Other Industrial Equipment

Product Description Cold Extruded Plastic Granulator Machine For Pelletizing 3kw Advantages: 1,The equipment is suitable for processing the leftovers,rolls, bulk materials and other wastes of various materials such as PE,PP,PO,PVC, EVA,non-woven fabrics, etc. It can be used alone or synchronously with film blowing unit and film casting unit. 2,The granulation process is not heated and without water.The particle size can be controlled to be the same as that of raw materials,and the utilization rate is extremely high. 3,The equipment can be used immediately after startup without preheating.The operation is simple,and it only needs to put the raw material into the feeding port. Application: This machine has good stability, high efficiency and applicability.It is specially used for recycling and granulation of leftovers and waste materials of PE,PO,PVC,EVA,non-woven fabric and other plastics. Structure: The components of the equipment are: electrical parts,transmission parts,feeding parts,extrusion parts,pelleting parts and recycling parts. Features: 1.The machine does not need preheating during operation. It can be used immediately after startup.The operation is simple,it only needs to lead the raw material into the feed inlet. 2,The machine is space saving and low energy consumption.It soften the materials by simply rotating a single screw, extruding the die head,and cut out the same particles as the raw material. 3.The machine does not heat, neither change the molecular structure of the material during production.The usage rate is very high,and the output can reach to 60- 120Kg/h. 4.The machine is smoke free and dust-free, with extremely low noise and environmental protection. Model JXDW-125 Total Power 34KW Output ≈150kg/h Power Supply AC380V 50Hz TN-S Dimension 2200x1600x1100 Weight ≈1100kg Screw 125 Reducer 200 Pelletizing Motor 1.1W Extrusion Motor 30KW Inverter 30KW+1.5KW

PRODUCT DESCRIPTION Nitrogen closed loop spray dryer Inert gas atomization dryer Description: First of all, filling the nitrogen to be heated into the tower, the liquid materials to be dried are transported to the centrifugal atomizer, then they are rotatied in a high speed, and fially, they become the fine droplets, droplets in the drying tower fully heat exchange with nitrogen. The liquid parts have been instant evoperated, the solid parts become powder materials down to the bottom of the drying tower, and the last, the dried powder discharge from the bottom of the tower. Among them, evoparated organic solvent through the cyclone seperator, bag dedustor to remover the powder in the role of the blower, and then by the condenser, the dust removered saturated organic solvent gas into liquid discharge from the condenser. In case the liquid be carried out, there has addied a gas-liquid separator. Among them, as a drying medium for the inert gas being heated as a dry carrier in the system used to re-cycle. Explosion-proof closed cycle centrifugal spray drying system is working in a confined environment, drying medium is inert gas (like nitrogen), positive pressure operation in the drying tower. If the internal pressure decreased, the pressure transmitter can control the nitrogen amout entered into the drying tower automatically, to ensure system pressure balance.medium like nitrogen has a affact of bearying moisture, demoval moisture and cycle -transmission, the media can be used cycled. Closed Loop Spray Dryer Machine Inert Gas Atomization Dryer For Nitrogen Processing 0 Application: Chemical industry: Sodium fluoride (potassium), basic dyes and pigments, dye intermediates, compound fertilizers, formaldehyde silicic acid, catalysts, sulfuric acid agents, amino acids, white carbon black, etc. Plastic resin: AB, ABS emulsion, urea-formaldehyde resin, phenolic resin, dense rubber (urea) formaldehyde resin, polyethylene, polyvinyl chloride, etc. Food industry: Rich fat milk powder, grain, cocoa milk powder, milk substitute powder, egg white (yellow). Food and plant juice: Oats, chicken juice, coffee, instant tea, spices, meat, protein, soybean, peanut protein, hydrolysate, etc. carbohydrate: Corn syrup, corn starch, glucose, pectin, maltose, etc. ceramics: Alumina, ceramic tile materials, magnesium oxide, talcum powder. Closed Loop Spray Dryer Machine Inert Gas Atomization Dryer For Nitrogen Processing 1 Technical parameters Specifications XLP-5 XLP-10 XLP-25 XLP-50 XLP-100 XLP-150 Inlet air temperature 90-140°C,adjustable Exhaust air temperature 60-80°C, depending on the product to be dried, and URS Nominal water evap.capacity(Kg / h) 5 10 25 50 100 150 Heating method Steam Drying tower diameter (mm) 1300 1500 2000 2500 3200 3600 Overall dimensions (m) According to the configuration and URS Product yield 99-99.99%,varies with the product features and configuration Widely used in the pharmaceutical, chemical industry, foodstuff, spray dry powder process.ect. Product Features Uniform quality Complete control of moisture content, particle structure, particle size distribution, solubility, and wettability, and retention of natural aromas and flavors. Unbeatable performance /cost ratio Energy efficient components, continuous and rapid drying, ease of operation and process automation provide complete control over yield and costs. Versatility Customized plant design based on many years of experience in a wide range of applications is your assurance of complete compliance with individual requirements. Long service life Top-quality, reliable components, efficient and straightforward CIP and expert engineering increase service life and availability for maximum performance. Traceability Automated process control enables end-to-end traceability in compliance with current food standards and regulations. Our Campany Company introduction: Changzhou Melton Trading Co., Ltd was established in 2008. Our company is located in the birthplace of China's drying equipment industry - Zhenglu Industrial Park, Changzhou City, Jiangsu Province. It is a modern enterprise engaged in the R&D, production and sales of various drying equipment, sludge dryers, vacuum dryers, granulators, pulverizers, mixers, screening and dust removal and other equipment. In recent years, we have continuously increased investment in technical transformation, and manufactured a variety of low-energy, low-emission dryers to meet customers' environmental protection production needs. All kinds of drying equipment produced by our company are widely used in pharmaceutical, chemical, food, agricultural and sideline product processing, textile, electronics, light industrial products, fertilizer, feed and other fields. The products are all over the country and exported to Southeast Asia, Europe, America and other countries. The company adheres to the entrepreneurial philosophy of "technical innovation, quality-oriented", promotes the work style of "simple and rigorous, strives for perfection", advocates "enterprise integrity, considerate service", regards product quality as life, and respects customers from all over the world as friends. We warmly welcome people from all walks of life to come to cooperate, negotiate and seek common development!

