Coaxial Cables

Product Description 600/1000V Copper Conductor Underground XLPE Cable Steel Wire/Tape Armoured Power Cable Cable Selection It is essential that the type of cable ordered is suitable for its intended use. Cable choice will be based on a whole range of factors including installation specifications, relevant local regulations and the performance of appropriate cable types. It is therefore impossible to provide a conclusive guide to cable selection and we would advise you to contact us for our specialist advice on suitable designs to meet you specific cable needs. Cable structure Conductors Conductors shall be of Copper or Aluminium, circular standed(Non-compacted or Compacted) or Shaped, Class 1 or Class 2 to IEC 60228, BS EN 60228. For smaller sizes, a solid circular conductor, Class 1 as per IEC 60228, BS EN 60228 can also be supplied upon request. Insulation XLPE material and thickness shall be as per IEC 60502-1 or BS 5467 rated for 90° C continuous operation. PVC material and thickness shall be as per IEC 60502-1 or BS 6346. PVC insulation Material-PVC/A as per IEC 60502 or TI1 as per BS EN 50363. PVC insulation as per SASO 1694 rated for 85° C continuous operation is also available on request. Assembly Two, Three Four or Five insulated conductors are laid-up together with non- hygroscopic fillers compatible with the insulation material. Inner sheath The assembly is bedded with an extruded layer of PVC. In case of non- armoured cables, this layer may be omitted if the outer shape of the cable remains practically circular. Armour Galvanized Steel Wires applied helically over the bedding as per IEC 60502-1 or as per BS 5467, BS 6346. (Single core cables shall be Aluminium wire armoured)(SWA/AWA) Double Steel Tapes applied helically over the bedding of multi-core cables as per IEC 60502-1.(STA) Outer Sheath Outer sheath will be extruded PVC/ST2 as per IEC 60502-1, Type 9 as per BS 7655. Special type of PVC sheathing material such as fire retardant PVC, anti-termite and anti-rodent PVC, ultraviolet PVC, Oil resistant PVC, etc. Are available on request also other special sheathing materials such as LLDPE, MDPE, HDPE, LSF, CPE etc are available. Flame Performance of Cable Sheaths Cables can be supplied with special flame retardant PVC outer sheath to comply with the flame test requirements of IEC 60332-3-22, IEC 60332-3-23 and IEC 60332-3-24, can also supply cables with Low Smoke Halogen Free (LSHF) material according to IEC 60502-1, BS 7211, BS 6724 or other equivalent standards. Standard: IEC,BS,VDE,AS/NZS,ICEA,JIS and so on,designing and manufacturing special power cable according to the other standards required by the customer Type and Name: Type Designation Applications VV Copper conductor, PVC insulated, PVC sheathed power cable For laying indoors, in tunnel or cable trench, unable to bear external mechanical forces .Single core cable is not allowed to lay in a magnetic duct. VLV Aluminum conductor, PVC insulated, PVC sheathed power cable VY Copper conductor, PVC insulated, PE sheathed power cable VLY Aluminum conductor, PVC insulated, PE sheathed power cable VV22 Copper conductor, PVC insulated, steel tape armored, PVC sheathed power cable For laying indoors, in a tunnel in cable trench, or direct in ground, able to bear external mechanical forces. The single-core cable is not allowed to lay in the magnetic duct. VLV22 Aluminum conductor, PVC insulated, steel tape armored, PVC sheathed power cable VV23 Copper conductor, PVC insulated, steel tape armored, PE sheathed power cable VLV23 Aluminum conductor, PVC insulated, steel tape armored, PE sheathed power cable VV32 Copper conductor, PVC insulated, steel wire armored, PVC sheathed power cable For laying indoors, in tunnel cable trench, well or direct in ground, able to bear external mechanical forces and certain pulling force. VLV32 Aluminum conductor, PVC insulated, steel wire armored, PVC sheathed power cable VV33 Copper conductor, PVC insulated, steel wire armored, PE sheathed power cable VLV33 Aluminum conductor, PVC insulated, steel wire armored, PE sheathed power cable Type and Name: Type Designation Applications YJV Copper conductor, XLPE insulated, PVC sheathed power cable For laying indoors, in tunnel or cable trench, unable to bear external mechanical forces .Single core cable is not allowed to lay in a magnetic duct. YJLV Aluminum conductor,XLPE insulated, PVC sheathed power cable YJY Copper conductor, XLPE insulated, PE sheathed power cable YJJLY Aluminum conductor, XLPE insulated, PE sheathed power cable YJV22 Copper conductor,XLPE insulated, steel tape armored, PVC sheathed power cable For laying indoors, in a tunnel in cable trench, or direct in ground, able to bear external mechanical forces. The single-core cable is not allowed to lay in the magnetic duct. YJLV22 Aluminum conductor, XLPE insulated, steel tape armored, PVC sheathed power cable YJV23 Copper conductor, XLPE insulated, steel tape armored, PE sheathed power cable YJLV23 Aluminum conductor, XLPE insulated, steel tape armored, PE sheathed power cable YJV32 Copper conductor, XLPE insulated, steel wire armored, PVC sheathed power cable For laying indoors, in tunnel cable trench, well or direct in ground, able to bear external mechanical forces and certain pulling force. YJLV32 Aluminum conductor, XLPE insulated, steel wire armored, PVC sheathed power cable YJV33 Copper conductor, XLPE insulated, steel wire armored, PE sheathed power cable YJLV33 Aluminum conductor, XLPE insulated, steel wire armored, PE sheathed power cable

