Fiber Optic Equipment

16 Port Outdoor Fiber Distribution Box Black Outdoor optical distribution Frame Description: Fiber optic terminal box is available for the distribution and terminal connection for various kinds of optical fiber system, especially suitable for mini-network terminal distribution, in which the optical cables, patch cores or pigtails are connected. Features: The box is made of ABS, and lifetime is more than 20 years. It also can be used under -30°c. Bi-layer structure design. The upper layer is for optical splitter, the other layer is for fiber splicing. Easy to operate. Usually installed as wall mounted in the building or at the green belt. It can accommodate 16 pcs SC Simplex or LC Duplex dapters. It can be designed to client requirements. It meets YD/T988-2007 standards. Application: FTTH access network CATV Networks Telecommunication Networks Data communications Networks Operation conditions: Temperatures:-40℃ — 60℃ Humidity:93% at 40℃ Air Pressure:62kPa – 101kPa

12VDC 10G Base-T to 10G Jumbo Frame SFP+ RJ45 to Fiber Ethernet Media Converter Model: LNK-10G-MC Series Overview E-link 10G Base-T to 10G Base-R Media Converter supports two types media for network connection such as 10GBase-T and 10GBase-FX. The bridge media converter is designed with a 10Gbase Ethernet PHY chip that connects two types segments operation smoothly. This converter can be used as standalone unit or as slide-in module to the 19" converter rack Chassis for use at a central wiring closet. Features Support Jumbo Frame Transparent Transport and very low delay Support DMI function for SFP+ fiber module Support Loopback test function Support hot plugging Full State Led display Easy installation Provide reliable long-distance connection Fast connection with multi-function Small portable size case Plug and play Application Connection between fiber to copper 10Gbps Ethernet equipment function as fiber-to- copper media converter for long distance transmission up to 120km Extend the network distance between two 10 Gigabit Fiber Switches across a fiber link up to 80km in length Convert your 10G SFP+ Direct Attach to multimode or single mode fiber. Technical Indexes Standards 1000Base-T, 2.5GBase-T, 5Gbase-T, 10Gbase-T 1000Base-X, 2500Base-X, 5GBase-R , 10GBase-R Media Supported 1000Base-T: Cat5 UTP/STP. MAX 100m; 2.5GBase-T: Cat5e UTP/STP. MAX 50m; 5GBase-T: Cat5e UTP/STP. MAX 50m; 10G Base-T: Cat6a UTP/STP. MAX 50m; Port Type RJ45, SFP Slot Work Mode 1000Base-T to 1000Base-X 2.5GBase-T to 2500Base-X 5Gbase-T to 5GBase-R 10Gbase-T to 10GBase-R Power Supply 12V DC Power consumption MAX 5W Operation Temperature 0℃ to 55℃ Relative Humidity 5% to 80% (non-condensation) Ordering Information Model Description LNK-MC10G-SFP+ 10G Base-T to 10G Base-R Media Converter, SFP+ Ports, not including SFP+ Modules

TX-2.5G/RX-1.25G GPON Transceiver Class B+ (SMF, 1490nm-TX/1310nm-RX, 20km, SC ) Description The GIGAOPTO's GTS-SGT21-20DCB is a high performance transceiver module for single fiber communications using a 1490nm continuous-mode transmitter and a 1310nm burst-mode receiver. It is designed to meet ITU G.984.2 Class B+ requirements for optical line terminal (OLT) applications. The 1490nm DFB LD transmitter has automatic power control (APC) function and temperature compensation circuitry to ensure stable optical power and extinction ratio over all operating temperature range. The transmitter meets Class 1 eye safety per IEC60825 and CDRH standards.The receiver has a hermetically packaged APD-TIA (trans-impedance amplifier) pre-amplifier and a limiting amplifier with LVPECL compatible differential outputs. It features a Burst Packet Detect (SD) output which is LVTTL compatible. The SD output will come high after receiving the burst packet. The module provides digital diagnostic