DETAIL INFORMATION PRODUCT DESCRIPTION Detail Information Color: Yellow Or Sliver Or Customized Capacity: 0.3 - 40 Kg / H Voltage: 380V 50HZ Or Customized Weight: 400 - 1000 Kg Power: 0.75 - 15kw Plastic Processed: PLA ABS Warranty: 1 Year Name: Lab Mini 3D Printer Filament Extruder Machine High Light: 3d printer filament maker, 3d printer filament making machine Product Description Lab Mini 3D Printer Filament Extruder Machine Production Line Application: This extruder can be used for extruding ABS, PLA, PP, PE, PVC, PEEK, PC and other plastic material. This extruder is widely used in all kinds of laboratory and research institution as its advantages of small dimensiion, lower energy consumption and easy movement. We adopt ceramic heating rings in heating part, can heating temperature till 480℃, can be used in testing many different kinds plastic materials including some high temperature resistant materials. Main Features: 1. The output improving is 10%-20% better than the same type in the market. 2. The energy saving is 20%-40% better than the same type in the market. 3. The total cooling, just need to connect the inlet and outlet water, reduce customer's installation cost, beautiful appearance and easy maintenance. 4. Our products have passed environment protection. 5. Adopting advanced world famous brand components in pneumatic parts ,electric parts and operation parts. Item Equipment line SET 1 Vacuum feeder 1 2 Hopper dryer 1 3 Single screw extruder 1 4 Mold (1.75mm, 3mm) 1 5 Warm water tank and cooling water tank 1 6 Laser measuring diameter instrument 1 7 Haul off machine 1 8 Accumulator 1 9 Winding machine 1 10 Vacuum Sealing Machine 1

