Construction, Woodworking & Agriculture Machinery

PTO Shaft Replacement for Weasler 2000/14 Series NA 14 Series PTO Jocket, shaft and yoke to meet your requirements The Centerline from the End of Shaft: 35-2/3 in. The PTO shaft drive yoke is 1 in. 1-1/8 inch. Solid rectangle bore to allow for ease of operation PTO tractor yoke runs at 58 HP/43 Kilowatts @ 1000RPM or 38 HP/28 Kilowatts @ 540RPM to maximize efficiency. Weight: 12.7 lb/6 kilograms Extension size: 25-5/8 in. PTO Shaft as well as Agricultural Gearbox The agricultural gearbox and the PTO shaft two components collaborate to transfer power mechanically between the farm tractor. PTO shafts PTO shaft converts the engine's energy to hydraulic pressure. It allows the tractor to lift huge loads. If it's functioning properly it lowers the chance of damaging the tractor and to the person operating it. If used properly it can be a crucial part of a tractor however, it is also susceptible to becoming inoperable. When selecting the best agriculture gearbox take into consideration the durability and the mechanism of the item and the material used. A sturdy gearbox will last for years and will avoid the need for frequent replacements. A good agricultural gearbox is durable for a long time You don't need to replace it over and over. It can be expensive therefore, you must consider your needs when buying an agricultural gearbox or PTO shaft. HZPT provides PTO shafts, agricultural gearboxes, and more for sale at cheap cost! Contact us today if you are interested!

Minimum Order: 50

Power take off (PTO) can be described as a sophisticated mechanism that lets an instrument draw energy from the engine and then transfer it to a different application. It operates as a gearbox that can be placed on an engine's transmission. The Power Take-Off shaft (PTO shaft) is a crucial component that was designed and produced for use in continuous, heavy-duty operation. A high- quality PTO shaft must be sturdy enough to withstand both torsionally and shear stress and reduce vibration. Ever-Power makes Cold extruded PTO shafts for all kinds of agriculture vehicles. Our PTO shafts are extremely reliable and durability when used in daily use. EP Group has been recognized globally as a trustworthy global supplier. Our modern manufacturing processes and highly skilled engineers guarantee the best quality of our components. Specifications Of W 2600 Series PTO shaft 100-160cm (40"-63") Cross to Cross Length, 100-160cm (40"-63") overall length W2600 Series. 42mm x 104mm x 115mm (approx.) Star Profile Drive Tube. 90KW-120HP @ 540 rpm, 144KW-192HP @ 1000 rpm. Standard Shaft Includes: Security Guard. NO ND Yokes. Accepts a non-standard yoke. Reduce the HP rated by 40% in extreme conditions.

Minimum Order: 50

PTO Shaft to New Holland Round Balers Our PTO Shaft Adaptable Models New Holland Round Balers Models: BR7050, BR7060, BR7070, BR7080, BR7090 New Holland calls for CAT3, CAT4, and CAT5 constant-velocity drivelines, based on the model and different torque limiters. For input shafts, we recommend 1.375-6 and 1.375-21. We can help you with your requirements. Available for tractors that use 1.375-6 or 1.375-21 Input shaft 1.375-6 or 1.375-21 Other combinations are also available. Round Baler PTO Shaft Maintenance The PTO shaft needs to be greased regularly to prevent universal joint from failing, and also to prevent the shaft from sizing. If you do not maintain your shaft's grease regularly or as specified in the PTO maintenance schedule of the shaft can result in the end thrust damaging the gearbox in the implement. It is recommended that you grease regular universal joints every 20 hours , or every 8 hours in extreme situations. Remember! grease follows the simplest route through internal ports, eventually reaching those four cross bearings. A high temperature or poor quality grease that is baked in one port can block grease from getting to the bearing, leading to failure of the individual cross bearings. Make sure you completely remove the guard cover to ensure that grease flows across the entire cross bearing. Greasing the small access hole isn't good enough. Check the condition of the PTO safety guards. If they're damaged or are in poor condition , replace them to ensure the safety of the driver. Round Baler PTO Shaft Length Requirements PTO shaft PTO shaft acts as the mechanism which supplies the power to your device. Therefore, it is crucial to be aware of how it functions to ensure the safety of users. It is also essential that you are aware of the maintenance specifications to avoid any mechanical issues. PTO shafts come with a rating and are not always interchangeable with round balers or implements. It is therefore essential to match the correct shaft on the appropriate implement in accordance with the specifications of the manufacturer and also to ensure that it's the right length. Long: The length of the PTO shaft is determined by setting up an implement in an open baler round in the beginning. If you want to reduce the length of PTO shaft is required , the operator should use the supplier's method to reduce the shaft to the proper length. This is usually accomplished by measuring the output shaft of the round baler and then transferring the input shaft of the place it the point at which the PTO shaft is at its narrowest. Too long When your shaft for PTO is excessively long (or are the Telescopic tubes jammed) "end thrust" could occur, which could cause damage to the internal PTO drive, clutch for implements or gearbox, possibly invalidating your warranty on the machine. Too short: If the shaft is too long, it may possibly split from the implement, causing significant safety concerns and possibly injury. PTO Shaft for Agricultural Gearbox Agricultural equipment includes various PTO shafts. Each shaft is connected via two yokes and is able to rotate between the 540 and 1000 rpm. Safety Universal PTO shield is typically placed on both sides of a shaft for PTO to safeguard the operator. They are also present in tractors as well as agricultural equipment, which ensures maximal effectiveness. Internal yokes can also provide additional security.