information of its operating conditions and status, including transmitting power, laser bias current, module temperature, and supply voltage. Calibration and alarm/warning threshold data are written and stored in the internal memory (EEPROM). SFP transceiver module has done sampling test under most famous brands of routers, switches, servers. The hot swappable GPON SFP transceiver is ideal for Internet Service Provider (ISP) Gigabit Passive Optical Network (GPON) communication links, other optical links. Specification Form Factor GPON SFP Power Supply Voltage 3.3V Connector/Polish SC/UPC Maxim Distance 20km DDM Supported Media SMF Warranty 3 Years Temperature Commercial /Industrial TX Data Rate 2.488Gbps RX Data Rate 1.244Gbps TX Wavelength 1490nm RX Wavelength 1310nm Power Consumption <1.5W Total Current 450mA Transmitter Type DFB Receiver Type APD TX Optical Power +1.5~+5.0dBm RX Sensitivity < -28.0dBm Extinction Ratio >8.2dB Receiver Overload >-8dBm Protocols SFF-8472, ITUT-984.2 Features Single fiber bi-directional data links asymmetric TX 2488Mbps/RX1244Mbps application 1490nm continuous-mode DFB laser transmitter and 1310nm burst-mode APD-TIA receiver Small Form Factor Pluggable package with SC/UPC Connector 0 to 70°C operating temperature Single 3.3V power supply Digital diagnostic monitoring interface Digital burst RSSI function to monitor the input optical power level LVPECL compatible data input/output interface LVTTL transmitter disable control LVTTL transmitter laser fault alarm Fast LVTTL receiver Signal Detect (SD) indication response Low EMI and excellent ESD protection Class I laser safety standard IEC-60825 compliant RoHS6 Compliance Application Gigabit-capable Passive Optical Networks (GPON) Standards Complies with SFP Multi-Source Agreement (MSA) SFF-8074i Complies with ITU-T G.984.2 Amendment 1 Complies with FCC 47 CFR Part 15, Class B Complies with FDA 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007 Complies with SFF-8472 Compatible with TR-NWT-000870 4.1 ESD sensitivity classification Class2. Compatible with Telcordia GR-468-CORE Ordering information - Gigaopto’s GPON OLT SFP Series(DFB+APD SC Simplex) P/N Date Rate (Gb/s) Wavelength (nm) Class Tx Power Rx Sensitivity Temperature GTS-SGT21-20DCB TX-2.488/RX-1.244 TX-1490nm/RX-1310nm B+ +1.5~+5.0dBm < -28.0dBm Com GTS-SGT21-20DIB TX-2.488/RX-1.244 TX-1490nm/RX-1310nm B+ +1.5~+5.0dBm < -28.0dBm Ind. GTS-SGT21-20DCC TX-2.488/RX-1.244 TX-1490nm/RX-1310nm C+ +3.0~+7.0dBm < -30.0dBm Com GTS-SGT21-20DIC TX-2.488/RX-1.244 TX-1490nm/RX-1310nm C+ +3.0~+7.0dBm < -30.0dBm Ind. GTS-SGT21-20DCD TX-2.488/RX-1.244 TX-1490nm/RX-1310nm C++ +4.5~+10.0dBm < -31.0dBm Com GTS-SGT21-20DID TX-2.488/RX-1.244 TX-1490nm/RX-1310nm C++ +4.5~+10.0dBm < -31.0dBm Ind. GTS-SGT21-20DCE TX-2.488/RX-1.244 TX-1490nm/RX-1310nm C+++ / D +6.0~+10.0dBm < -32.0dBm Com GTS-SGT21-20DIE TX-2.488/RX-1.244 TX-1490nm/RX-1310nm C+++ / D +6.0~+10.0dBm < -32.0dBm Ind. Note OEM/ODM Supported, Please Feel Free To Contact Us! Compatibility All of GIGAOPTO's GTS-SGT21-20DCB SFP optical transceiver modules are open sourced, can be coded to be fully compatible with worldwide popular brands' devices, e.g. HUAWEI MA5603T, HUAWEI MA5608T, HUAWEI MA5680T, HUAWEI MA5800T, ZTE ZXA10 C300, ZTE ZXA10 C320, ZTE C600, Alcatel-Lucent 7360, Nokia 7360, C- DATA, VSOL, BDCOM. Please refer to the following table for detailed compatibility, please feel free to contact us. Corresponding Compatible Brand/Part Number Brand Part Number Brand Part Number Gigaopto GTS-SGT21-20DCB Alcatel-Lucent 3FE53441AA 01 HuaWei GPON-OLT-CLASS B+ Nokia 3FE53441ACAA ZTE GPON-OLT-Class B+ Calix 100-01782 ZTE 33030100152 Dasan MXK-GPON-SFP-B+-RSSI Ubiquiti UF-GP-B+ Cisco SFP-GPON-B BDCOM OLT-GSFP-B+ Calix 100-01836 Broadex D24364-SSCB SuperXon SOGP4321-PSGB WTD RTXM167-522