Automatic Mustard Oil Bottle Filling Machine Individually Actuated Edible Oil Filling Machine Introduce Automatic filling machine capacity can be customized to suit production speed. This bottling filling machine can be used for bottling juices, oils filling line, honey, food products, pharmacy syrups, foamy liquids filling line, free flowing low to medium viscous liquids. Automatic filling machines suitable to free-flowing liquids like oil, beverage, lotion . It can be applied to a wide range of industries including food and beverages, with high capacity, accuracy and stability, quick and easy changeover to save operation time, equipped with anti-dust and hygiene concern housing for option. Advantage 1. Built with anti-dust housing, hygiene concerning. 2. Filling nozzles can be customized for quantity and filling way to meet production requirement. 3. Advanced valves prevent liquid from dripping down. 4. Drip tray setting, surplus liquid backflow, no waste. 5. Adopted servo motor and gear pump, filling precisely and quick. 6. User-friendly system, simple-to-use. 7. No bottle, no fill sensor. 8. Color touch screen and PLC controlled. 9. Program recipe storage for simple and quick changeovers. 10. Precise sensor detected, no bottle, no fill. 11. Start, emergency stop and speed controller configuration. 12. Multiple filling and conveying speeds for accurate control of production. 13. Automatic pneumatic gates for bottle entry and exit. 14. Sturdy conveyor. 15. Conveyor guide rail can be adjusted to accommodate any size of bottles. 16. Built with mobility castors enable easy movement. 17. Heavy-duty steel, easy-to-maintain. 18. Compliance with GMP standard, made of SUS304 stainless steel and anodized aluminum. Main technical parameters No. Item Performance 01 Requested speed 50bpm 02 Filling volume 5000ml(could be customized based on requirements) 03 Number of filling heads 6 05 Accuracy Up to ±1% 06 Machine dimension(L*W*H) 2400mm*1350mm*2500mm 07 Power 5KW 08 Power supply AC 380V,50Hz;or AC 220V,50Hz (Customized) 09 Air operated source 0.4-0.6Mpa clean and stable compressed air 10 weight About2000kg Major technical components No. NAME BRAND 01 Frequency converter Schneider 02 Intermediate Relay Panasonic 03 PLC Siemens 04 Touch Screen Siemens 05 Breaker Schneider 06 Servo Panasonic 07 Photosensor SICK 08 Airpressure-Switch Airtac

Metal wall and roof profiles rolling forming machine for UK Here I will list some popular roofing and wall cladding profiles and rolling forming machine designs in UK and like England, Scotland and Northern Ireland. Single skin roof and wall systems consist of coated steel sheets rolled to six different profiles; they may be used to form roofs - down to 4°pitch (6if roof flights are required) - and walls. The system includes a comprehensive range of spacers, fixings, sealants, guttering, f lashings and roof flights. Metal roofing and wall profiles Here are some popular designs for your reference: Metal and roofing profile drawing Another popular design for roofing and wall cladding: Metal roofing and wall proflle drawing 2 The third popular wall cladding profiles: Metal roofing and wall profile 3 The forth AS35/1000 roof profile: Metal roofing and wall profile 4 The fifth AS13/3/990 roof profile: Metal roof and wall profile 4 If you need all the profiles with the filming, we supply the new material for for anti aging, keep warm and others. Usage usage Metal wall and roof profiles rolling forming machine for UK . For the profiles no matter for wall or for roofing, we can design the metal rolling forming machines either support the normal PPGI or the filmed coil. As to the profiles you can choose to use the single layer metal roofing sheet machine or double layer metal roofing sheet machine like followings. We have fully automatic or half automatic. Here are some machine pictures and videos for your reference. When you have the needs and clear ideas, we can design the machines for you and make the accurate quotations. Double layer machine: Metal roof and wall profile double layer machine Single layer metal roofing profile rolling machine.

PRODUCT DESCRIPTION Automatic Inputting And Output Hydraulic Die Cutting Machine Parameter: Maximum momentum 400KN Seissor speed 0.11m/s Stroke adjustment 0—110mm Range between the working tables 60—170mm Size of the upper pressing board 1250×600mm 1600×600mm Size of the pressing board 1250×610mm 1600×610mm Motor power 3KW Total weight 1950kg Application: Suitable for forming die cutter cutting all kinds of paper, paper money, uppers, soles, leather, plastic, cloth, leather bags, toys, hats, spongy floss pieces, floor materials, soft film and various needs with knife mold cutting out. Advantage: This machine adopts the computer control system, the touchscreen display screen, the operation is simple, quick and accurate. Double oil cylinder, four-column automatic balance connecting rod structure, ensure that each cutting position is the same. It can automatically control the feeding device with single side or double side, which can increase the production efficiency of the whole machine by two to three times. When the cutting plate is under pressure, the cutting is automatic, so that the upper and lower parts of the cutting board have no size error. Special setting structure, with cutting knife and cutting height, make the adjustment simple and accurate. The automatic lubrication system ensures the precision of the machine and the machine durability.