Minimum Order: 50

PTO Shaft to New Holland BigBaler Square Balers 335 360 Our research has shown that the majority of tractor designs employ 1.375-21 Splines. The input shaft has 1.750-6 Splines. Other combinations are also available. The PTO Shaft is what it's called. A PTO shaft transmits power of an engine to an PTO shaft driven attachment. This allows the tractor to run a range of tractor equipments, such as flail mowers, wooden chippers excavators, rotary tillers and many more. PTO shaft connections on tractor aren't standard, and can lead to issues with joining with the PTO shaft. For instance, some older models have the connection flange located closer to the tractor making it difficult to connect, creating a danger to safety. PTO Shaft Adapters To prevent issues with connectivity, you may think about PTO shaft adapters to your tractor. They PTO shaft adapter expands the connection to the implement, allowing more space to allow to allow the PTO shaft to rotate without touching any other part of your tractor or implement. As a safety measure it's a good option to purchase PTO shaft adapters in order to guarantee that they are compatible with the model of your tractor you are using. How do I Find the the PTO's Shaft Size? If you have farm implements in conjunction with your tractor, it is likely that you depend on the PTO shaft to transmit the power of your tractor to the equipment. To accomplish this transfer, you must connect the driveshaft that is attached to your implement and the stub shaft on the PTO tractor. Depending on the machine the shafts that are attached are able to be rotated at 540 or 1,000 rpm in the course of the operation. It's crucial to ensure that you to ensure that your PTO shaft be of the proper dimension. The first thing to consider is that there should at a minimum of a one-third gap of the tube and the shaft. In the case of a slip- sleeve the distance should be about 3 inches. When the shaft's length is excessive it will eventually bottom out, creating conflicts in between the tractor as well as the shaft. In the majority of cases this can cause damage to one , the other or both. When you're dealing with two identical-length tubes within your shaft, you'll have split both the tubes as well as both shields to the proper length. If you have two tubes of different lengths you are able to reduce only the longer portion as well as the shields. When you put the unit back together again, it will be the right, shorter length around. How do you remove the Pto Shaft from the Tractor? Tractors equipped with PTO (PTO) drive shafts that can be used to all kinds of PTO-driven tools. When the shaft for the implement's PTO engages the drive shaft for the tractor's PTO the shaft turns 1,000 minutes per hour. The PTO shaft supplies mechanical energy to the machine. Male drive shaft of the tractor is equipped with spikes that join with that female drive shaft that is on the implement. The locking pin, or button locks them together.

