Chemical Equipment & Lab Supplies

Introduction CY-SPC12-C spin coater is with vacuum chuck designed for easy and quick coating via sol-gel for wafers up to 12" diameter. This spin coater adopts advanced precision motor, the maximum speed can reach 5000rpm, which effectively guarantees the uniformity of film formation. Besides, the instrument adopts touch screen control, can preset the coating curve, which greatly simplifies the process. Application Liquid or colloidal materials can be coated on silicon wafers, crystals, quartz, ceramics and other substrates to form thin films, mainly used in photoresist spin coating, biological medium production, sol-gel method for polymer film production, etc. Technical parameters 1. Input power supply AC220V, 50Hz 2. Chamber material PP (transparent acrylic) 3. Substrate size Diameter≤12 inches (~300mm) 4. Spin speed 0-5000rpm 5. Acceleration 100-5000rpm/s 6. Speed resolution 1rpm 7. Single step time 3000s 8. Operation method 7 inches HD LCD touch screen 9. Dispensing method Manual dispensing 10. Coating curve Each curve has 5 segments, can store 5 curves in total 11. Vacuum chuck Yes, includes 12. Vacuum pump Oil-less pump 13. Pumping speed 50 L/min 14. Total weight ~40kg

Minimum Order: 1 bags

4-inch anti-corrosion heating spin coater This product is a spin coater or spin processor, which uses centrifugal force generated by high-speed rotation to coat film materials. This model adopts a special design, so that the substrate can be heated simultaneously during the spin coating process. The maximum heating temperature is 200℃, which can meet the temperature requirements of some solutions in the spin coating process. At the same time, the equipment is also equipped with a liquid drain pipe and a waste tank to facilitate customers to collect waste liquid and effectively prevent corrosive liquid from splashing into the environment. Technical parameters: Power supply AC220V, 50Hz Chamber material PTFE Upper cover PVC (Polyvinyl chloride, for observing the coating state conveniently) Sample stage Gold-plated copper plate, with good thermal conductivity Substrate size Diameter ≤ 4 inches (100mm) Heating mode Ceramic heating ring Operating temperature RT-200℃ Rotation speed 0-3000rpm Speed resolution 1rpm Operation Mode 7 inch HD LCD touch screen Glue dropping mode Manual glue dispensing, liquid can be supplied during spin coating Liquid drain pipe and waste liquid tank PTFE Spin coating curve Each curve has 5 segments, a total of 5 curves can be stored Vacuum chuck Gold-plated, 3 pieces with diameters of 10mm, 25mm, 55mm vacuum pump Oil-less pump Pumping speed 50 L/min

Minimum Order: 1 bags

4-inch anti-corrosion heating spin coater This product is a spin coater or spin processor, which uses centrifugal force generated by high-speed rotation to coat film materials. This model adopts a special design, so that the substrate can be heated simultaneously during the spin coating process. The maximum heating temperature is 200℃, which can meet the temperature requirements of some solutions in the spin coating process. At the same time, the equipment is also equipped with a liquid drain pipe and a waste tank to facilitate customers to collect waste liquid and effectively prevent corrosive liquid from splashing into the environment. Technical parameters: Power supply AC220V, 50Hz Chamber material PTFE Upper cover PVC (Polyvinyl chloride, for observing the coating state conveniently) Sample stage Gold-plated copper plate, with good thermal conductivity Substrate size Diameter ≤ 4 inches (100mm) Heating mode Ceramic heating ring Operating temperature RT-200℃ Rotation speed 0-3000rpm Speed resolution 1rpm Operation Mode 7 inch HD LCD touch screen Glue dropping mode Manual glue dispensing, liquid can be supplied during spin coating Liquid drain pipe and waste liquid tank PTFE Spin coating curve Each curve has 5 segments, a total of 5 curves can be stored Vacuum chuck Gold-plated, 3 pieces with diameters of 10mm, 25mm, 55mm vacuum pump Oil-less pump Pumping speed 50 L/min