EVA LLDPE High Quality Flexible Vacuum Cleaner Plastic Pipe Extruder Machine EVA LLDPE Spiral Corrugated Pipe Characteristics: The pipe is mainly used for vacuum cleaner pipes and swimming pool suction pipes 1. High quality material, It is mainly EVA material, antistatic, inner smooth surface, low working noise, solid structure, strong tear resistance. 2. After strong stretching or folding, it can quickly rebound to the original shape. 3. High bending rate can be achieved. LLDPE EVA Plastic Pipe Extruder Machine Flexible EVA Extrusion Machine 0 Machinery introduction: The company specializes in the production of EVA corrugated pipe machines. The production line has absorbed Italian technology and gradually formed a characteristic extrusion production line after years of continuous improvement. The production line adopts Siemens PLC control molding, with high degree of automation and stable production. The production line mainly includes vacuum feeding machine, drying hopper, single-screw extruder, mold, stainless steel water tank, molding machine, Siemens control system, transfer roller, flying knife cutter, and stacker. LLDPE EVA Plastic Pipe Extruder Machine Flexible EVA Extrusion Machine 1

Large Capacity 10L Industrial Ultrasonic Cleaner For Carburetor / Pistons Cleaning Auto Parts Cleaning machine We are manufacturing and supplying of Automotive Ultrasonic Cleaners. We offer a wide range of ultrasonic cleaners. These are Single or Multistage Ultrasonic Cleaners, which are both manually operated & fully automated systems. Further, the machine is widely used and appreciated by our clients due to its professional dependability and user friendliness. As the temperature of the cleaning solutions is directly related to the cavitational effect of the ultrasonic energy the Ultrasonic cleaners are delivered with built-in electrical heating elements complete with thermostatic controls. In this way an optimum combination of cleaning product (solution), temperature and ultrasonic power can be reached. ULTRASONIC CLEANING Ultrasonic cleaning uses sound waves to create millions of small bubbles in a tank of cleaning solution. The parts to be cleaned are submerged in the solution and as the bubble are formed and “explode” they remove any dirt, grease, carbon etc. This method also works very well. The one disadvantage that I noticed with ultrasonic cleaning is that aluminum parts do not come out of the cleaning tank looking like new. They seem to have some discoloration to them even though they were clean. If you are going to paint the parts then this shouldn't matter. We are the manufacturers of custom built Ultrasonic Cleaning machines for degreasing and cleaning of auto parts for OEMs , work shops , job works and auto- restoration industry. We expertise in providing customized designed solution for auto parts cleaning. Ultrasonic cleaning is a water based cleaning solution where ultrasonic transducers are used to provide cavitation agigation insude the tank which has waer and suitable chemical to clean oil,dirt,debree,grease and other contaminants from various types of auto components. We expertise in all types of ancilary parts washing like brakepads, steering coloumns, crank shats, pistons, valves, gaskets, clutch pads, mirrors and many more. An ultrasonic injector cleaner and injector flow bench. The preferred method of cleaning injectors. Cycles the fuel injectors while the fuel injector tips are immersed in an ultrasonic bath, which uses an environmentally friendly cleaning fluid to clean the fuel injectors. The flow bench portion also allows a user to perform a flow test before and after cleaning, and it allows the user to observe the fuel injector spray pattern. This method requires that the fuel injectors be removed from the engine How do I get the best ultrasonic cleaning? There are many considerations important to ultrasonic cleaning. Optimising these variables will produce the best cleaning. The most important decisions to be made are choosing the proper cleaning solution, cleaning at the right temperature for the correct amount of time, and choosing the right size and type of ultrasonic cleaner. Is a special solution required for cleaning? Soils adhere to the parts... if they didn't, the soil would just fall off the parts! The purpose of the solution is to break the bonds between parts and their soils. Water alone has no cleaning properties. The primary purpose of the ultrasonic activity (cavitation) is to assist the solution in doing its job. An ultrasonic cleaning solution contains various ingredients designed to optimise the ultrasonic cleaning process. For example, increased cavitation levels result from reduced fluid surface tension. An ultrasonic solution will contain a good wetting agent or surfactant. Industrial Ultrasonic Parts Cleaner Using aqueous (water based) detergents, AGSONIC ultrasonic equipment effectively removes oil, swarf and other contaminants from machine parts, tooling, jigs, tubes and many others. This maximises throughput, increasing productivity and eliminating needs for re-cleans, which makes it one of the most effective and environmentally friendly ways for cleaning these parts and components. applications including the following and more: Automotive Maintenance, Rebuilding and Restoration Flood, Fire and Storm Damage Cleanup Metallic and Ceramic Filter Cleaning Printing Equipment Maintenance General Maintenance Cleaning in Shop Environments Medical Precision Cleaning 10l Ultrasonic cleaner Specifications: Model TB-200 Ultrasonic Frequency 40,000 Hz Material SUS304 Tank Capacity 10.8L Ultrasonic Power 200 W Heating power 450W strong power, quick heating Timer 1-30min adjustable Heater 0-80C adjustable Unit Size 325 x 265 x 280 mm ( L x W x H ) Tank Size 300 x 240 x 150 mm ( L x W x H ) Package Size 435 x 360 x 350 mm ( L x W x H ) N.W. 7.4 kg G.W. 8.5 kg Power Supply AC 100 ~ 120V, 50 / 60Hz AC 220 ~ 240V, 50 / 60 Hz Features of the machine: •Low maintainence machine •Heavy duty cleaning systems •Chemical friendly- SS Rust proof body •Industrial guage farication, build to last •One year warrenty on any manufacturing defect •Completely customized to suit the cleaning requirement •Less human interfearance and less scope of error •Accurate and uniform cleaning everytime Digital Series High Performance Ultrasonic Cleaning system offers a new dimension to your cleaning needs. The single chamber device is used to clean surgical instruments and other hardware with sonic energy in a water detergent solution. All units are fabricated from solid stainless steel incorporating sweep frequency circuitry for a more uniform cleaning action. Custom sized tanks are also available . Applications include Surgical instruments, Laboratory items, Golf Club cleaning, Light fittings & automotive parts.