Product Description C Band 75/100GHz 400G Coherent Module QSFP-DD ZR 80~120KM for DCI Applications This product is a coherent module, compliant with the OIF 400ZR MSA and QSFP-DD MSA standards, is designed for DCI applications. The digital diagnostics function is available via an I2C interface, as specified by the QSFP-DD MSA. The product is a C-band 75G/100 GHz grid coherent optical module that combines coherent DSP ASIC functionality with best in class ultra-narrow line-width tunable lasers, high speed modulators and high responsively coherent receivers to deliver high performance at 400G 16QAM modulation formats (at 60G baud rate). C Band 75/100GHz 400G Coherent Module QSFP-DD ZR 80~120KM for DCI Applications 0 Features QSFP-DD MSA compliant Compliant with OIF 400ZR, version 01.0, March 10, 2020 Digital diagnostic monitoring support Hot pluggable by 76-pin electrical interface Maximum power consumption 16.5 W 400G 16QAM modulation Compact size (18.4 mm x 93.4 mm x 8.5 mm) LC duplex connector 400GBASE-R, 425 Gbps bit rate 400G-AUI-8 C2M; 8 x CEI-56G-VSR PAM-4 electrical interface Operating case temperature: 0°C to 70°C Single 3.3 V power supply RoHS 2 compliant Optical Characteristics Parameter Min Typ Max Unit Conditions Transmitter Transmitter frequency range 191.3 193.7 196.1 THz TU-T grid. Frequency range over which the specifications hold unless noted otherwise. The frequency is fixed at 193.7 THz for unamplified link applications. Transmitter laser frequency stability -1.8 1.8 GHz Offset from channel frequency set point. The receiver LO has the same frequency accuracy. Transmitter output power -10 -6 dBm Measured at optical connector. Transmitter output power with TX disabled -20 dBm Max Output power with TX_DIS asserted Transmitter output power during wavelength switching -20 dBm Transmitter reflectance -20 dBm Transmitter polarization dependent power Mean I-Q amplitude imbalance 1 dB Transmitter polarization dependent power 1.5 dB Power difference between X and Y polarization Receiver Frequency offset between RX and LO -3.6 3.6 GHz Acquisition Range Input power range -12 0 dBm Input sensitivity (amplified link application) -12 dBm Input sensitivity (unamplified link application) -20 dBm For unamplified link applications, the minimum input power is –20 dBm @receiver OSNR tolerance ≥ 34 dB. OSNR tolerance (amplified link application) 26 dB/0.1nm The OSNR tolerance is referenced to an optical bandwidth of 0.1 nm @193.7 THz or 12.5 GHz. OSNR tolerance (unamplified link application) 34 dB/0.1nm The OSNR tolerance cannot be less than 34 dB for unamplified link applications. Optical return loss 20 dB Optical reflectance at connector input CD Tolerance 2400 ps/nm Tolerance to chromatic dispersion Optical path power penalty 0.5 dB OSNR penalty tolerance due to –35 dB interferometric crosstalk and 2400 ps/nm chromatic dispersion. PMD tolerance 10 ps Tolerance to PMD with ≤ 0.5 dB penalty to OSNR sensitivity. 10 ps of PMD corresponds to max 30 ps of DGD and max 500 ps2 of SOPMD PDL tolerance (amplified link application) 3.5 dB Tolerance to PDL with < 1.3 dB penalty to OSNR sensitivity When change in PSP is ≤ 1 rad/ms. PDL tolerance (unamplified link application) 2.5 dB The PDL tolerance is 2.5 dB in unamplified link application when the reciever OSNR sensitivity penalty is 0.8 dB. Tolerance to change in SOP 50 krad/s Tolerance to change in SOP with ≤ 0.5 dB penalty to OSNR sensitivity. Measurement relative to reference with 10 ps PMD and 2.5 dB PDL and SOP of < 1 rad/ms under the same conditions. Optical input power transient tolerance ±2 dB Tolerance to change in input power with ≤ 0.5 dB penalty to OSNR sensitivity. Received power is within –12 dBm to 0 dBm. Rise/fall times of power change defined by 20%–80% of 50 µs or slower.

