Chemicals & Plastics - Others

(1) High precision, high efficiency, and high gain. The most important job of using SMC/BMC for the manufacture of antennas is to fully exploit its features and achieve high precision in antenna design from product design and process. Under the condition that the shrinkage ratio of the material and the SMC / BMC molding shrinkage rate have been considered in the mold size design, the SMC/BMC reflector surface has a smaller shape from the original design paraboloid after molding. That is, the accuracy of the SMC/BMC molded antenna is completely guaranteed by the accuracy of the mold. The rms value of the SMC/BMC antenna molded integral reflection surface is 0.25 mm, and the rms value of the single-piece reflection surface of the split antenna is less than 0.3 mm, and the rms value of the reflective surface after assembly is less than 0.6 mm. (2) Corrosion resistance Conventional antenna materials such as aluminum plates and steel plates are made of metal materials, not as good as SMC/BMC which as a non-metal dielectric composite material in terms of acid resistance, alkali, salt, and corrosion resistance. The Pikington laboratory in the United States used infrared to analyze the surface of SMC/BMCmaterials and found that its surface is covered by additives, resin, and very fine calcium acid filler. It has good acid resistance, water resistance and corrosion resistance. The antenna reflection made by this material is solved the disadvantage of the traditional metal material antenna is easy to corrode. In coastal areas, rainy, humid areas and areas with excessive acid rain, the anti-corrosion advantages of SMC molded antennas are particularly prominent. The SMC/BMC molded antenna samples were placed in 130 highly corrosive chemical environments at an ambient temperature of 50 ° C. The results showed that the test samples showed little or no change. (3) Long life The average aluminum plate antenna is as small as 2-3 years in the coastal area, and more often 4-6 years, and it will generally be damaged by salt spray erosion and aging. The most obvious example is the cable TV (CATV) in Taiwan, which was built earlier than the mainland. It is estimated that there are nearly 1000 satellite TV receiving antennas on the island, all built in the mid-1980s, all of which were aluminum plate antennas, until the early 1990s. , that is, has begun to replace. The service life of SMC molded antennas is generally more than 15 years; PROMLIN's prototype SMC molded antennas in 1985 are still working normally, and they are subject to typhoons and heavy rain every year. (4) Strong wind resistance Since the antenna reflection surface is designed during the molding process, multiple longitudinal and circumferential rib structures are designed. According to the structural strength calculation, the SMC antenna can withstand a wind load of 45 m/s, which shows its remarkable structural rigidity and strength. (5) Special reflective layer technology The reflective surface of the SMC antenna uses a metal aluminum mesh as a reflective layer of electromagnetic waves. The aluminum mesh in the finished antenna is evenly embedded under the surface SMC, which can reflect electromagnetic waves and insulate the atmosphere, and plays a good protective role. (6) Good consistency, no deformation, easy to transport and install Because SMC antenna adopts membrane pressure technology under high temperature and high pressure. Its material properties and processing technology determine the unparalleled consistency of SMC antennas with other antennas. This not only ensures the accuracy and high gain of the antenna, but also is very easy to install and debug. SMC, commonly known as "glass reinforced plastic", has the characteristics of no deformation, which eliminates the adverse effects of antenna deformation on the satellite receiving system during transportation. SMC and BMC composite require heating rather than cooling systems. The temperature of the mold is usually between 130 and 160. It is very important to keep the temperature of the mold and the exhaust gas when designing the mold. The mold is easier to fill, the product is not easy to be deformed, and the surface is better. Commonly used heating systems are steam, oil and electric heating rods. Vacuum assisted systems for BMC and SMC molds: Products with Class A surfaces are usually vacuum-assisted, and the internal cavity and vacuum insulation of the mold are very important. The mold must have a sensor and a vacuum system to measure the mold temperature and pressure vacuum. Production SMC and BMC molding: must guarantee high quality, long life and economy. Aobang Technology Co., Ltd.'s years of experience in the production of SMC and BMC molds and proficiency in machine, mold, material and process can ensure the maximum benefit of customers.