Steel Profile IBR&Corrugated Double Layer Roofing Panel Cold Roll Forming Machine Draft Specifications Voltage 380V 50Hz 3Phase or as your requirement Thickness 0.3-0.8mm or customized Material Galvanized steel ,PPGI Speed About 0-15 m/min Drive system By chain Cutting system Hydraulic cutting Machine Component Name NO. Unit 1.Decoiler 1 set 2.Forming machine 1 set 3.Cutting device 1 set 4.PLC control box 1 set 5.Hydraulic pump station 1 set 6.Production support table 1 set Specifications The total length of the equipment Length 6200mm width 1300mm height 1200mm Equipment weight 3 tons The motor power Motor 4Kw pump station 4Kw working voltage 380V or customized Production speed 10--18 m/min The transmission way 1 inch chain drive rack Large frame: 350H section steel shaft 1064:11 row axis 1100:13 row axis diameter 70 mm solid shaft The thickness of the plate 14 mm Set of Galvanized pipe finishing, electrostatic spraying Wheel material 45# steel hard chrome plating The molding part Divided into precision wheel rotation forming, forming effect is good, reduce the friction between wheels and raw materials, debugging convenient, fast. Numerical control system Easy control king, letter letter press button screen, counter, shear Iron plate welding frame, hydraulic cylinder automatic shear, hydraulic cylinder automatic pressure In the thickness of the plate 0.3 mm - 0.8 mm Into the plate width 1250 mm accessories Two sets of feeding rack, vulnerable parts Warranty period 12 months Uncoiler Loading capacity: 5T Inner diameter: 470-530mm Steel coil width :914, 1000, 1220, 1250 mm.According to your actual drawing. Working speed: 0-15m/min, adjustable Feeding table It is used to control the width and position of the steel sheet. The sheet is guided into the machine with correct position ,to make sure the panel is neat and parallel Control cabinet Suitable power : 380V, 50Hz, 3 phase. Or according to your need. Feature: The whole process is automatically controlled by the computer. In this way, you can ensure the accuracy and easy work