Minimum Order: 1 bags

PTL-OV6P (Update from WPTL6-0.01) is a CE Certified Programmable Dip Coater (1-40 mm/min) designed to preparing multilayer coating up to 6 solutions inside a temperature controlled oven with touch-screen digital control. Dipping rate, pulling rate, dwell time, and amount of cycles can be setup by touch screen controller. It is designed for R&D Lab to prepare various optical or epitaxial films from liquid solution. 1. Controller 6" LCD color touch screen controller Working Voltage: 110-240V AC Max. Power Consumption: 50W 2. Liquid Holder Disk Can carry up to 6 liquid solutions Manually Rotate  Up to 6 layers of coating can be achieved by rotating liquid holder disk to dip samples from one solution to another 3. Beaker Six 150 ml beakers are included for immediate use Dimensions: 58mm(Dia) x 85mm(H) 4. Traveling Distance 0-80 mm Adjustable 5. Dipping/Pulling Speed 1-40 mm/min Programmable with accuracy within +/- 0.02% 6. Temperature Range 50-200°C (+/-1°C accuracy) 6. Dwell Time (in liquid) 0-999 seconds 7. Dry Time 0-999 seconds 8. Amount of Dipping 1-10 times at each position 9. Max. Amount of Cycles 50 times 10. Sample Holder Up to 6 samples can be carried sliding up and down through two guide rods 11. Oven Working Voltage: 208-240V AC (110V version is available via transformer) Max. Power Consumption: 600W Temperature:   50-200°C controlled by digital controller with +/- 1°C accuracy. Chamber Dimensions: 280mm(L) x 280mm(W) x 280mm(H) Inner Material: Stainless Steel Outside Dimensions: 406mm(L) x 406mm(W) x 610mm(H) 12. Product Dimensions  500mm(L) x 500mm(W) x 1180mm(H) 13. Compliance CE Certified 14. Warranty One year limited with lifetime support

Minimum Order: 1 bags

Product introduction: heat type tape casting technology is widely used in various high-temperature coating films, such as ceramic films, crystal films, battery material films, and special nano-films; it can adapt to the future development of film-forming science and technology under high temperature conditions. Main features: 1. Drying system with strong wind heating and digital display temperature control, the maximum working temperature is 200C; 2. The coating film speed is adjustable in the range of 0~100mm/sec, and has digital display; 3. Vacuum aluminum plate, available Quickly place or remove the substrate; 4. The stroke can be adjusted by the travel switch between 10~250mm; 5. With a doctor blade that adjusts the thickness of the coating film (accuracy 0.02mm) width 0-150mm;

Minimum Order: 1 bags

Roll to Roll film coating machine CY-AFC360R-HTUV This small automatic drying film coating machine is mainly used for coating liquid or colloidal film in the laboratory. The equipment uses a continuously variable motor to accurately control the coating film speed to achieve the purpose of advancing the scraper at a uniform speed for coating. The scraper adopts All stainless steel material has a constant weight, which can improve the consistency and uniformity of the coating film. The equipment adopts the bottom vacuum to absorb the sample, and has the bottom heating function, the heating temperature can reach up to 120℃, and the function of baking the film is realized during the film coating process, so that the film can be dried quickly. At the same time, the equipment is equipped with a winding and unwinding device, which can be used for continuous coating of copper foil or aluminum foil. The upper cover is equipped with an ultraviolet curing lamp, which can be used for curing and drying the film. This equipment is very suitable for continuous production of battery electrode materials. Technical parameters: 1. Input power AC220V, 60Hz 2. heating power 3000W 3. Total power 3100W 4. Coating vacuum chuck size 360mm x 200mm 5. Film thickness accuracy ±0.01mm 6. Film applicator 300 width 7. Rewinding and unwinding mechanism The speed of the rewinding and unwinding mechanism is adjustable from 1 to 400mm/min, and the mechanism adopts feedback adjustment, which can automatically correct the speed deviation 8. Heating temperature ≤120℃ 9. Top UV Wavelength 365nm 10. Temperature accuracy ±1℃ 11. Overall size 1245mm x 500mm x 270mm (close the protective cover) 1245mm x 550mm x 670mm (open the protective cover);Net weight About 100kg 12. Mechanical pump FY-4C-N;Pumping rate 4m3/h;Exhaust interface φ8 quick screw joint