Minimum Order: 1 bags

High-strength, wear-resistant, fire-resistant, color BMC material for medium and low voltage insulators such as SMC Insulation, bmc insulation. Typical applications are switch boards, busbars, switchgear, etc. BMC (Body Molding Plastics) is a blend of glass fiber reinforced polyester resin and chemical mineral materials with special properties such as electrical insulation, low density, high mechanical strength and fire resistance. High sealing, high safety, low process and low cost. Established in 2010 and located in Chengnan Development Zone, Luoshe Town, Huzhou City, Zhejiang Province, Zhejiang Aobang Technology Co., Ltd. has extensive bulk molding compound process and many refined testing laboratories as a spinal column in the industry. Whether at home or abroad, Zhejiang Aobang Technology Co., Ltd. can manufacture top quality composite molds with advanced mold making concept, proprietary application technology and production technology. By the way, being a high-tech enterprise, it is a fact that this company enjoys a good fame in the new motor and energy automobile industry in Hangzhou. SMC and BMC composite require heating rather than cooling systems. The temperature of the mold is usually between 130 and 160. It is very important to keep the temperature of the mold and the exhaust gas when designing the mold. The mold is easier to fill, the product is not easy to be deformed, and the surface is better. Commonly used heating systems are steam, oil and electric heating rods. Vacuum assisted systems for BMC and SMC molds: Products with Class A surfaces are usually vacuum-assisted, and the internal cavity and vacuum insulation of the mold are very important. The mold must have a sensor and a vacuum system to measure the mold temperature and pressure vacuum. Production SMC and BMC molds must guarantee high quality, long life and economy. Aobang Technology Co., Ltd.'s years of experience in the production of SMC and BMC molds and proficiency in machine, mold, material and process can ensure the maximum benefit of customers.

Minimum Order: 1 bags

Aobang composite Wall Panel is divided into: BMC Wall Panel, SMC Panel, GRP Wall , GFK Wall Panel. Composite Wall Panel the main functions: use imported silver ion, special effect antibacterial; energy saving; anti-corrosion, waterproof and moisture proof, mildewproof, fireproof; no harmful substances, no formaldehyde; easy to clean and maintain; scratch resistant; can be repeatedly disassembled, easy to repair; low carbon Environmental protection, surface diffuse reflection and energy saving; can be recycled, the economical applicability of building materials, high cost performance; beautiful appearance. Established in 2010 and located in Chengnan Development Zone, Luoshe Town, Huzhou City, Zhejiang Province, Zhejiang Aobang Technology Co., Ltd. has extensive bulk molding compound process and many refined testing laboratories as a spinal column in the industry. Whether at home or abroad, Zhejiang Aobang Technology Co., Ltd. can manufacture top quality bmc compound molds with advanced mold making concept, proprietary application technology and production technology. By the way, being a high-tech enterprise, it is a fact that this company enjoys a good fame in the new motor and energy automobile industry in Hangzhou. SMC and BMC composite require heating rather than cooling systems. The temperature of the mold is usually between 130 and 160. It is very important to keep the temperature of the mold and the exhaust gas when designing the mold. The mold is easier to fill, the product is not easy to be deformed, and the surface is better. Commonly used heating systems are steam, oil and electric heating rods. Vacuum assisted systems for BMC and SMC molds: Products with Class A surfaces are usually vacuum-assisted, and the internal cavity and vacuum insulation of the mold are very important. The mold must have a sensor and a vacuum system to measure the mold temperature and pressure vacuum. Production SMC and BMC molds must guarantee high quality, long life and economy. Aobang Technology Co., Ltd.'s years of experience in the production of SMC and BMC molds and proficiency in machine, mold, material and process can ensure the maximum benefit of customers.