Minimum Order: 50

PTO Shaft to fit New Holland Dis Mower Discbines Our drive shafts for PTO can be adjusted to the following models of disc mowers: New Holland Discbines 1431and 1432 Model 411 1409, 1410 1411 14, 1411, 1441, 1442 14, 1431, 143 H7220, H7230, H7320, H7330, H7450, H7460, H7550, H7560 IH DC 132, Case IH DC 132 Parts of Pto Shafts. Pto Shaft It is important to know the dimensions, measurements horsepower, sizes, and the agriculture PTO shaft components in order to select the right PTO shaft for your farm equipment. Although the U-joints and yokes are required for operation however, the safety chains as well as the shield are vital components in the PTO shaft to ensure you are secure during operation. Internal Yoke: There are two located on both sides of the PTO shaft: implement and tractor. It is joined on the end of the drive. Universal Joint- There are two joints at both ends of the PTO shaft. External Yoke- There is a second on both sides on the PTO shaft. It's got an "Y" shape that connects to the U-joint, and an opening for females. Safety Chains - The chains ensure the PTO shaft to the equipment as well as the tractor. Safety ShieldCones placed at both the ends. Different Models PTO Shaft for Sale Every discipline has several PTO shafts as well as the combination clutch. Three Different Shafts for Pto. Shafts The kind of PTO shaft you pick will depend on the task you're expected to perform. If you're plowing or mowing or shredding, you'll need an PTO shaft that is suitable for every task. It will also help safeguard your machinery from excessive stress, hits or tension. Non-Shear PTO Shaft This design is for equipment that is not intended to withstand sudden stops. It's a yoke-to yoke arrangement. This is a good option for larger mowers as the motions should be smooth, as there won't need to be any moments that are obstructed or stopped. Shear Pin PTO Shaft The end yoke comes in two pieces and utilizes a shear pin to keep them in place for operation. The pin absorbs shock when there is sudden stop in order to prevent damage to the driveline. It can be utilized in conjunction with other equipment, such as chippers. Slip Clutch PTO Shaft Slip Clutch is made to shield your tractor and the attached equipment from being damaged due to internally sliding- which allows the movement of an object when it hits. For instance, when changes in the season, stones and rocks are brought to the surface and when they are struck you need the impact to be absorbed so that you won't cause damage to the gearbox. PTO Shaft Length Limit Its Power Take Off (PTO) shaft is the part that supplies energy to your device. Therefore, it is vital to know how it functions to ensure safety for the user. It is also crucial for you to know the maintenance specifications to avoid mechanical issues. PTO shafts are rated but are not interchangeable with tractors or other implements. It is crucial to attach the right shaft to the machine in accordance with the specifications of the manufacturer and ensure that it's the correct length. length: The length of the PTO shaft is measured when installing an implement on an tractor in the very first. If a shorter PTO shaft is needed then the operator should follow the formula supplied by the supplier in order to trim the shaft according to its proper length. This is typically accomplished by measuring the output shaft of the tractor and putting the input shaft so that the PTO shaft is at its narrowest. Too long When your shaft for the PTO is excessively long (or in the event that the telescopic tubes are seized), "end thrust" may occur. This could ruin your tractor's internal PTO drive, or the clutch for your implement and gearbox, possibly invalidating your warranty. Too short: If the shaft is too long it may break away from the device, creating serious safety risks and causing injury. How can I cut the PTO Shaft in the Correct Length? When your PTO shaft gets too big, the shaft may be unable to move during the lifting of the 3-point hitch. The damage could be to the chipper's bearing and the PTO in the tractor. In the event that it is found that the PTO shaft becomes too large, it should be cut. Equal amounts should be cut to shorten both PTO half. 1. Install the chipper on the three-point hitch on the tractor. 2. Cut the engine off and remove the keys. Then lower the chipper onto an even and solid surface. 3. Take the 3-point hitch up up so that the shaft for power intake for the crusher is the same height that the power intake shaft of the tractor. This will ensure that both the PTO along with the power intake shaft should be in the closest proximity in this position. 4. Remove the PTO shaft off. Connect one end of the shaft with the chipper to ensure that you can lock the pin. secure. Set the opposite portion of the shaft at an end of the tractor's PTO. Place the other end of the chipper on the side. Mark in the shield how much has to be removed. The tubes need to be cut to a length that they can't be able to reach the bottom from the chipper positions. 5. Slice the tube of plastic. 6. Cut a piece of the profile tube. It should be the same length as the one you removed from the shield. Cut the other half of the PTO shaft to be the same length. 7. Cut sharp edges off of the tubes for profile. PTO Shaft Maintenance The PTO shaft must be lubricated regularly to prevent universal joint in good condition and also to stop the shaft from sizing. Inability to grease your shaft on a regular basis or in accordance with the guidelines stipulated in the PTO maintenance schedule of the shaft can cause end thrust, which could lead to damaging the gearbox of the implement. It is advised to grease standard universal joints once every twenty hours, or 8 hours in extreme circumstances. Remember! Grease travels the simplest route through internal ports that lead to four bearings. Poor quality and overheated grease that is baked in a single port will block grease from reaching the bearing, and will cause damage to each of the cross bearings. In the first place, make sure you complete opening the guard cover so that grease gets across all bearings. The small access hole isn't good enough. Also, make sure to check the condition of the PTO security guards. If they're damaged or damaged, you should arrange for replacement while ensuring the safety of the operator. Agricultural PTO Shafts Applications We all know that nowadays, everyone places significant importance to farming production particularly in the areas of cultivation, harvesting and maintenance. This is an essential component of improving output. However, we need to discover that our farmlands are not the bustling life of suffering farmers however, a vast portion of the land is cultivated using equipment and machinery. Farmers and individual operators are during the work and this demonstrates the importance to agricultural equipment. There is also the use for PTO shafts for agricultural machines. For instance the mower, sprayer harvester, field return machine, etc. will have a PTO shaft. But the PTO shaft is different due to different agricultural machinery's various designs and functions. There are a variety of types of HZPT's PTO shafts. You can select the right PTO drive shaft in accordance with the model that is used.