Minimum Order: 1 bags

This model of roll to roll tape casting film coater is mainly used for coating liquid or colloidal film in laboratory. The equipment adopts step-less variable speed motor to precisely control the coating speed, so as to achieve the purpose of uniformly rotating the roller to drive the aluminum foil or copper foil for coating; the doctor-blade is made of all stainless steel, with constant weight, which can improve the consistency and uniformity of the coating; the coating platform is equipped with water cooling pipeline, which can be cooled by circulating water, so that the substrate and film material can be maintained at a low temperature;The rewinding and unwinding device adopts feedback adjustment, which can automatically control the speed within ± 1 rpm, effectively ensuring the uniformity of the coating film; the upper cover has the functions of dust prevention and heat preservation, and makes the equipment more beautiful. Technical parameter 1. Input power AC220V 50Hz 2. Total power 150W 3. Coating platform Material: aluminum Size: 500mm×300mm Embedded water cooling pipeline 4. Reel diameter ≤160mm 5. Film thickness accuracy ±0.01mm 6. Coating speed 0~100mm/s 7. Doctor blade 220mm wide 8. Overall dimensions 1180 mm × 300 mm × 310 mm (close protective cover) 9. Net weight About 100kg 10. Water cooling interface φ8 quick plug connector

Minimum Order: 1 bags

Ultrasonic pyrolysis sprayer The spray pyrolysis method is to spray the solution onto a heated base after atomization, and then obtain the desired material structure on the base. This material preparation method is particularly suitable for depositing oxides, and has a long history in the application of preparing transparent electrodes. Now this method is widely used in the preparation of perovskite-type solar cells. This equipment is an ultrasonic spray pyrolysis equipment independently researched and developed by our company. It is equipped with a 40KHz 130W ultrasonic atomizer, a PID temperature-controlled heating substrate, a high-precision peristaltic pump and a precision programmed stepping motor moving mechanism . Through the integrated design, this equipment can precisely control the parameters of the solution output, the spraying speed of the mist particles and the size of the mist particles. At the same time, the substrate temperature can also be controlled, which can meet your various test requirements.  Technical Parameters 1. Supply voltage AC220V，50Hz 2. Maximum power 3.5KW(Including compressor and peristaltic pump about 1.5KW) 3. Ultrasonic atomizer 40KHz 130W 4. Liquid viscosity 1-50mPa·s（cP） 5. Nozzle stroke X-Y axis up to 150mm 6. Moving speed 0-1000mm/min (X-axis)0-1000mm/min (Y-axis) 7. Heated substrate 150mm X 150mm 8. Maximum temperature 500℃ 9. Temperature control method AI-PID 10. Drip tank capacity 250mL 11. Peristaltic pump dispensing rate 0.006-41mL/min 12. Control method Touch screen 13. Overall size 680mm X 580mm X 1100mm

Minimum Order: 1 bags

Dual target magnetron sputter and thermal evaporation composite coating machine CY-MS500S-2TA1S magnetron sputter & thermal evaporation two-in-one coating machine can be used for the coating of electronic products, glass, ceramic samples, metal and other samples, especially suitable for sample preparation of laboratory SEM (scanning electron microscope). The equipment is mainly composed of stainless steel vacuum chamber, magnetron sputtering target, evaporation source, rotary heating sample table, vacuum pump unit, vacuum measurement gauge, air intake system and control system. Features a.Touch screen operation, temperature control meter detection. Digital parameter interface and automatic operation mode provide users with an excellent research and development platform; b.The vacuum chamber is made of 304 stainless steel with observation window and baffle. Beautiful shape, fine workmanship, excellent vacuum performance. The main sealing flange is CF series high vacuum sealing flange. Each interface of vacuum chamber is sealed with rubber seal ring, which has excellent vacuum performance and can effectively ensure the coating quality; c.The target is located at the bottom of the cavity, and the target is upward. The sample table has the function of heating and rotating, which can make the coating effect more uniform;; d.The vacuum acquisition system adopts two-stage vacuum pump group. The backing pump is mechanical pump with high pumping speed, which can effectively reduce the time from atmospheric pressure to low vacuum. The main pump is turbine molecular pump, which has high pumping speed and faster vacuum acquisition speed. The overall vacuum acquisition system is clean and fast. Technical parameter 1. Model CY-MS500S-2TA1S 2.New sample table is available Sample Size For Dia.150mm sample max. Height 70mm adjustable Rotation speed 1~20rpm Heating 0~500℃ 3. Magnetron sputter head,Quantity 2-inch ×2 Cooling mode Water cooled 4. Thermal evaporation evaporator source,Tungsten wire basket Max temp 1500℃,Thermocouple S type   5. Vacuum chamber Size 300mmDia.× 300mmH Watch window 100mm Dia. Material 304 SUS Open mode Front opening door 6. Vacuum system Mechanical pump Rotary vane pump Extraction interface KF16 Pumping 1.1L/s Molecular pump Turbo molecular pump Extraction interface CF150 Pumping 600L/s Exhaust interface KF40 Vacuum gauge Resistance gauge + ionization gauge Ultimate vacuum degree 1.3x10-4Pa Power supply AC;220V 50/60Hz 7. Sputter power supply DC power supply 1 set Output power ≤1000W Output voltage ≤600W Response time ＜5ms RF power supply 1 set Output power ≤1000W Power stability ≤5W RF frequency 13.56MHz RF stability ±0.005% 8. Film thickness gauge Resolution±0.03Hz,Accuracy ±0.5%,Upper range limit 50000 Speed 100~1000ms 9. Water cooled system Tank volume 9L Flow 10L/min 10. Gas system Flowmeter type MFC(mass flow meter),Range 200sccm,Gas type Ar 11. Other Input supply AC220V,50Hz Size 1400x750x1300mm Total power 4kw（host+vacuum pump） Weight 295kg

