: It is made for floor sheet sander such as: Squar-Buff, Clarke, Deva, Silver Line, Floorking M101-24 etc. Fast cut sanding and excellent performance

XL Monopile 2000t Assembling Rotator Offshore Foundation Fit Up Welding Production Line Brief introduction: Heavy duty 2000t assembling rotator special for offshore foundation XL monopile final assembling process. Composed by 1set welding rotator (work load limit 2000t for 1power & 1 idler ) & 1set fit up rotator (work load limit 700t/idler) Monopile Offshore Foundation Welding Production Line 2000t Assembling Rotator 0 Description: Composed by 1set 2000t welding rotator (1power & 1idler) & 1set 1400t fit up rotator (2idler).Total 1power & 3idler. All idler rotators are with hydraulic lift cylinder. 1power & 1idler working load limit 2000t; The other 2idler working load limit 700t/idler; Power rotator install motorized trolley. Traveling capacity 2000t; All idler rotator install idle trolley mobile on the rail; All the wheels are forged steel roller. Monopile Offshore Foundation Welding Production Line 2000t Assembling Rotator 1 Monopile Offshore Foundation Welding Production Line 2000t Assembling Rotator 2 Feature: Power rotator is double-motor driven, the roller driver adopt cycloidal planetary gear reducer. All idler with hydraulic liftable cylinder, effectively adjusting the MP position, aligning the joint edge. Wheel material is special material forged steel suitable for heavy duty work piece. With motorized trolley,able to take the monopile mobile along with the rail. Realizing ground logistic to decrease the crane/hoist using. The 2000T assembling rotator adjust the center distance by reserved screw holes in order to adapt to diameter of work piece. Production line 2000T offshore XL monopile Composed 1drive unit + 3idler unit (hydraulic lift) Max. Loading capacity 2000Ton (1power & 3idler) Workpiece dia. range ø3,000~ø10,000mm. Wheel material Forged steel Roller center distance 2100~4500mm The distance between ground and rotator center 1,850mm ( Return to zero point.) Roller center moving distance and adjustment method 1.The idler roller seat is fixed by bolts. 2.Adjust the center distance of the roller with bolt holes. 3.Roller seat moving distance is 150mm. Rotator walking method 1. One unit of rotator is electric walking and the other one is unpowered walking. 2. When the roller bed is walking, the maximum load is 1000 tons. 3. A group of rotator can move on the track at full load. 4. Electric walking speed is 230mm ~2300 mm/min Group pair lifting drive Hydraulic. Hydraulic station 1.Independent hydraulic station for each rotator. 2.Each hydraulic cylinder is equipped with an independent oil pressure gauge, and there is a comparison table of pressure-convertible load, which is recorded in the manual. Rotator control function 1.Low voltage (24V) wired (30M)/wireless remote control (100M). 2.Control cable length 30m, and must be provided a set control cable for spare parts. 3.The grounding of the electrical components of the control box must meet the electrical code requirements. 4.Cylinder lifting stroke and walking control. 5.Stop & E-stop button and synchronized function. 6.The remote control must have the above functions. 7.If the wireless remote control is damaged, it can use the wired control to operate. 8.Each hydraulic cylinder can operate independently and with linkage capability Electronic control part 1.Hydraulic station and power control box need to be protected. (windproof, dustproof, waterproof) 2.Electronic control box and elements can be fast disassembled. 3.The electronic control box and components need to adapt to the subtropical & island-type climate. 4.Perfect protection circuit (windproof, dustproof, waterproof). Transmission & gap protection Windproof, dustproof, waterproof. Rotator weight and lifting method 1.The weight of the rotator must be clearly marked on the drawing and sprayed on the rotator. 2.The rotator needs to provide and set the ideal lifting position and method and mark it on the drawing Rotator stabilization and anti-roll device 1.Set holding track device, the design drawings must be provided and recorded in the manual. 