Minimum Order: 50

Basic Information. Model NO. PTO Drive Shaft-YY Appearance Shape Round Journal Surface Roughness 0.63-0.16mm Transport Package Trademark Wooden box no brand Origin China Code HS 848390009 Description of Product CE Certification for Agricultural Large Angle Tractor Supply 6 Spline PTO Drive Shaft 540mm used for Bush Hog With Yoke Adapter Parts Product Description PTO drive shaft The brand-new replacement PTO shafts suitable for Finish Mowers, Tillers, Spreaders, Hay Tedders and many other applications. PTO is one of the series 4, and is designed for 40HP, it comes with 1 3/8" 6-spline push pins at both ends to facilitate installation. With safety shield included. the PTO has a length of 43" from the end to the end and has an extended length of 58" maximum length extended. These PTO shafts work with these Finish Mowers: Bush Hog ATH 600, ATH 730, ATH 800, FTH 600, FTH 480 FTH 720 MTH 600, MTH 720 Series Mowers Landpride: FDR1548, FDR1572, FDR1648 the FDR1660, FDR1672, and FDR2548, FDR2560and AT2660, FDR2572; Series Mowers; Kubota: B342A, BL348A Caroni TC480, TC590, TC710 T910 with Spline Input Shaft; Many models that have input shafts that splined, earlier models had models with a smooth input shafts; 1. PTO Drive Shafts PTO SHAFT With QUICK release yoke and over-running CLUTCH(RA) You can choose the length Chinabase is a leading manufacturer of PTO SHAFTS to agricultural tractors and farm equipment from China. We supply more than eight dimensions of PTO shafts. We also offer a complete assortment of safety equipment to protect agricultural equipment. Our products are distributed in America, Europe and all around the world. We offer top quality goods at the most affordable cost. Here are some tips on how to purchase your shafts for PTO: 2. Overall length closed (or crossing to cross) of the PTO shaft. 3. Pipes or Tubes We've received Triangular profile tube as well as Lemon profile tube in every series we have. There are also stars tube, splined and other tubes with profiles, however only for specific size. 4. End the yokes We have 13 varieties of splined-yokes, and 8 varieties of plain bore Yokes. I'll suggest the standard kind for reference. It is also possible to email drawings or photos to us in case you are unable to find the item you are looking for on our catalogue. 5. Safety devices, clutches or other safety equipment I'll provide the information of the safety devices to provide information. We already have Free Wheel (RA) and a Ratchet limiter of torque (SA), limiter(SA), The torque of the shear bolt is limiter(SB) Three types of friction torque limiters (FF,FFS,FCS) along with Overrunning couplers(adapters) (FAS). 6. If you have any additional specific requirements regarding the use of plastic guards, connecting methods or color of the paint packaging and so on. If you have any other special requirements, be sure to let me know. Tubes of all kinds Spline tube Lemon tube Star tube Trigonal tube The function of the PTO Shaft Drive Shaft Parts & Power Transmission Use of PTO Shaft Sorts of Tractors & Farm Equipment Yoke Types for PTO Shaft Double push pin, Bolt pins Pins split Ball attachment, Quick release, Collar ..... Processing Of Yoke Forging PTO Shaft Plastic Cover YW; BW; YS; BS; Etc The colors of PTO Shaft Green; Orange and Black. PTO Shaft Series T1-T10; L1-L6;S6-S10;10HP-150HP with SA,RA,SB,SFF,WA,CV Etc Tube Types for PTO Shaft Lemon, Triangular, Star, Square, Hexangular, Spline and Spline, Ect Processing Of Tube Cold drawn Spline Types for PTO Shaft 1 1/8'' Z6;1 3/8'' Z6; 1 3/8'' Z21 ;1 3/4'' Z20; 1 3/4'' Z6; 8-38*32*6 8-42*36*7; 8-48*42*8; Application Company Profile The factory we operate is one of the renowned producer of PTO shaft yoke as well as universal joint. We produce high-end PTO Yokes for all kinds of machines, vehicles, and construction equipment. Each product is constructed using a an adjustable lighter. The company currently sells its goods all over the world, particularly in North America, South America, Europe, and Russia. If you're interested in any of our products don't hesitate to reach us. We look to become your supplier in the near future. Packaging & Shipping Certifications Related products Click the image to read more about related products Installation Instructions PTO SHFT INSTALLATION DIRECTION Assembly installation 1 plastic pipe that is press-fitted and cap made of plastic, 2 Fill the groove of the horn by applying oil 3. The nylon bearing should slide into the groove. Align the nylon bearing with the plastic cover Disassembly 1. Remove the bearing clamp made of nylon (three places) using a screwdriver and then remove the steel pipe from the plastic cover for protection. 2. The nylon bearing must be removed from the groove on the yokes. 3. Repetition the above steps for the second side. SLOWING THE PTO DRIVESHAFT 1. Eliminate your safety cover. 2. Reduce the length of the outer and inner tubes to the desired length. The inner and the outer tubes must be cut by identical lengths at a at a time. 3. The edge of drives using an instrument and then remove all files from the tubes. 4. Cut the inner and outer plastic pipes in accordance with the length required and the inner and outer pipes should be The length of the shortened limbs was also reduced at a time. 5. Lubricate the internal drive tubes and then reassemble them using the protection shield. Examine the lengths of the minimum and maximum of the driveshaft mounted within the equipment. In good working order the drive tubes must extend by 2/3 while the tube made of plastic must never be separated.