PRODUCT DESCRIPTION PLC fiber optic Splitter 1x8 blockless mini module with fan-out kits LC/APC, SC/APC 1x8 Fiber optic PLC Splitter is also called 1*8 fiber optical plc splitter, optic fiber plc splitter, optical fiber plc splitter, plc fiber optic splitter or plc optical fiber splitter. We can produce the fiber optical splitter with connector or without connector! Fiber optic PLC Splitter Description: PLC splitter are based on Planar Waveguide Technology. They provide a cost effentive and space saving networking solution. They are key components in FTTx networks and are responsible to distribute the signal from central office to numbers of promises. They have very wide range of operatng wavelength from 1260nm to 1620nm. With it’s compact size, these splitters can be utilized in in-gruond and earial pedestals as well as rack mount system. It is used for small spaces can be easily placed in a formal joint boxes and splice closure, in order to facilitate welding, does not need specially designed for spave reserved. Our PLC splitter family features either ribbon or individual fiber output, We provides whole series of 1xN and 2xN splitter products that are tailored for specific applications. All splitters provide guaranteed optical performanve and high reliability that meet GR-1209-CORE and GR-1221-CORE requirement. Fiber optic PLC Splitter Options: - 1xN: 1x2, 1x4, 1x8, 1x16, 1x32, 1x64 splits. - 2xN: 2x2, 2x4, 2x8, 2x16, 2x32, 2x64 splits. - Un-connectorized. - Fiber jacketing outside boxes 2mm and up to 3mm. - ABS box type or inside metal box/module cassette type. - SC/UPC, SC/APC, LC/UPC, LC/APC, FC/UPC, FC/APC, ST/UPC, ect connector options. - Custom connector configurations and combinations. Fiber optic PLC Splitter Applications: - Fiber to The Point (FTTX). - Fiber to The Home (FTTH). - Passive Optical Networks (PON). - Gigabit Passive Optical Networks (GPON). - Local Area Networks (LAN). - Cable Television (CATV). - Test Equipment. Fiber optic PLC Splitter Features: - Low insertion loss. - Low Polarization Dependent Loss. - Excellent Environmental Stability. - Excellent Mechanical Stability. - Telcordia GR-1221 and GR-1209.

100Base FX Multi Mode Rugged SFP GLC-FE-100FX-RGD Cisco Transceiver Module GLC-FE-100FX-RGD Overview The GLC-FE-100FX-RGD is a third-party compatible SFP for Cisco. This 100BASE module will reach 2km and uses a wavelength of 1310nm. All GLC-FE-100FX-RGD are in-system tested in real Cisco routers and switches. This Cisco compliant GLC-FE-100FX-RGD is a 100BASE-FX SFP 1310nm 2km transceiver module. The GLC-FE-100FX-RGD transceiver module provides a low cost high-performance connection. The GLC-FE-100FX-RGD is 100% compatible with all Cisco series switches and modules which support SFP transceivers. Features & Specifications Form Factor: SFP Device Type: Transceiver module Interface (Bus) Type: Plug-in module Connectivity Technology: Wired Application: 100BASE-FX Data Transfer Rate: 100Mbps Wavelength: 1310nm Max Distance: 2km Fiber Type: SMF/MMF Connector: Duplex LC DDM: Without DDM Operating Temperature: 0~70 °C Compliant with MSA SFP Specification GLC-FE-100FX-RGD Specifications Product Name GLC-FE-100FX-RGD Media Fiber Wavelength 1310nm Data Rage OC48 Mode LC Connector Type SM Distance 2km 1310nm 2KM Cisco Transceiver Module 100Base FX Multi Mode Rugged SFP GLC-FE- 100FX-RGD 0 FAQ 1. Where do your products come from? All of our products are from Cisco/Huawei distribution , Cisco/Huawei partner directly. We are Cisco partner at local, with cisco verified certification. 2. If all equioments I can buy service from local cisco ? For all equipments you can buy service from local, because our goods are smart net free, all with clean serial number. 3. How to ship the goods? Lonrise work with DHL,FEDEX,UPS and TNT. Your order will be dispatched by express delivery door to door. 4. What’s your payment term? We always accept 10% advance payment. For long term cooperation, we can consider to apply credit accordingly. Related products SFP-10G-SR SFP-10G-LRM SFP-H10GB-CU3M SFP-10G-ER SFP-10G-ER QSFP-H40G-CU3M QSFP-H40G-CU0-5M QSFP-H40G-CU5M QSFP- 4SFP10G-CU1M