2.A stable device in contact with the ground is required at the periphery of the rotator. 3.When the rotator is fully loaded and not moving, the rotator can be stabilized. Protective Need to set up a variety of protection devices, such as ELCB, Electrical fuse, and so on. Maintenance spares 1.Must be used international label. Application: Offshore foundation XL Monopile Offshore wind tubular tower Petrochemical column Bullet tank Pressure vessels Chemical & fuel storage tank fabrication Any heavy cylindrical job Competitive Advantage: With lubrication system. VFD rotary speed control, improving the reliability of operation. Steel or PU roller which can ensure a long time using (at least 2 years). Inverter and main electric elements are Siemens/Schneider or equal brand. Accept testing before delivery. Accept special design and custom. Monopile Offshore Foundation Welding Production Line 2000t Assembling Rotator 3 Monopile Offshore Foundation Welding Production Line 2000t Assembling Rotator 4 Monopile Offshore Foundation Welding Production Line 2000t Assembling Rotator 5 Monopile Offshore Foundation Welding Production Line 2000t Assembling Rotator 6 Monopile Offshore Foundation Welding Production Line 2000t Assembling Rotator 7 What Ronniewell can do for Ronniewell customers: Give you high quality products. Give you five-star price. Give you suitable recommendation. Give you good after-service. Give you professional technical guide. Warmly welcome you visit our factory. Points you may concern: Customization - Can your machine or other products be customized? Ronniewell: Sure. As a professional manufacturer, we have our own engineer team, who is good at design, develop & build special solution catering for your individual requirement. Transportation-What about the transportation? Ronniewell: Seaway is the most common transportation way for oversea trading. Depends on your location, combined transport by rail and sea is also an option. Certainly railway transportation is also acceptable if it is the most suitable approach. After sale service - What about the after-sale service? Ronniewell: We provide 12month guaranty period for the whole machine quality. During this time, any issue proved because of the machine flaw itself,we would take the whole responsibility of it. Except of the guaranty period,technical advisory support is available freely covering the whole using life of the machine. Engineer service on user premises is also available for necessary.

Cinhpump Silent Micro Air Pump Mini Electric Long Lifetime Air Pump Quick Detail: 15L/m air flowrate 30kpa air pressure Double diaphragm, duckbill valves Aluminum body Continuous working day and night Warranty lifetime 10,000hours or 2years size:106x76x74 mm weight:0.7 kg Outlet & Inlet Dia: 0.3" (7.6 mm) Description: Cinhpump Silent Micro Air Pump PMA-15 series use a unique linear motion design that has the capability of over 20,000 hours of continuous maintenance-free operation. They are compact, cool and highly reliable and inexpensive. Features: Compact size Steady air outputs with low noise Very low vibration Low power consumption Economical Applications: intermittend pneumatic compression(medical) compression therapy ozone generator aquarium recovery system fragrance diffuser air bed Atmospheric Detection Dosing chemical material air massage instrument medical applications industrial applications household appliance Specifications: Air Output: 30SCFH(15Lpm) Pump Pressure: 4.5PSI(30kpa) Power Requirement: AC220V,AC120V, AC24V or AC12V, 50Hz or 60Hz or DC12V / DC24V with our mini power inveter. Power Consumption: 10W Pump Design: Double diaphragm, duckbill valves Pump Body: Aluminium Outlet & Inlet Dia: 0.3"(7.6mm) Electrical Connections: 1-ft(300mm)Insulated wire pair Noise Level: 40db unconnected, connected operation will reduce db level Dimension(LxWxH): 4.2"x3"x2.9"(106x76x74mm) Ne , t Weight: 0.7kgs Performance Curve Cinhpump Silent Micro Air Pump Mini Electric Long Lifetime Air Pump 0 Cinhpump Silent Micro Air Pump Mini Electric Long Lifetime Air Pump 1 Competitive Advantage: long lifetime, low noise, high quality, 15L/M air flowrate and 30kpa pressure.