Minimum Order: 50

PTO Shaft to fit Single Auger Twin Auger and the Total Mix PTO shaft used for Jaylor Vertical Mixers TMR The device transmits motion in a single direction as the tractor drives the implement. In the stop phase, the tractor PTO shaft is disengaged, and the machine moved. The transmission is cut off. This device assists in operating machinery that have high-speed inertia due to when the stop phase is in place this tractor's PTO is removed from the machine being driven. Original Equipment is listed on the left as Size 6, or 8 copy of BYP. )Based on HP at 60 HP or lower = CAT4 = Size 6. ******* greater than 60 HP = CAT5 = Size 8. Jaylor provides Constant Velocity shafts or standard PTO We also supply all components for the feed mixer. MAINSHAFT CVO: Constant Velocity Category Series Tractor Tractors that have 1.375"-6 PTO 4 (60 HP@540 RPM) S6 1.375-6 5 (90 HP@540 RPM) S8 1.375-6 Tractors that have 1.375"-21 PTO 4 (60 HP@540 RPM) S6 1.375-21 5 (90 HP@540 RPM) S8 1.375-21 Tractors that have 1.750"-20 PTO 4 (60 HP@540 RPM) S6 1.750-20 5 (90 HP@540 RPM) S8 1.750-20 Shear Bolt Yokes: Part Number Model Diameter No of Splines C-to-bolt Bolt c-e Length Torque Size 6 Shear Bolt Yokes 6060H3702R LB 1.375 21 55 M10x50 134 2700nm BTB06215510A LB 1.375 21 55 M10 4.8 2700nm 6060H0302R LB 1.375 6 55 M10x50 134 2700nm BTB06385510A SB 1.375 6 55 M10 2500nm BTB06205510A SB 1.750 20 55 M10 2500nm BTB06345510A LB 1.750 6 55 M10 4.8 6060H3802R LB 1.750 20 55 M10x50 134 2700nm 6060H3707R LB 1.750 27 55 M10x50 2700nm 6060H0402R LB 1.750 6 55 M10x50 134 2700nm Size 8 Shear Bolt Yokes 6060M3702R LB 1.375 21 50mm M12 143mm 3800nm BTB08215712A LB 1.375 21 M12 pin QD 3500nm 6060M0302R LB 1.375 6 50mm M12 143mm 3800nm 6060M0307R LB 1.375 6 50mm M12 143mm 3500nm BTB08385712A LB 1.375 6 M12 pin QD 3500nm 6060M3802R LB 1.750 20 50mm M12 143mm 3800nm BTB08205712A LB 1.750 20 M12 pin QD 3500nm 6060M3902R LB 1.750 27 M12 6060M0403R LB 1.750 6 50mm M12 143mm 3800nm BTB08345712A LB 1.750 6 M12 pin QD 3500nm PARTS OF THE PTO SHAFTPTO Shaft for Jaylor Vertical TMR Feed Mixers It's crucial to understand the dimensions, measurement horsepower, dimensions, and other PTO shaft components in order to select the correct PTO shaft that will fit in your equipment. Although the U-joints and yokes are essential for their function however, the safety chains as well as the shield are the most important components that make up the PTO shaft, which will help ensure your safety during operation. Internal Yoke: There are two of them, situated on both sides of the PTO shaft, namely the implement and the tractor. The welded end is attached onto the drive side. Universal Joint- There are two at each end of the PTO shaft. External Yoke - There are two on both sides on the PTO shaft. It is an "Y" design to connect to the U-joint as well as an opening for females. Safety Chains - The chains anchor the PTO shaft onto the machine and also the tractor. Safety ShieldCones located at both the ends. Size is the most important aspect of the PTO shaft Whatever task you'll use the PTO shaft for it is essential to are using the right dimension. The manufacturer will provide length recommendations to help to get an idea. When measuring the length of a PTO shaft, you can use the tape measure and take measurements from the outside of each yoke in order to get the length closed. The size of the series should be in line to the horsepower that your tractor is equipped with. Two different speeds are employed typically when using tractor PTO shafts, those of 540 (type one) and the 1000 (type three) RPM.