TX-2.5G/RX-1.25G GPON Transceiver Class B+ (SMF, 1490nm-TX/1310nm-RX, 20km, SC ) Description The GIGAOPTO's GTS-SGT21-20DCB is a high performance transceiver module for single fiber communications using a 1490nm continuous-mode transmitter and a 1310nm burst-mode receiver. It is designed to meet ITU G.984.2 Class B+ requirements for optical line terminal (OLT) applications. The 1490nm DFB LD transmitter has automatic power control (APC) function and temperature compensation circuitry to ensure stable optical power and extinction ratio over all operating temperature range. The transmitter meets Class 1 eye safety per IEC60825 and CDRH standards.The receiver has a hermetically packaged APD-TIA (trans-impedance amplifier) pre-amplifier and a limiting amplifier with LVPECL compatible differential outputs. It features a Burst Packet Detect (SD) output which is LVTTL compatible. The SD output will come high after receiving the burst packet. The module provides digital diagnostic information of its operating conditions and status, including transmitting power, laser bias current, module temperature, and supply voltage. Calibration and alarm/warning threshold data are written and stored in the internal memory (EEPROM). SFP transceiver module has done sampling test under most famous brands of routers, switches, servers. The hot swappable GPON SFP transceiver is ideal for Internet Service Provider (ISP) Gigabit Passive Optical Network (GPON) communication links, other optical links. Specification Form Factor GPON SFP Power Supply Voltage 3.3V Connector/Polish SC/UPC Maxim Distance 20km DDM Supported Media SMF Warranty 3 Years Temperature Commercial /Industrial TX Data Rate 2.488Gbps RX Data Rate 1.244Gbps TX Wavelength 1490nm RX Wavelength 1310nm Power Consumption <1.5W Total Current 450mA Transmitter Type DFB Receiver Type APD TX Optical Power +1.5~+5.0dBm RX Sensitivity < -28.0dBm Extinction Ratio >8.2dB Receiver Overload >-8dBm Protocols SFF-8472, ITUT-984.2 Features Single fiber bi-directional data links asymmetric TX 2488Mbps/RX1244Mbps application 1490nm continuous-mode DFB laser transmitter and 1310nm burst-mode APD-TIA receiver Small Form Factor Pluggable package with SC/UPC Connector 0 to 70°C operating temperature Single 3.3V power supply Digital diagnostic monitoring interface Digital burst RSSI function to monitor the input optical power level LVPECL compatible data input/output interface LVTTL transmitter disable control LVTTL transmitter laser fault alarm Fast LVTTL receiver Signal Detect (SD) indication response Low EMI and excellent ESD protection Class I laser safety standard IEC-60825 compliant RoHS6 Compliance Application Gigabit-capable Passive Optical Networks (GPON) Standards Complies with SFP Multi-Source Agreement (MSA) SFF-8074i Complies with ITU-T G.984.2 Amendment 1 Complies with FCC 47 CFR Part 15, Class B Complies with FDA 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007 Complies with SFF-8472 Compatible with TR-NWT-000870 4.1 ESD sensitivity classification Class2. Compatible with Telcordia GR-468-CORE Ordering information - Gigaopto’s GPON OLT SFP Series(DFB+APD SC Simplex) P/N Date Rate (Gb/s) Wavelength (nm) Class Tx Power Rx Sensitivity Temperature GTS-SGT21-20DCB TX-2.488/RX-1.244 TX-1490nm/RX-1310nm B+ +1.5~+5.0dBm < -28.0dBm Com GTS-SGT21-20DIB TX-2.488/RX-1.244 TX-1490nm/RX-1310nm B+ +1.5~+5.0dBm < -28.0dBm Ind. GTS-SGT21-20DCC TX-2.488/RX-1.244 TX-1490nm/RX-1310nm C+ +3.0~+7.0dBm < -30.0dBm Com GTS-SGT21-20DIC TX-2.488/RX-1.244 TX-1490nm/RX-1310nm C+ +3.0~+7.0dBm < -30.0dBm Ind. GTS-SGT21-20DCD TX-2.488/RX-1.244 TX-1490nm/RX-1310nm C++ +4.5~+10.0dBm < -31.0dBm Com GTS-SGT21-20DID TX-2.488/RX-1.244 TX-1490nm/RX-1310nm C++ +4.5~+10.0dBm < -31.0dBm Ind. GTS-SGT21-20DCE TX-2.488/RX-1.244 TX-1490nm/RX-1310nm C+++ / D +6.0~+10.0dBm < -32.0dBm Com GTS-SGT21-20DIE TX-2.488/RX-1.244 TX-1490nm/RX-1310nm C+++ / D +6.0~+10.0dBm < -32.0dBm Ind. Note OEM/ODM Supported, Please Feel Free To Contact Us! Compatibility All of GIGAOPTO's GTS-SGT21-20DCB SFP optical transceiver modules are open sourced, can be coded to be fully compatible with worldwide popular brands' devices, e.g. HUAWEI MA5603T, HUAWEI MA5608T, HUAWEI MA5680T, HUAWEI MA5800T, ZTE ZXA10 C300, ZTE ZXA10 C320, ZTE C600, Alcatel-Lucent 7360, Nokia 7360, C- DATA, VSOL, BDCOM. Please refer to the following table for detailed compatibility, please feel free to contact us. Corresponding Compatible Brand/Part Number Brand Part Number Brand Part Number Gigaopto GTS-SGT21-20DCB Alcatel-Lucent 3FE53441AA 01 HuaWei GPON-OLT-CLASS B+ Nokia 3FE53441ACAA ZTE GPON-OLT-Class B+ Calix 100-01782 ZTE 33030100152 Dasan MXK-GPON-SFP-B+-RSSI Ubiquiti UF-GP-B+ Cisco SFP-GPON-B BDCOM OLT-GSFP-B+ Calix 100-01836 Broadex D24364-SSCB SuperXon SOGP4321-PSGB WTD RTXM167-522