Minimum Order: 1 bags

Dual target magnetron sputter and thermal evaporation composite coating machine CY-MS500S-2TA1S magnetron sputter & thermal evaporation two-in-one coating machine can be used for the coating of electronic products, glass, ceramic samples, metal and other samples, especially suitable for sample preparation of laboratory SEM (scanning electron microscope). The equipment is mainly composed of stainless steel vacuum chamber, magnetron sputtering target, evaporation source, rotary heating sample table, vacuum pump unit, vacuum measurement gauge, air intake system and control system. Features a.Touch screen operation, temperature control meter detection. Digital parameter interface and automatic operation mode provide users with an excellent research and development platform; b.The vacuum chamber is made of 304 stainless steel with observation window and baffle. Beautiful shape, fine workmanship, excellent vacuum performance. The main sealing flange is CF series high vacuum sealing flange. Each interface of vacuum chamber is sealed with rubber seal ring, which has excellent vacuum performance and can effectively ensure the coating quality; c.The target is located at the bottom of the cavity, and the target is upward. The sample table has the function of heating and rotating, which can make the coating effect more uniform;; d.The vacuum acquisition system adopts two-stage vacuum pump group. The backing pump is mechanical pump with high pumping speed, which can effectively reduce the time from atmospheric pressure to low vacuum. The main pump is turbine molecular pump, which has high pumping speed and faster vacuum acquisition speed. The overall vacuum acquisition system is clean and fast. Technical parameter 1. Model CY-MS500S-2TA1S 2. Sample table Size150mm Dia.;Heating ≤500℃;Rotation speed 1-20r/min;Temp control ±1℃ 3. Magnetron sputter head,Quantity 2-inch ×2 Cooling mode Water cooled 4. Thermal evaporation evaporator source,Tungsten wire basket Max temp 1500℃,Thermocouple S type   5. Vacuum chamber Size 300mmDia.× 300mmH Watch window 100mm Dia. Material 304 SUS Open mode Front opening door 6. Vacuum system Mechanical pump Rotary vane pump Extraction interface KF16 Pumping 1.1L/s Molecular pump Turbo molecular pump Extraction interface CF150 Pumping 600L/s Exhaust interface KF40 Vacuum gauge Resistance gauge + ionization gauge Ultimate vacuum degree 1.3x10-4Pa Power supply AC;220V 50/60Hz 7. Sputter power supply DC power supply 1 set Output power ≤1000W Output voltage ≤600W Response time ＜5ms RF power supply 1 set Output power ≤1000W Power stability ≤5W RF frequency 13.56MHz RF stability ±0.005% 8. Film thickness gauge Resolution±0.03Hz,Accuracy ±0.5%,Upper range limit 50000 Speed 100~1000ms 9. Water cooled system Tank volume 9L Flow 10L/min 10. Gas system Flowmeter type MFC(mass flow meter),Range 200sccm,Gas type Ar 11. Other Input supply AC220V,50Hz Size 1400x750x1300mm Total power 4kw（host+vacuum pump） Weight 295kg