Minimum Order: 50

PTO Shaft for Flail Shredders Alloway S15CD S20CD S25CD S27CD Our PTO shaft is customized to meet the requirements of any of the models below: Alloway Shredders Modelles S15CD, S20CD, S22CD, S25CD, S27CD Ever-power Shredders employ a variety of clutches at the connecting to the end. Some are unique and have to be replaced in a similar manner. Others are more general and are replaceable by various devices. The main thing to remember is whether or whether the input shaft is fitted with grooves, such as those on the PTO output of a tractor. PTO Shaft for Flail Shredders If there's no groove, the clutch has to be replaced with an identical unit. We believe that protection against overrunning is more important than torque protection. 3 Point Assemblies Alloway Shredder PTO with 3-point and 2-point attachmentsA 55N splined PTO Assemblies are available in the 540 and 1000 RPM. Please call us with specifics needed Pull Type Alloway Shredder PTO Trailing Hitch55N CV PTO that is splined 55N Bolt-through style device to overrun shafts without grooves Part # Y5991 How do you perform daily inspections on shafts of PTO? A typical agricultural transmission shaft consists of the shaft tube, an expansion device and a universal joint. While the shaft is used to connect and joins various components but the components of circular objects that be rotated and moved are typically constructed of lightweight alloy steel pipe that has good resistance to torsional forces. 1. To ensure that the balance is maintained that the agricultural shaft is in focus should be given to the removal of the weldment for balance as well as the brand new PTO shaft components must be supplied in a corresponding fashion. In loading the shaft of an agricultural tractor pay attention to the mark on the assembly for the extension device and verify that the flange yoke remains in the correct plane. When disassembling and repairing the transmission shaft of agricultural tools The assembly mark must be placed on the expansion sleeves and the flange shaft in order to preserve the original connection while reassembling. 2. frequently check the fastening of the hanger on the agriculture transmission PTO shaft, determining if the support rubber has been damaged, if the connecting component is loose, as well as whether the shaft of the agriculture transmission has been deformed. 3. Don't press the clutch pedal to the PTO shaft of the agricultural transmission and don't start at a high speed. 4. Overspeed and overload driving is strictly forbidden. 5. The agriculture transmission PTO shaft is to be filled regularly with grease. The lithium grease no. 3 should be filled during the summer, as well as the lithium grease no. 2 should be filled during the winter months. PTO Shaft Application Agricultural Gearboxes and PTO Shafts PTO shafts and agricultural gearboxes make great partners in the farming industry. They both transmit energy. Both the agricultural gearbox as well as PTO shaft are joined by two yokes on both sides. Based on the type of application they could be more or less torque ratings. This agriculture gearbox can be found through HZPT. Click here:https://hzpt.com/agricultural-pto-gearbox , / or contact us to get a quote! PTO Shaft Manufacturer Ever power , an engineering business that integrates the art of precision casting and precision forging and the machining. The company owns over 100 pieces of machinery such as turning, milling grinding, drawing, planing numerical control cast line, medium-frequency electric furnace friction press of 1000 tons, coating line, and so on. The company is the main producer of agriculture machinery, universal joint assemblies transmission shaft assembly agricultural machine transmission shaft Plow shaft, shaft assembly precise castings and die forgings and other items. The product range includes more than 100 variations of the 11 series, including the rotary cultivators, pulpers lawnmowers, field return machines and more. It produces an annual volume in excess of 120000 pieces of universal agricultural machinery joint assemblies, 4000 tonnes in precision casts as well as 4000 tonnes of die-forgings. The company is committed to the company's ethos of "people-oriented collaboration, unity, and excellence". The company adheres to the business principle that is "quality results, honest and trustworthiness, first for the customer". Establish the company's principle of "taking customer requirements as the primary goal" to provide courteous customer service. We look forward to working with old and new customers to develop together!

Minimum Order: 50

BTAM-Why choose to buy our oil press products? We are Benteng Machine,the leader of the oil press  and oil press line,if you have need,please contact us any time,we will guarantee the best quality and service with the lowest price. 1Q:Does your oil press save electricity? A:Our oil press is energy - saving. Our production models that 3-5kg/h,8- 12kg/h,50-75kg/h,100-200kg/h,200-250 , kg/h,250-350kg/h,300-400kg/h,350- 500kg/h,500-6 , 00kg/h,700-1000kg/h. Different types of oil have different power,the voltage is 380v, but we can also design it to 220v,440v, and can design as your requirement. 2Q:Is the oil press good to operate? Does it save manpower? A:Our oil press only needs one person to operate, simple and convenient, saving labor.We have home use oil press, single screw oil press、automatic combined oil press and hydraulic oil press. Either way, it saves manpower 3Q:Is the oil press productive? A:Sure, our oil press has high oil yield,and the residue oil is ＜ 6.5%. 4Q:Do your oil presses have quality and technical guarantee? Is there after- sale service after purchase? A:Yes, our quality is at the top level, and the oil press can have one year for warranty after sale , we have professional engineers ,can offer online support service at any time. 5Q:What is the difference between single oil press and automatic combined oil press? A:Single oil press is just only an oil press,automatic combined oil press is oil press with two vacuum oil filters,it is applied to the latest technology, can press crude oil and filtrate oil at the same time, youcan get the clean edible oil directly.Both the single oil press and automatic oil press can be used for various oilseeds with high oil yield,are very popularly among our clients.

Minimum Order: 1 bags

Contact Us I am Ivy from Henan Benteng Machine Co.,LTD in China, professional oil press manufacture in China , with more than 20 years experience. we specialize in producing screw oil press and automatic oil press,and hydraulic oil press and other auxiliary equipment,We are the leader of oil press and oil press line with full experience of more than 20 years, if you have need for the machine, please contact us any time. Our oil press can be used for various oilseed and has high oil yield rate . We guarantee to offer you the best quality and service with the most favorable price. There are also many news and industrial articles in our website. Our website:www.oilpresssite.com My whatsapp:+8615515395529 Email:ivy@bentengmachin , e.com