Product Description F-100 BFS Plastic Bottle Conjoined Labeling Machine The process Bottle feeding or manual feeding on the line → whole row to the labeling machine conveyor line → third-phase online printing of labels → labeling → Missed and missed online detection and removal → Next process Technical Specification No. Name Parameter 1 Speed 0～100 board/min 2 Precision ±1mm 3 Within the scope of the container Various small specifications conjoined plastic bottles 4 Label volume size Max Outside DiameterΦ400mm, Minimal lumen diameter Φ76mm 5 Overall dimensions (L)2900*(W)948*(H)2048 6 Weight 300Kg 7 Total power 2.5kw The non-drying label parameters (for reference) Label pitch: 2-4 mm ± 0.2 mm Below on the label and the bottom paper spacing below: 2 mm Bottom paper: need not less than 62 grams of white gration bottom paper, paper density and has very good internal strength and light transmittance, solid and not easily torn. Die cutting performance is wonderful. Basic gram: greater than 62g/㎡ thickness: greater than 55 microns Tensile strength: machine direction: 16kg/25mm Tear resistance: machine direction: 25g/sheet Through the brightness: 52% Device configuration schedule NO. Name Model or specification Brand Quantity 1 Programmable controller SIEMENS(S7-200) Siemens 1 2 Power supply SS-100-24(DC24V/100W) Meanwell (Taiwan) 1 3 Air switch C65N-C10N C16A/C10A Schneider (France) 2 4 Relay MY2N-D2 OMRON(Japan) 5 Out-of-standard servo motor SGMJV-08ADA61 YASKAWA 1 6 Server Driver SGMJV-08ADA YASKAWA 1 7 Conveyor reducer NMRV040-1:30 MOTOWARIO 1 8 Standard buffer motor and reducer 4RK25GN-CT-4GN9K TWT 1 9 Supply standard buffer photoelectric HP100-A1 YAMATAKE 1 10 Label stock photoelectric HP100-A1 YAMATAKE 1 11 Label detection photoelectric WF2-40B410 SICK 1 12 Work object detection FS-V11 KEYENCE 1 13 CCDCCD detection system BOT-DG-DA-03M-03 DESAL 1 14 Computer host + display DELL DELL 1 15 The electromagnetic valve 411A-D0A-DM-DDAA-1BA MAC 1 16 Bearing NSK NSK 17 Conveying chain plate 820-K325 Uni 1 18 Inverter FC51 Danfoss 1 19 Cab Cab printer Cab Germany 1

Structural features: ◆ Adopting the world's leading transmission control system, only need to input paper size system auto-tuning. ◆ Computerized high-speed fitting, up to 12,000 pieces per hour. ◆ Chuanliu-type air supply head, with four sets of forward nozzles and four sets of suction nozzles. ◆ Feida Block adopts low stack cardboard, which can fit the paper to the pallet, and can install track-assisted pre-stacker ◆ Use multiple sets of electric eyes to know the advance position of the bottom line, and make the servo motor on both sides of the face paper to independently rotate to compensate the upper and lower paper alignment, which is accurate and smooth. ◆ Full-function electronic control system, using human-machine interface and PLC program model display, can automatically detect operating conditions and work records. ◆ Automatic glue replenishment system can automatically compensate for lost glue and cooperate with glue recycling. Parameters: Model ZGFM1700 Max size 1700*15700 Min size 360*380 Paper 150-800g Bottom paper ≤10mm ABCDEF corrugated board Max speed 12000pcs/h Power 15kw Accuracy ±1mm 1. Product description 1.1 Structure: A. Upper Paper Feeder: It can send stacks of 150-800gsm paper from above. B. Bottom feed: It can send 0.5~1Omm paperboard from below. C. Gluing mechanism: The glued water can be applied to the fed paper. D. Regulatory organization - Fits the two papers according to the set tolerances. E. Pressurizing Conveyor... Presses the attached paper and conveys it to the delivery section 1.2 function: The paper can be laminated with paperboard to increase the strength and thickness of the material or special effects. After the die-cutting, it can be used for packaging boxes, billboards and other purposes. 1.3 Principles: The top paper is sent out by the upper paper feeder and sent to the start detector of the positioning mechanism for detection. Then the bottom paper is sent out; after the bottom paper is coated with glue on the glue wheel, the top paper and the bottom paper are respectively conveyed to the paper Synchronous detectors on both sides, after the detection, the controller calculates the error value of the paper and the bottom paper, and the servo compensation device on both sides of the paper compensates the paper to a predetermined position for splicing, and then pressurizes the conveying. The machine presses the paper and conveys it to the delivery machine to collect the finished product. Paste paper --- 180 ~ 800g/m thin paper, cardboard. Bottom paper---0.5~10m/m paperboard, single-sided cardboard, multi-layer corrugated paper, pearl board, honeycomb board, styrofoam board. Glue - resin, etc., PH value between 6 ~ 8, can be applied to the glue.