Minimum Order: 1 bags

Multi-function coating machine: Plasma Sputtering + Evaporating + Carbon Coating The multi-function coating machine can perform vacuum carbon evaporation, vacuum thermal evaporation and plasma sputtering. It can also perform a variety of ion treatments under the protection of high-purity argon. By changing the function kit, the device can quickly switch between multiple functions, which is very suitable for making SEM samples in the laboratory. This instrument is equipped with a mechanical pump and a molecular pump, which can meet a variety of vacuum requirements, especially high vacuum, and can effectively improve the quality of coating. Technical parameters: 1. Product model CY-PEC250G-HV 2. Vacuum chamber Bell jar: φ250x340mm 3. Evaporated glass isolation cover size: φ88x150mm with side opening hole 4. Plasma sputtering glass-plated isolation cover size: φ88x150mm 5. Intake system Equipped with manual fine-tuning valve, the interface is 1/4 inch ferrule connector 6. Power requirements AC 220V 50Hz 7. Plasma sputtering set Sputtering voltage 1600V Maximum current 50mA Target size 2 inches Working vacuum 10Pa~20Pa Working atmosphere Requires high purity argon 8. Thermal evaporation coating set Number of evaporation sources:2 Max. current 100A Working vacuum 10^-3Pa Working atmosphere Do not need any gas. Sample stage Diameter φ60mm, rotatable 9. Carbon evaporation set Evaporation method Carbon rod evaporation Max. current 160A Working vacuum 10^-3Pa Working atmosphere Do not need any gas. 10. Vacuum system Product model CY-GZK103-A Molecular pump Turbomolecular pump Backing pump Two-stage rotary vane pump Pumping rate Molecular pump: 600L/S Comprehensive pumping performance: 30 minutes vacuum can reach: 5×10E-3Pa Rotary vane pump: 1.1L/S Ultimate vacuum 5×10E-4Pa Pumping port KF40 Exhaust interface KF16 Vacuum measurement Compound vacuum gauge

Minimum Order: 1 bags

Multi-function coating machine: Plasma Sputtering + Evaporating + Carbon Coating The multi-function coating machine can perform vacuum carbon evaporation, vacuum thermal evaporation and plasma sputtering. It can also perform a variety of ion treatments under the protection of high-purity argon. By changing the function kit, the device can quickly switch between multiple functions, which is very suitable for making SEM samples in the laboratory. This instrument is equipped with a mechanical pump and a molecular pump, which can meet a variety of vacuum requirements, especially high vacuum, and can effectively improve the quality of coating. Technical parameters: 1. Product model CY-PEC250G-HV 2. Vacuum chamber Bell jar: φ250x340mm 3. Evaporated glass isolation cover size: φ88x150mm with side opening hole 4. Plasma sputtering glass-plated isolation cover size: φ88x150mm 5. Intake system Equipped with manual fine-tuning valve, the interface is 1/4 inch ferrule connector 6. Power requirements AC 220V 50Hz 7. Plasma sputtering set Sputtering voltage 1600V Maximum current 50mA Target size 2 inches Working vacuum 10Pa~20Pa Working atmosphere Requires high purity argon 8. Thermal evaporation coating set Number of evaporation sources:2 Max. current 100A Working vacuum 10^-3Pa Working atmosphere Do not need any gas. Sample stage Diameter φ60mm, rotatable 9. Carbon evaporation set Evaporation method Carbon rod evaporation Max. current 160A Working vacuum 10^-3Pa Working atmosphere Do not need any gas. 10. Vacuum system Product model CY-GZK103-A Molecular pump Turbomolecular pump Backing pump Two-stage rotary vane pump Pumping rate Molecular pump: 600L/S Comprehensive pumping performance: 30 minutes vacuum can reach: 5×10E-3Pa Rotary vane pump: 1.1L/S Ultimate vacuum 5×10E-4Pa Pumping port KF40 Exhaust interface KF16 Vacuum measurement Compound vacuum gauge