Minimum Order: 1 bags

PRODUCT DESCRIPTION high speed portable mini laser cutting machine cnc metal cutter machine 1530 CNC Sheet Metal Fiber Laser Cutting Machine 0 1530 CNC Sheet Metal Fiber Laser Cutting Machine 1 1. Fiber laser cutter power: 500W, 750W, 800W, 1000W, 1500W, 2000W, 3000W, 4000W, 6000w, 10000w, 12000w, etc. 2. Fiber laser generator: JPT, RAYCUS, MAX, NIGHT, IPG etc. 3. Fiber laser cutter materials: Iron, aluminum, carbon steel, stainless steel, copper, hardware and another metal sheet materials. 4. Other machine optional parts can be chosen, such as, rotary axis, exchange working table, full cover, etc. 5. China Top fiber laser machine cutting manufactuers, best price and high quality, with CE etc certificates. 1530 CNC Sheet Metal Fiber Laser Cutting Machine 2 Model 3015 Fiber Laser Cutting Machine Working Size 1500*3000mm Laser Power 1/1.5/2/3/4/6/8/12KW Laser Wavelength 1080nm Laser Beam quality <0.373mrad Working Life of Fiber Source More than 10,0000 hours Position Type Red Dot Pointer Cutting Thickness 0.5-10mm Within The range Max. Idle Running Speed 80-110M/min Max acceleration 1G Reorientation Accuracy Within ±0.01mm Lubrication System Electrical Motored Cooling mode Water cooling and protection system Machine power 9.3KW / 13KW /18.2KW /22.9KW Auxiliary Gas for Cutting Oxygen, Nitrogen, Compressed Air Compatible Software AutoCAD, CorelDraw, etc. Handle Control Wireless Control Handle Graphic Format DXF/PLT/AI/LXD/GBX/NC code Power Supply Voltage 220V 1Ph or 380V 3Ph, 50/60Hz Warranty 2 Years 1530 CNC Sheet Metal Fiber Laser Cutting Machine 3 Packing & Delivery 1530 CNC Sheet Metal Fiber Laser Cutting Machine 4 Company Profile 00:00 00:04 1530 CNC Sheet Metal Fiber Laser Cutting Machine 5 1530 CNC Sheet Metal Fiber Laser Cutting Machine 6 1530 CNC Sheet Metal Fiber Laser Cutting Machine 7 jining Gaochuang cnc equipment company integrates D&R ,manufacture,sales,service in one, specilized in produce: cantilever type portable cnc cutting machine(flame/ air plasmer) table type cnc cutting machine flame/air plasmer straighting-line cutting machine Gantry cnc cutting machine welding machine, CO2 welder, inverter welder etc , FAQ 1. who are we? We are based in Shandong, China, start from 2012,sell to Southeast Asia(30.00%),Africa(10.00%),Mid East(10.00%),South Asia(8.00%),Western Europe(7.00%),Central America(5.00%),Southern Europe(5.00%),Northern Europe(5.00%),South America(5.00%),North America(5.00%),Domestic Market(3.00%),Eastern Asia(3.00%),Eastern Europe(2.00%),Oceania(2.00%). There are total about 11-50 people in our office. 2. how can we guarantee quality? Always a pre-production sample before mass production; Always final Inspection before shipment; 3.what can you buy from us? cnc plasma cutting machine,cnc flame cutting machine,cnc air plasma cutting machine,gantry type cnc cutting machine,cnc table cutting machine 4. why should you buy from us not from other suppliers? We prefer to explain for price for a while Don't want to apologize for the quality for whole life we believe that only the perfect quality is our proud because we are GaoChuang CNC, numerical control cutting machine of professional manufacturers. 5. what services can we provide? Accepted Delivery Terms: FOB,CFR,CIF,EXW,CIP,DDP,DDU； Accepted Payment Currency:USD,EUR,CAD,AUD,HKD,GBP,CNY; Accep , ted Payment Type: T/T,L/C,Credit Card,PayPal,Western Union,Cash; Language Spoken:English,Chinese,Spanish,Japanese,Portug , uese,German,French,Russian,Korean,Ita lian