Safe Reliable IP 68 Fiber Optic Splice Closure 120 cores in Manholes Quick Detail: IP68 Heat shrink type waterproof fiber optical splice closure.1 oval port+4 round ports;Max 5 trays and 120 cores;Suit for 8-25mm cables;Used for aerial wall mounted,pole mounted,man hole,duct mounting and pipeline,direct buried..etc Description: 1. Protection grade:IP68 2. Material:PP,ABS 3. Number of cable ports: 1 big oval port and 4 small round ports 4. Maximum Trays: 5 trays 5. Maximum Cores:120(singlel core) 6. Dimension (HxD):430mm *130 mm 7. Package material:Export Carton 8. Weight:2.5-3.0Kg 9. Cable diameter range:8mm-25mm 10. Sealing way of cables:Heat shrinking 11. Quality warrenty:2 years 12. Life span:more than 25 years Applications: Aerial,Wall mounted,pole mounted,manhole,duct mounting,pipeline,direct buried..etc Specifications: Model No.of ports Cable range Max trays Max Capacity Dimensions GJS20-DR03A 5(1 oval+4 round) 8-25mm 5 120 cores 430×ф130mm Competitive Advantage: Easy & fast installation without special tools,suit for uncut cables Superior sealing performance(free sample for testing) The closure can be repeatly used many times. The cables can be fixed via 3 points,safe and reliable Enough space for surplus fibers inside the closure Flexible branching for fibers loose leaf type of splice tray fixing,easy operation&maintain Modular fiber management system Pictures: Safe Reliable IP 68 Fiber Optic Splice Closure 120 cores in Manholes 0Safe Reliable IP 68 Fiber Optic Splice Closure 120 cores in Manholes 1Safe Reliable IP 68 Fiber Optic Splice Closure 120 cores in Manholes 2

Product Description Pallet PLC Splitter, 19" Rack Mount 1x64 SC / UPC, Used for FTTH Pallet type fiber optic PLC splitter has no open wire, the fiber optic cable is in a metal box with many high quality optical fiber adapters. According to the quantity of the adapters it mounted, It will be fixed to the fiber optic splice outdoor cabinet or optical distribution frame. The tray type PLC splitter can be inserted into the fiber optic tray directly. It is suitable for various types of optical fiber splitter, wave demultiplexer and other integrated installation and use. FOC COMMUNICATION CO., LTD provides a various of 1xN and 2xN PLC 1U rack mount type splitters, including 1x2, 1x4, 1x8, 1x16,1x32,1x64 1U rack mount type PLC splitter and 2x2, 2x4, 2x8, 2x16, 2x32, 2x64 1U rack mount type PLC splitters. Features Configuration Pallet Type 1x64 Fiber Type Single Mode G.657A1 Connector Type SC/APC Low Insertion loss Low PDL High Return Loss Uniform Power Splitting Compact Design Wide Operating Wavelength Wide Operating Temperature Excellent Environmental & Mechanical Stability Qualified Under Telcordia GR-1221 and GR-1209 Applications Telecommunications , Local area network Fiber to the home Video transmission Fiber optic sensing Testing instruments CATV Optical Specifications Parameter Unit Specification (P Grade) Channel Number 1X2 1X4 1X8 1X16 < , br>1X32 1X64 Operation Wavelength nm 1260～1650 Ins , ertion Loss (Max.) dB 4.3 7.4 10.7 , 13.9 17.2 21.5 Unifor , mity (Max.) dB 0.5 0.8 1.0< , br> 1.4 1.6 2.0 Polarizati , on Dependent Loss dB 0.2 0.3 0.3 0.3 0.3 0.5 Return Loss dB ≥50 Directivity , dB ≥50 Operating Temperature ℃ -40～+85 Sto , rage Temperature ℃ -40～+85 Parameter Unit Specification (P Grade) Channel Number 2X2 2X4 2X8 2X16 < , br>2X32 2X64 Operation Wavelength nm 1260～1650 Ins , ertion Loss (Max.) dB 4.3 7.6 11.0 , 14.8 17.9 21.5 Unifor , mity (Max.) dB 0.8 1.0 1.2< , br> 1.5 1.8 2.0 Polarizati , on Dependent Loss dB 0.2 0.3 0.3 0.3 0.3 0.5 Return Loss dB ≥50 Directivity , dB ≥50 Operating Temperature ℃ -40～+85 Sto , rage Temperature ℃ -40～+85 Not , e: All the data above does not include connectors. Ordering Information PLC Port Fiber Type Input Output Pigtail Length Connector PLC 0102=1x2 0104=1x4 0108=1x8 0116=1x16 0132=1x32 0164=1x64 0204=2x4 0208=2x8 0216=2x16 0232=2x32 0264=2x64< , br> 1=G652D, 2=G657A L=900µm Loose tube, S=2.0mm, R=3.0mm, 0=Adapter L=900µm Loose tube, S=2.0mm, R=3.0mm, 0=Adapter 05-20=0.5--2.0m, 0=Adapter, X=Others FU=FC/UPC, FA=FC/APC, SU=SC/UPC, SA=SC/APC, ST=ST/UPC, LU=LC/UPC, LA=LC/APC, 00=None, X=Others FTTH Pallet Fiber PLC Splitter 1650nm 19" Rack Mount 1x64 SC UPC 0 We can produce many serials of PLC splitters including: 1X2, 1X4, 1X8, 1X16, 1X32, 1X64, 2X4, 2X8, 2X16, 2X32, 2X64 with following package Bare fiber series Mini loose tube package ABS Module type LGX box type Rack Mount patch panel for PON application. Wall Mount patch panel for PON application Inline fiber optic splice closure type Erect fiber optic splice closure type

MPO (Multi-Fiber Push-on) is the first generation of clip clamping multi-core optical fiber connector. MTP/MPO cables are composed of MTP/MPO connectors and optical fibers. MTP/MPO connectors have a female type (without pins) or a male one (with pins). And a white dot is for identifying fiber position in connectors. MTP/MPO connectors largely increase the cable density and save circuit card and rack space, which are well suited for current 40G/100G cabling and future network speed upgrades.