Minimum Order: 1 bags

Four source high vacuum evaporation coating equipment Model: CY-EVP325S-4S-T This equipment is a four-source high-vacuum evaporation coater. The equipment adopts a front-opening door vacuum chamber design. In addition, the chamber is increased to 500mm. The distance between the sample stage and the evaporation source has a larger adjustment range, which can adapt to various evaporation needs. It avoids the sample being damaged by the high temperature of the evaporation source. The chamber adopts an top sample stage, the sample stage can be rotated, heated and lifted, and all operations can be integrated and controlled through the touch screen. The equipment vacuum system is a two-stage vacuum system composed of a two- stage rotary vane pump and a turbo molecular pump, which can provide a clean and oil-free high vacuum environment. The equipment is equipped with a pneumatic valve system. Through the automatic control of the operating system, the user can perform operations such as one-button vacuum pumping, non-stop take out and place sample, and complete shutdown from the touch screen. The equipment is equipped with four sets of tungsten boat evaporation sources and water-cooled copper electrode. Each evaporation source supports a large current of 100A and a heating temperature of 1800℃. It can realize multi-layer coating or mixed coating of multiple materials. Technical parameters: 1. Sample stage Size Maximum support φ150mm samples Height Adjustable up and down 140mm 2. Evaporation source Quantity Tungsten Boat x4 3. Vacuum chamber Chamber size φ325mm x 510mm Observation window Front φ100mm with shading plate Chamber material 304 stainless steel Open method Front door opening 4. Film thickness control Crystal oscillator type film thickness measuring instrument, optional multi-channel film thickness controller 5. Vacuum system Backing pump Two stage rotary vane pump Pumping port KF16 Secondary pump Turbomolecular pump Pumping port CF160 Vacuum measurement Resistance + ionization Compound vacuum gauge Exhaust rate Mechanical pump 1.1L/s Ultimate vacuum 1.0E-5Pa Power supply Molecular pump 600L/s 6. Control system PLC automatic control 7. Operation interface: touch screen + operation panel 8. Others Supply voltage AC220V,50Hz Overall size 1000mm x 800mm x 1500mm Total power 10kW Total Weight 350kg

Minimum Order: 1 bags

Four source high vacuum evaporation coating equipment Model: CY-EVP325S-4S-T This equipment is a four-source high-vacuum evaporation coater. The equipment adopts a front-opening door vacuum chamber design. In addition, the chamber is increased to 500mm. The distance between the sample stage and the evaporation source has a larger adjustment range, which can adapt to various evaporation needs. It avoids the sample being damaged by the high temperature of the evaporation source. The chamber adopts an top sample stage, the sample stage can be rotated, heated and lifted, and all operations can be integrated and controlled through the touch screen. The equipment vacuum system is a two-stage vacuum system composed of a two- stage rotary vane pump and a turbo molecular pump, which can provide a clean and oil-free high vacuum environment. The equipment is equipped with a pneumatic valve system. Through the automatic control of the operating system, the user can perform operations such as one-button vacuum pumping, non-stop take out and place sample, and complete shutdown from the touch screen. The equipment is equipped with four sets of tungsten boat evaporation sources and water-cooled copper electrode. Each evaporation source supports a large current of 100A and a heating temperature of 1800℃. It can realize multi-layer coating or mixed coating of multiple materials. Technical parameters: 1. Sample stage Size Maximum support φ150mm samples Height Adjustable up and down 140mm 2. Evaporation source Quantity Tungsten Boat x4 3. Vacuum chamber Chamber size φ325mm x 510mm Observation window Front φ100mm with shading plate Chamber material 304 stainless steel Open method Front door opening 4. Film thickness control Crystal oscillator type film thickness measuring instrument, optional multi-channel film thickness controller 5. Vacuum system Backing pump Two stage rotary vane pump Pumping port KF16 Secondary pump Turbomolecular pump Pumping port CF160 Vacuum measurement Resistance + ionization Compound vacuum gauge Exhaust rate Mechanical pump 1.1L/s Ultimate vacuum 1.0E-5Pa Power supply Molecular pump 600L/s 6. Control system PLC automatic control 7. Operation interface: touch screen + operation panel 8. Others Supply voltage AC220V,50Hz Overall size 1000mm x 800mm x 1500mm Total power 10kW Total Weight 350kg

Minimum Order: 1 bags