PRODUCT DESCRIPTION Doosan DX60 Used Hydraulic Crawler Excavator / Used Doosan Construction Machinery 0.2m3 Mode DX60 Rotation speed (rpm) 9.5 Walking speed (km/h) 4.1 / 3.0 Gradeability(%) 78/30 degrees Bucket Digging Force (kN) 44 Fuel tank (L) 115 Total length of transport (mm) 5850 Overall width for transportation (mm) 2000 Total length of track(mm) 2540 Minimum ground clearance (mm ) 400 Maximum excavation radius (mm) 6150 Maximum excavation height (mm) 5790 Maximum unloading height (mm) 4065 Maximum vertical excavation depth (mm) 3038 Bulldozer width × height (mm) 2000×350 Current Location Shanghai Shipping Within 3-5 working days after confiming purchase Good working condition Used Excavator Application Excavator a wide range of applications, by dress up a variety of auxiliary equipment, such as hydraulic hammers, hydraulic shears, bulldozing, grilled meats can complete crushing, demolition, capture and many other jobs. Used Doosan DX60 Excavator Details 6 Ton DX60 0.2m3 Second Hand Hydraulic Crawler Excavator With Doosan Bucket 06 Ton DX60 0.2m3 Second Hand Hydraulic Crawler Excavator With Doosan Bucket 16 Ton DX60 0.2m3 Second Hand Hydraulic Crawler Excavator With Doosan Bucket 26 Ton DX60 0.2m3 Second Hand Hydraulic Crawler Excavator With Doosan Bucket 36 Ton DX60 0.2m3 Second Hand Hydraulic Crawler Excavator With Doosan Bucket 46 Ton DX60 0.2m3 Second Hand Hydraulic Crawler Excavator With Doosan Bucket 5 After-sales Service Provided: Engineers available to service machinery overseas Our Service: Book hotel before visiting, pick you up in airport, guide you travel around Shanghai when you are free. More than 20 years experience to dealing with all types of used engineering machinery and shipment service all over the world. 3 Years warranty for engine and pump. Our Business: We are supplying various used constrction machines globally for users from different countries. Our machine stocks include excavators, bulldozers, wheel loaders, road rollers, motor graders, dumper trucks, forklifts and cranes,and we alwyas trying to provide machines with excellent quality and good prices. Also available: Hitachi: EX100, EX120, EX200, EX210, ZX200, ZX210, ZX230, ZX300, ZX360 Komatsu: PC100, PC120, PC200, PC220, PC300, PC360 Caterpillar: CAT320, CAT 330, CAT 345, CAT 336 volvo: EC210BLC, EC240BLC, EC360BLC, EC460BLC Also available: Hitachi: EX100, EX120, EX200, EX210, ZX200, ZX210, ZX230, ZX300, ZX360 Komatsu: PC100, PC120-6, PC200-5/-6/-7, PC220-6/-7/-8, PC300-5/-6/-7, PC360-7 Caterpillar: CAT320B/C/D, CAT 330B/C/D, CAT 345, CAT 336 volvo: EC210BLC, EC240BLC, EC360BLC, EC460BLC

In order to meet a variety of needs, we have 3 types of nursery seeding machines. They are KMR-80, KMR-78-2, and KMR-78. Of the three machine types, KMR-80 and KMR-78-2 are fully automatic, and KMR-78 is semi-automatic. All these machines’ power is electric and air compressor. And the air compressor mainly controls the two actions of hole punching and sowing.

Minimum Order: 1 bags

Construction Medium-Sized Concrete Mixer Machine Product Description Basic Info. Model NO. TCM-A 260-700L Vibrating Amplitude 1.0mm Certification CE Condi , tion New Color Yellow Drum 500L , Electric Power 6.5HP Speed of Mixing Drum 25-30r/Min Outline Diemension 204X106X123mm Gross Weight 344kgs 625L Mixer 625mm Diesel Power 7.5HP 750liter Mixer Drum 520mm Transport Package Carton Specification CE Tradem , ark G&G(Can put customer Logo. ) Origin China HS Code 847431000 Production Capacity 5000sets/Month Product Description Min.Order Quantity: 5 Set/Sets Supply Ability: 300 Set/Sets per Month Port: Qingdao Payment Terms: T/T Packaging & Delivery Packaging Details: 204x106x123cm in cartons Delivery Detail: 30-45days Specifications 260L /700L concrete mixer powerful electric motor CEapproved Model TCM-A TCM260-AM/AP/AD TCM350-AM/AP/AD TCM400-AM/AP/AD TCM500-AM/AP/AD TCM600-AM/AP/AD TCM700-AM/AP/AD Drum Capacity(L) 260 350 400 500 600 700 Power (ELEC/gas/diesel) 1500w/6.5hp/3.8hp 2200w/6.5hp/3.8hp 3000w/6.5hp/5.5hp 3000w/6.5hp/5.5hp 5500w/13hp/5.5hp 5500w/13hp/5.5hp Drum Diameter(mm) 760 760 900 900 950 1050 Drum Height(mm) 710 900 810 940 950 950 N.W/G.W.(kg) 255/270 270/285 280/295 310/325 326/346 405/420 20'GP/40'HQ(pcs) 14/28 14/28 14/28 24 40'HQ 24 40'HQ 22 40'HQ Construction Medium-Sized Concrete Mixer Machine Construction Medium-Sized Concrete Mixer Machine Construction Medium-Sized Concrete Mixer Machine Introduction: 1. The concrete mixer can be dragged to move by two wheels. 2. Cast iron ring gear enables steady and silent working. Features Adopting the design idea of high strength, high stiffness and high quality, we have designed streamline mixing drum, fully-enclosed frame and round handle, pedal type positioning and fixing structure of high speed, high efficiency and high reliability. With the application of German advanced quality managing mode, advanced equipment and technologies such as CNC laser cutting and punching press molding line, fully automatic acid pickling, phosphating, plastic spraying line etc, we have produced mixers of beautiful appearance, high stiffness , high quality and long service life. Application: It is applied in the mixing of concrete(such as construction, home repair), breeding feed(such as chicken farm, pig farm, fish farm, holothurians farm), chemical raw material(such as compost, industrial raw material), seed and solid or liquid with little viscosity. Operating Instruction 1. Check the machines before each operation 2. Please put the machine level and steady, and check the 4 legs fixed, and the bolt bars have been fixed tightly. We can make the machine according to your personal requirements This is our company's main product. This product has been selling well in Europe, North America, Australia and South America for more than ten years. We can adjust the details according to the different needs of our customers.