SS316 Softgel Capsule Machine / Automatic Capsule Machine For Pharmaceutical Enterprises Non animal Softgel Encapsulation Machine For 50000 - 70000 Capsules / H Vegetable Gelatin Softgel Encapsulation Machine For 50000 - 70000 Capsules / H Quick Detail Product Name Soft capsule Filling Machine Power consumption 13 kw Control Mode PLC+Touch screen Plunger Numbers 12 Dimension 880X2200 , X2000mm Dosage deviation < ±2% 7 Inch Electric Encapsulator Machine For Pharmaceutical Enterprises 0 Product Description S407 Softgel Encapsulation Machine is developed based on Model S406 softgel encapsulation machine. The die roll length is 20mm longer. It combines advantages of foreign equipment and requirements of customers,considering the needs and the biggest benefits of customers as start point.There are following features besides S406’s. S407 adopts PLC operation, making operation more convenient. The die roll’s rotation rate can be regulated within 0 to 7 rpm, so users can choose the most proper rotation rate according to data of different material and techniques. Drying cycle is controlled by PLC unified, so users can regulate the cycle time conveniently. The tumbler dryer is designed with a device to remind operators to prepare well when discharging. S407 can realize the function of statistical statements and printing. The machine drive system’s lubrication pump is droved by motor alone, which greatly improves the lubrication performance when main equipment operating at a very slow speed. At the same time, it can reduce machine vibration, prolong machine overhaul time and save investment for users. Specifically speaking, it has the following characteristics: Dosage deviation:< ±2% Material of oil roller: porous stainless steel Parallel degree of main shaft of the die rolls:<0.02mm Micro gelatin ribbon oil lubrication Precision temperature control for injection wedge, spreader box and chilled water. The running parameters can be stored and recalled with a finger tip touch if necessary. Pneumatic wedge lift up. Pneumatic left die shaft movement. 7 Inch Electric Encapsulator Machine For Pharmaceutical Enterprises 1 Application It’s mainly for softgel making enterprises and pharmaceutical enterprises and universities. Specification Model S407 Die roll Ф103X172mm Die roll speed 0~7rpm Plunger numbers 12 Overall dimension 880X2200X2000mm weight , 1200kg Power consumption 13kw Control mode PLC+Touch Screen Output rate 8#OV 50000-70000 pcs/hour for animal gelatin 8#OV 30000-50000 pcs/hour for animal free gelatin Soft capsule/softgel making machine, paintball making machine, Tumble drying machine, gelatin melting tank 7 Inch Electric Encapsulator Machine For Pharmaceutical Enterprises 2 7 Inch Electric Encapsulator Machine For Pharmaceutical Enterprises 3 7 Inch Electric Encapsulator Machine For Pharmaceutical Enterprises 4 7 Inch Electric Encapsulator Machine For Pharmaceutical Enterprises 5

High Efficiency Silica Gel Wheel Industrial Desiccant Dehumidifier With Cooling Coil Quick Details: Style: Refrigeration combined with Wheel Desiccant Rotor: Sweden Proflute Desiccant Material: Silica Gel Wheel Rated Air Flow: 6000m³ /h Supply Air Parameters: T=25℃ RH=20% Dehumidifier Quality: High Installed Power: 49.1kw Voltage: 380V, 3 phase, 50Hz or customized Certification: ISO9001:2008 Features: Economical, energy-saving Usage: Air temperature and humidity control General Description: ZCB Series Desiccant Dehumidifier System removes humidity using both refrigeration and a desiccant rotor, so it can both control the humidity and temperature of the air independently in one packaged unit. Operating Principles: Supply Air Stream Outside air is drawn into the unit using the supply fan. The warm, moist outside air first passes through filters and then the cooling coil where it is cooled. The air then goes through the desiccant wheel where the air is dehumidified and the temperature is raised. At last the air is delivered directly to the space or into an existing air handler. Exhaust Air Stream Exhaust air is used to provide energy recovery for the desiccant wheel and is drawn into the unit using the exhaust fan. The