1U Rack Mount Enclosure Drawer Type 12 Core 6 Port Fiber Optic Patch Panel Description: Rack Mount type fiber optic enclosure patch panel is an integrated unit for fiber distribution, these equipment function is to fix and manage the fiber optic cables inside the box as well as provide protection. There different models to fit for 12core 24core 48core 96core 144core 288core fiber applications. They can be with different adapter interface including the SC, ST, FC, LC MTRJ, etc. related fiber accessories and pigtails are optional. Product details Suitable Adapters SC LC Material Cold Rolled Steel Plate Available Cable Outdoor or Indoor Cable Outlet 6 Port Installation way Rack Mount Dimensions 485mmx295mmx47mm(1U 19") Applications Rack Mountable Cabinet in Data Center Connector Capacity 6pcs SC/LC connectors Connector Type SC LC FC ST Location Cabinet Usually Location of Use Data Center Number of Trays 1 Splice Tray Product Type ODF/Fiber Patch Panel Splice Capacity 24 fibers Feature: 1. Made of cold-rolling steel, static spreading-plastic, small dimension and exquisite and easy for operation. 2. The box has a pothook, which is convenient to install and dismantle. 3. The splice tray could be piled one upon another, flexible to turn 4. Adjustable clamp seal ring and reinforce configuration, which could adjust different sizes of cables flexibly to make sure the cables are clamp tightly. 5. The indoor type is of excellent seal performance, which could prevent water from entering effectively. 6. The box is of unique structure, reasonable layout, and has adequate room for operation. Application: 1. Telecommunications subscriber loop 2. FTTH 3. LAN/WAN 4. CATV more models SIZE Drawer Type Fiber Patch Panel 1U 12/24 Port SIZE:485*295*47MM Drawer Type Fiber Patch Panel 2U 48/72 Port SIZE:485*250*90MM Drawer Type Fiber Patch Panel 3U 96 Port SIZE:485*310*120MM Drawer Type Fiber Patch Panel 4U 144 Port SIZE:485*295*180MM Details photos: 6 Port Fiber Optic Patch Panel SC 12 Core 1U Rack Mount Fiber Enclosure 06 Port Fiber Optic Patch Panel SC 12 Core 1U Rack Mount Fiber Enclosure 16 Port Fiber Optic Patch Panel SC 12 Core 1U Rack Mount Fiber Enclosure 2

Product Description 12D-FB BC TC PE NO.7101414 Construction Parameters: Inner Conductor 4.40mm Bare Copper Dielectric 12.40mm Foamed PE Shield Bonded AL-Foil Outer Conductor Nom. 13.20mm Tinned Copper Braid Jacket 15.60mm PE Black Jacket Thickness Application 12D-FB Cable Inner Conductor BC with Outer Conductor Tinned Copper Braid 50Ohm Coaxial Cable 0 Electrical Characteristics: Capacitance 82 pF/m Impedance 50 Ω Velocity of Propagation 81% Inner Conductor DCR 1.2 Ω/km Outer Conductor DCR 4.5 Ω/km Shielding Effectiveness ≥ 80 dB Return Loss ≥ 20 dB RoHS Yes Mechanical and Environmental Properties: Cable Bend Radius 78mm Operating Temp Range -40 ℃ to +85℃ Cable Diamensions 15.60mm Attenuation(20℃): Frequency (MHZ) Max Attenuation (dB/100m) 150 3.40 280 4.70 350 5.30 400 5.70 800 8.50 900 9.10 1200 10.80 1500 12.30 1900 14.20 2000 14.60 2500 16.60 Order Informations: Marking HELLOSIGNAL 12D-FB 50 Ohm COAXIAL CABLE ×××M Package Inquired Length on Roll, Wooden Spool, Pallet … Delivery time Normally 25 days after received the deposit. Brand HELLOSIGNAL® OR OEM