PRODUCT DESCRIPTION Plane Rapid Gate Electric Hydraulic Cylinder , Simple Hydraulic Cylinder Hydraulic hoist Plane rapid gate hydraulic hoist Key Specifications/Special FeaturesKey Specifications/Special Features Application industry water conservancy, mechanical/marine/mining equipment, oil industry, vehicles, energy and port facilities Stroke length 50 to 16,000mm Tube inner diameter 80 to 1,050mm Piston rod diameter 45 to 600mm plate Ni/Cr/ceramic Wor , king pressure 70 to 700 bars bearing LONGXI(china)or SKF Seal type common stand or in accordance with client's requirement (we usually use Parker from USA or MERKER from Germany) valves parker/rexroth/atos/ , hydcom Certification DNV, ABS, Lloyds, BV, SGS, GL, and CCS Material carbon, alloy, stainless steel Detail manufacturing drawings to be submitted to buyer for approval before manufacture is commenced QPKY series hydraulic hoist mainly apply to opening and closing of the common plane rapid gate in hydropower project, the basic parameters and the shape of installation size is exactly the same as QPKY Ⅱseries, except the hydraulic control valve using speed control one. QPKY Series hydraulic hoist, Plane rapid gate hydraulic hoist Hydraulic cylinder is the hydraulic energy into mechanical energy, reciprocating motion to do (or swing movement) of the hydraulic actuators. It is simple, reliable. Use it to achieve reciprocating movement can be removed from deceleration devices, and no transmission gap, smooth motion, so in a variety of machines are widely used in hydraulic systems. Hydraulic cylinder output force and the effective area of the piston is proportional to the pressure difference on both sides; hydraulic cylinder is basically a cylinder and cylinder head, piston and piston rod, seals, cushioning device and the exhaust composition. Buffer device and the exhaust depending on the specific application of the occasion, other devices are indispensable. Cylinder and cylinder of the advantages and disadvantages: 1. As the pneumatic system uses pressure is generally in the range of 0.2-1.0Mpa, so the cylinder is the driving force can not do high-power components. Hydraulic cylinders can be done relatively large power device, use the hydraulic system; 2. From the media about the air can be unlimited, no cost and supply difficulties, the gas will be used directly into the atmosphere, convenient, no pollution, hydraulic oil is the opposite; 3. The air viscosity is small, the resistance to less than the hydraulic oil; 4. But the air is much larger than the compression rate of hydraulic oil, so it's working smoothly and to respond to far backward in this regard. Hydraulic cylinder hydraulic system is the most important components of implementation, it can convert mechanical energy of hydraulic and matched with a variety of transmission to complete all of the mechanical movement. Hydraulic cylinder has a simple structure, the output force, stable and reliable performance and easy maintenance, wide range of applications and so on.