Description Springtek 400Gb/s QSFP-DD DR4 optical module designed for 500m optical communication applications. S-QD4A31M05-CD-4 module converts 8 channels of 50Gb/s (PAM4) electrical input data to 4 channels of parallel optical signals, each capable of 100Gb/s operation for an aggregate data rate of 400Gb/s. Reversely, on the receiver side, the module converts 4 channels of parallel optical signals of 100Gb/s each channel for an aggregate data rate of 400Gb/s into 8 channels of 50Gb/s (PAM4) electrical output data. An optical fiber cable with an MTP/MPO-12 connector can be plugged into the Springtek 400Gb/s QSFP-DD DR4 module receptacle.Proper alignment is ensured by the guide pins inside the receptacle.The cable usually cannot be twisted for proper channel to channel alignment.Electrical connection is achieved through an QSFP-DD MSA-compliant edge type connector. The product is designed with form factor, optical/electrical connection and digital diagnostic interface according to the QSFP-DD Multi-Source Agreement

UL10703 Single Conductor with extruded FRPE insulation, High Flexible, Halogen Free,80 ℃, 600V VW-1 Construction Conductor : stranded, tinned or bare copper. IEC60228 CL5 Insulation: FRPE Standards International: UL758 , UL1581, UL2556 RoHS,REACH Compliant, Technical data Rated voltage: 600 V Rated Temperature: -20~80℃ Flame: VW-1, FT1, FT2 Voltage withstand test:AC 2.5kV/1min Printing :E258652 UL10703 Single Conductor Industrial Electric Wire And Cable With Extruded FRPE Insulation 0 AWM STYLE 10703 AWGXX 80℃ 600V VW-1 ---c AWM I A/B 80℃ 600V FT1 -LF-HWATEK Note: Where "XX" means AWG No. Minimum bending radius flexing 10x cable Ø fixed installation 6x cable Ø Specifications Certificates UL, CUL, CE Packing and Shipping The cargo could be packaged as Hwatek’s standard requirement if client no special request, such as carton, wooden pallet or wooden case; If client put forward special packing requirements, Hwatek will specialize in custom materials and charge some fees; Hwatek’ll pack the cargo according to the transportation requirements strictly, including size, weight and safety; The cargo, manufacturer, packing details will be labeled on the outer packing; About transportation agent, Hwatek will give priority to customers' advice. If not, we can come up with some proposals and choose good and affordable agents for clients reference; Shipping term, It depends on the value of the goods and the will of the customer.

Laying method: 1. N2XY/NA2XY copper (aluminum) core cross-linked polyethylene is laid indoors, in channels and pipes, and can also be buried in loose soil, but cannot withstand pressure and mechanical external forces. 2. N2XBY/NA2XBY copper (aluminum) core XLPE insulated steel tape armored PVC sheathed power cables are laid underground and can withstand external mechanical forces, but cannot withstand large tensile forces. Application: N2XY low voltage electrical cable, that is, 0.6/1kv XLPE insulated and PVC sheathed power cable. This product is used for power transmission and distribution of power lines with a rated voltage of (U0/U) 0.6/1---26/35kv. The product standard is GB12706.3-91 Skills Requirement: 1. The maximum rated temperature of the cable conductor is 90°C. When a short circuit occurs (the longest duration does not exceed 5S), the maximum temperature of the cable conductor does not exceed 250°C. 2. The ambient temperature when laying the cable should not be lower than 0°C 3. Allowable bending radius during laying: single-core cable is not less than 15 times the outer diameter of the cable; multi-core cable is not less than 10 times the outer diameter of the cable.