L3 managed 8 port Gigabit / 10G Uplink SFP+ Port Smart Network industrial Managed ethernet Fiber Switch Description The OFS-MXF8-3 series is a high performance 8-port industrial managed 1G/10G Ethernet switch with 8 1G/10G SFP+ ports. The switch supports STP/RSTP/MSTP. It also supports web-based network management, VLAN, QoS, SNMP , IGMP snooping and other network functions. LED indicators provide connection status when using the SFP option. Suitable for many applications such as intelligent transportation systems, IP surveillance and industrial networks. The rugged design with industrial level 3 ESD protection makes it suitable for many applications such as intelligent transportation systems, IP surveillance and industrial networks. This product is available in a mounting ear configuration.This product is available in a mounting ear configuration. 8× 10-Gigabit ports unlock the highest performance of your 10G/Multi-Gig bandwidth and devices, and provide up to 160 Gbps of switching capacity.Lightning-Fast Connections. Provides lightning-fast connections to 10G NAS, Server, 10G PCIe Adapter/ NIC, gaming computer, 10G WiFi 6 AP, 8K video, and more.Ideal for Various Scenarios. Built for lightning-fast connections in business and home offices, workstations, LAN parties, and home entertainment. Features 8* 1G/10G SFP+ Ethernet ports STP / RSTP / MSTP redundancy protocols and standards SNMPv1/v2c/v3 & RMON & Port base/802.1Q VLAN network management IGMP Snooping multicast function Support ARP/RIP/OSPF/OSPFV3/BGP/Router Discovery/VRRP/ Route-Map/BFD three- layer routing WEB, Telnet, SSH, Console (CLI) open and close port, binding MAC and port 802.1x network access control 802.1Q protocol, Isolate network flow Radius Centralized password management Overcurrent protection and reverse polarity protection Unique DIN mount design makes mounting and removal simple Built-in 12V lead-acid battery charging circuit (optional). Please send us an inquiry and you will get the best price ! Ordering Information OFS-MXF8-3 8*1G/10G optical port, web management, CLI command line, L3,external power supply. L3 managed 8 port 1G/ 10G Uplink SFP+ Port Smart Network industrial Managed Ethernet Fiber Switch 0L3 managed 8 port 1G/ 10G Uplink SFP+ Port Smart Network industrial Managed Ethernet Fiber Switch 1L3 managed 8 port 1G/ 10G Uplink SFP+ Port Smart Network industrial Managed Ethernet Fiber Switch 2L3 managed 8 port 1G/ 10G Uplink SFP+ Port Smart Network industrial Managed Ethernet Fiber Switch 3L3 managed 8 port 1G/ 10G Uplink SFP+ Port Smart Network industrial Managed Ethernet Fiber Switch 4 L3 managed 8 port 1G/ 10G Uplink SFP+ Port Smart Network industrial Managed Ethernet Fiber Switch 5 Why Choose US: Advantage of our company : ①　National High-tech enterprise certification； ②　11 years optical innovative& production team ③　fully advanced production line and QC system ④　products are highly cost effective, quality stable and reliable ⑤　good characteristics of exclusive exquisite design and abundant products series. ⑥　Professional One stop supply & service; ⑦　OEM&ODM available; ⑧　Reliable and Timely customer services; We are pleasure to have you in touch and help you more ! to join us and make a Win-Win business !

Description of Laser Optcial lens: The base material is Impoeted quartz JGS1 material, which is transparent. It is finely processed by grinding, polishing, coating and other processes. From the side, it shows light color and mainly used in laser cutting to prevent splashing of sundries and avoid splashing to damage the lens. It is widely used for laser cutting machine, laser marking machine , precitec laser hand. Product name Fiber optical lens Protection Windows Quartz 34*5 15kw Fiber Optical Lens For Precitec Lasermech Machine 0 Coating 1064nmAR Dia tolearance -0.1mm Thickness tolearance ±0.1mm Chamfer 45 degree*0.2mm Application laser welding/cutting/marking machine Material Imported Quartz JGS1 Advantages 1. Top quality glass with CE certificate,exporting to more 60 countries in the world 2. Unique designed strong wooden case, solving the problem of breakage 3. Professional sales team, offering personalized and dedicated services. 4. 24-hours online, we could discuss the item whenever and wherever.