Model Number 1.5G,3G,6G,9G Applicable Industries Farms, Food & Beverage Shops, Building Material Shops, Garment Shops, Food & Beverage Factory, Machinery Repair Shops, Manufacturing Plant, Restaurant, Food Shop, Advertising Company, Hotels, Printing Shops, Retail, Other, Home Use, Energy & Mining, Construction works Marketing Type New Product 2020 Machinery Test Report Provided Video outgoing-inspection Provided Warranty of core components 1 Year Core Components Gear, Other Key Selling Points High Productivity Weight 0.2KG Application Poultry Farm Chicken Feeding Usage Feeding Poultry Product name Automatic Poultry Farm Equipments Chicken Feeder Material PP Plastic Color Red White Advantage Long Time Used User Chicken Broiler Layer Breeder Keywords Chicken Poultry Feeder feeders and drinkers for chickens making machine poultry chicken feeder machine Shipping: By courier, By sea, By Air (DHL, UPS, FedEx, TNT...) DELIVERY TIME: By courier, usually, 2 - 5 Days to arrive. By air to the company, usually, 5 - 15 Days to arrive. By to seaport, usually, 7 - 30 Days to arrive. FAQ Q: Do you offer samples? A: Yes, all products are available provided as samples. Q: Can you help customer to design their own products? A: Yes, Not only customize works, Zhengyuan also help you create special design products according to your needs. Q: Do you accept sample order or small order? A: Yes, we supply sample order for customer as well. Q: What is the process of ordering and cooperating with Zhengyuan? A: Search for the products you prefer •Solve problems and confirm the products •Quote the selected products Types of payment •Delivery method •After-sale service Q: Are all the products approved international certification? A: Most of our products have approved CE certification. Moreover, all products have been tested and full inspection before shipment Q: Can we have our logo on the product? A: Absolutely! As long as ordered quantity meets and provide us with your drawing, we are able to place your logo on the product. Q: How long will we receive the goods? A: The delivery time is normally 5-7 days after receiving down payment. Q: Is there any product guarantee? A: We have full after-sales-service. And if you found any defective product, excluding improper use, we would offer replacement services.

Introduction: ZYD transformer oil filtration process serves to improve the properties of insulating oil. It eliminates the acid nature, over moisture, traces of water, dissolved gases, and particulate matter from the insulating oil effectively and rapidly. The bottom line of this purification process is to enhance the performance level of transformers, circuit breakers, mutual inductors, cables, and capacitors. All these equipment and machinery use an insulating system. Features: Expectations on an effective oil plant for treatment of insulating oil. Suitable for oil treatment, vacuum oil injection and cyclic hot oil drying in the installation and maintenance of large capacity transformers. Easy and failsafe operation. On-line measuring and recording of process parameters. Used in the electric power system (110kV~500KV). Features include low noise, high-strength working vacuum, and high efficiency filtering process Double-stage vacuum system, strong power of vacuum evacuating, ultimate vacuum value ≤5Pa The unit can be used for the transformer vacuum oiling and for various wet electrical equipment vacuum drying. Flexibility in application(flow frequency conversion, suitable for transformers of different sizes) Technical Data Parameters Unit ZYD-30 ZYD-50 ZYD-100 ZYD-150 ZYD-200 ZYD-250 ZYD-300 Flow rate L/min 30 50 100 150 200 250 300 Working vacuum MPa 0.08 ～ 0.099 Working Pressure MPa ≤0.3 Temperature Range ℃ 20 ～ 80 Power Three Phase 50HZ380V(as per the customer's requirements) Working Noise dB（A） 75 75 75 80 80 80 80 Heating Power kW 30 30 45 60 75 90 120 Total Power kW 35.5 37.5 52.5 71.4 86.5 102.5 135 Inlet/Outlet mm φ25 φ32 φ42 φ50 φ50 φ60 φ60 Weight kg 600 800 1050 1400 1800 2000 2200 Overall Length mm 1050 1100 1200 1450 1600 1800 1900 Width mm 750 800 950 950 1100 1200 1200 Height mm 1350 1400 1500 1650 1800 1900 1900 Aftre treatment Moisture PPM ≤3 Gas content % ≤0.01 Impurity size μ ≤1 (no free carbon) Breakdown voltage kV ≥75 IFT dynes/cm ≥40 Acid value mgKOH/g ≤0.03 Dielectric loss factors tgδ(90°C) ≤0.001 ASSEN warrants the plant supplied under this specification against defects in material and workmanship under normal use and service for a period of twenty- six (26) months from date of shipment or twenty-four (24) months after the start-up of the system. ASSEN's obligation under this warranty is limited to repairing or furnishing, a similar part to replace any part, which was proven to be defective within the warranty period. 1. We customize the machine as your requirements. 2. We have more than 20 years export experience. 3. We offer our customers high quality products at competitive price. 4. We offer our customers excellent after-sales service. 5. We are not satisfied until our customers are satisfied. Please contact:Assen Email:sales(at)assenpe(.)com or assenoilpurifier(at)gmail(.)com Tel/Fax:+86-238 , 8703683 Whatsapp:+86-15223801122 https://www , .assenpe.com https://www.oilrecondiiton.com

Minimum Order: 1 bags