air filtered and then heated and humidified during the energy recovery process. The air is then heated while passing through the regeneration coil. The heated air removes the moisture that the desiccant wheel adsorbs from the process air stream. Applications: War Industry, Scientific Research, Electric Power Transportation Lithium Battery Industry, Biotechnology Pharmaceutical Industry Chemical, Daily Chemical Industry, Food Beverage Industry Safety Glazing Material Industry, Tyre and Rubber Industry Medical Instrument, Vegetables Frozen, Precise Instrument Wood Goods, Shipbuilding Painting Industry, Kinds of Storage Specifications: Main Parameters Model ZCB—6000 Total Process Airflow 6000m3/h Fresh Airflow 300 m3/h Recirculated Airflow 5700 m3/h Rotor Regeneration Airflow 2000m3/h Parameters of Output Air T=25℃ RH=20% Regeneration Power 42kw The Power of Regeneration Fan 1.5kw The Power of Blower 5.5kw The Power of Driving Motor 0.1kw Installed Power 49.1kw Cooling Load 232.6kw Power Supply 3P/380V/50HZ Competitive Advantage: Sweden Proflute silicon gel wheel A totally self contained unit PLC automatic control system, human-machine interface Aluminum alloy frame, anti-cold bridge Body modularization design, foam injected double wall casing Stainless steel drain pan and bottom boards Process and reactivation air flow sectors are insulated Electric or steam heating or convert type can be available All operation parameters can be on-line observed, ensuring operation reliability High temperature safety thermostat cutout Electrical interlocking of fan motors, heaters and rotor driving User Friendly Automatic Interface Control System: High Efficiency Silica Gel Wheel Industrial Dehumidifier With Cooling Coil 0 Production Workflow Chart: Rotary Wheel Industrial Desiccant Dehumidifier for Pharmaceutical Industrial 23.8kg / h We can make suitbale dehumidifying solution for you according to your requirements. If you are interest on our product, contact us now.

Product Description Raw material small chocolate machine Name chocolate molding machine production line Material 304 Stainess Steel Capacity 12-27moulds/min Type Fully Automatic Condition New Function Multifunctional Biscuit Type chocolate Condition NEW chocolate Machine Production Line Model MM-CL-002 chocolate making equipment/chocolate processing line 1. Directly Candy machine Manufacturer ,10 years experience focus on candy confectionery. 2. The whole line is used for production of all kinds of chocolate by automatic shaping, Full automaitc work program is applied throughout the flow of production, including mould heating, depositing,vibrating,cooling, demoulding and conveying. 3 It has the advantage of full automatic continuously working , high capacity, advanced technology 4. This machine services as advanced chocolate pour-forming equipment that intergrates mechanical control and electric control all in one. , 5. This machine can produce pure chocolate, chocolate with filling ,two-colour, chocolate and chocolate with granule mixed, The products enjoy attractive apperarance and smooth surface. Company Information: Luohe Ruikong Drive Technology Co., Ltd​ is a professional manufacturer and supplier in Henan province.We specialize in the research and development, manufacturing and sales of food machinery equipment. Our main products are including fruit and vegetable processing machinery, meat processing machinery, nut processing machinery, grain process machinery, packaging machinery,etc. We have professional technicians and foreign trade service teams with many years of experience in the mechanical industry. We not only have first-class quality, perfect service, but also have global advanced production equipment and technology. We welcome new and old customers from home and abroad to contact us for future business relationship to achieve mutual success! FAQ: Question 1:What are your advantages compared with your competitors? Answer: With rich industry experience and strict Product Quality Control systems, we provide: 1). Stable and reliable product at reasonable price 2). Good customer service: Fast response to any inquiry or question 3). On-time delivery. Question 2: Are you manufacturer? Answer: Yes, we are manufacturer with more than 10 years' experience. Question 3: What are your Price Terms? Answer: Price can be based on FOB, CFR, or CIF, etc. Question 4: What are your Payment Terms? Answer: Payment shall be made by T/T, L/C, or D/P, etc., it varies considerably according to the region that you are in. Question 5: What's your Minimum Order Quantity? Answer: Any order quantity is warmly welcomed. Question 6: Do you have English Manual for each machinery? Answer: Yes. The instruction manual,the test report and other Data Sheets related shall be provided by us. Our services 1. 24-hour communication service 2. Fast logistics will provide you a smooth delivery service 3. New design or product recommendation 4. Attend international exhibitions and have face-to-face negotiations with customers 5. If you want to come to China, we will send a formal invitation 6. The front desk service will help you book a good hotel New Condition Small Chocolate Machine Multifunctional Chocolate Production Line 0New Condition Small Chocolate Machine Multifunctional Chocolate Production Line 1

Product Description Kieselguhr / Loading And Unloading / Good Wear Resistance / Industrial Lobe Pump This pump with Radial Liners is installed in a brewery for loading and unloading of tank trucks with Kieselguhr. The flange connections have different nominal diameters at suction and discharge side, adapted to the requirements of the customer. Application data: Medium Kieselguhr Flow Rate 12 m³/h Viscosity / Pump Speed 270 rpm Temperature 30°C Pressure 4 - 6 bar pH value / Technical data: Casing GG25 Casing protection plate XAR500 Hardmetal Static O-rings NBR Shaft seal single-acting mechanical seal Rotors tri-lobe screw profile NBR Drive connection 3 kW Advantages of this Accuvon AP 100 - loading and unloading of tank trucks - Self-priming - Reversible - positive displacement pumps - good wear resistance - over pressure protection - Resistant to solids - Ease of maintenance Rotary Lobe Pumps are self-priming, valveless positive displacement pumps. The screw rotor enables pulsation free and gentle conveyance, the pump operation is reversible The crusher is an effective, widely applicable macerating unit based on the proven design of the Accuvon Rotary Lobe Pump: one principle, two bestsellers Waste Processes in the recycling industry demand reliable and robust pump units. The wide range of pump sizes, the option loaded modular design and the peripheral equipment enable Accuvon to supply a suitable Rotary Lobe Pump for your pump application. The Accuvon pumps allows the quick and convenient replacement of all fluid wetted parts without removal of pipes, drives or other components of the pump unit by your own staff. Quick - Uncomplicated - Inexpensive. The quick release cover allows simple access to the inner parts of the pump. The various, often strongly contaminated liquids in the recycling industry require individually customized selections of pumps: Accuvon offers various shaft seals designs and rotor materials with different coatings (Elastomer, PTFE or Urethane) or solid stainless steel rotors. Casing protection plates are supplied with various steel, plastic or ceramic qualities. For additional operation safety the Safety valve for over pressure protection can be added. Features of Accuvon Rotary Lobe Pumps: 1.Self-priming, Valve-less, Positive Displacement Pump 2. Easy Maintenance through Front Cover 3. Controllable Flow, Ratio up to 1 : 5 4. Capacity of up to 3200 m³/h 5.Pressures of up to 25 bar 6. Dry-running Capability 7.Reversibility, same pump output for both directions 8. Gentle, Low-Pulsation Pumping 9.For Viscous, Solid, Abrasive or Shea-sensitive Mediums 10. Low Parts Replacement Costs Components of a Accuvon Rotary Lobe Pump 1 Timing gear 2 Quench and control chamber 3 Casing in block design 4 Unwetted shaft 5 Axial and radial casing protection ( Optional materials from Hardox, Stainless Steel,Plastic or Ceramic ) 6 Shaft seal 7 Rotors 8 Quick-release cover Kieselguhr DN100 Two Lobe Rotary Pump , Antiwear Positive Displacement Lobe Pump 0