Minimum Order: 1 bags

What is gfk material? Aobang composite roofing tiles is divided into: BMC roofing tiles, SMC roofing tiles, GRP roof tiles, GFK roofing tiles. Due to the excellent properties of BMC, SMC, GRP, GFK materials, it is the best choice for making roof tiles. BMC, SMC, GRP, GFK material is a composite material, mixed with polyester resin, chemical and mineral fillers, technical agents, usually reinforced with GFK fiberglass. It is an excellent material GFK for outdoor applications. It has weather resistance and UV stability and has a service life of more than 30 years in outdoor environments. It absorbs almost no moisture, so it can isolate the moisture from the outdoors to the room. It is water and chemical resistant so acid rain does not affect the surface of the roof. Colors are easily mixed into the BMC, SMC, GRP, GFK material as a pigment, so colored tiles can be easily obtained and the color does not disappear during its lifetime. BMC, SMC, GRP, GFK materials are also fire resistant. If there is no source of burning material around it, it will not spread and will immediately go out. Light weight and high strength are one of the biggest advantages of BMC, SMC, GRP, GFK materials. As the grp roof supplies, this grp roofing materials has a density of 1.7-2.0. It makes the tiles very light. Transportation costs, installation costs, etc. can be reduced. this materials make your roof tiles more colorful, longer lasting and more cost effective. Advantage: Light weight, high strength, aging resistance, UV protection, acid and alkali resistance, waterproof and moisture proof, no fading, low thermal conductivity and energy saving. Established in 2010 and located in Chengnan Development Zone, Luoshe Town, Huzhou City, Zhejiang Province, Zhejiang Aobang Technology Co., Ltd. has extensive bulk molding compound process and many refined testing laboratories as a spinal column in the industry. Whether at home or abroad, Zhejiang Aobang Technology Co., Ltd. can manufacture top quality composite molds with advanced mold making concept, proprietary application technology and production technology. By the way, being a high-tech enterprise, it is a fact that this company enjoys a good fame in the new motor and energy automobile industry in Hangzhou. SMC and BMC composite require heating rather than cooling systems. The temperature of the mold is usually between 130 and 160. It is very important to keep the temperature of the mold and the exhaust gas when designing the mold. The mold is easier to fill, the product is not easy to be deformed, and the surface is better. Commonly used heating systems are steam, oil and electric heating rods. Vacuum assisted systems for BMC and SMC molds: Products with Class A surfaces are usually vacuum-assisted, and the internal cavity and vacuum insulation of the mold are very important. The mold must have a sensor and a vacuum system to measure the mold temperature and pressure vacuum. Production SMC and BMC molds must guarantee high quality, long life and economy. Aobang Technology Co., Ltd.'s years of experience in the production of SMC and BMC molds and proficiency in machine, mold, material and process can ensure the maximum benefit of customers.

Minimum Order: 1 bags

Aobang composite ceiling is divided into: BMC ceiling, SMC ceiling, GRP ceiling, GFK Ceiling. The ceiling materials have been developed for more than ten years, and the technology is constantly being updated. The PVC ceiling is not resistant to high temperature, and it is easy to deform in a hot environment. The plastic steel plate is improved from the second generation of ceiling material PVC, which has the advantages of lower price, good thermal insulation and sound insulation, rich color and easy making and installation. However, according to the supervision and inspection results of the plastic sheet market by the Supervisory Office, the quality pass rate of plastic steel products on the market is only 40%, and the phenomenon of “water injection” in bending strength, coating thickness and alkali resistance is serious. Moreover, the plastic steel sheet has low strength, is easily twisted, is not environmentally friendly, has poor weather resistance, and releases toxic gases when burned. The physical properties of the composite material aggregate ceiling are very stable, and will not be deformed even if the water is long time. The composite ceiling is an excellent material for the ceiling and naturalization board in terms of strength and rigidity. The ceiling uses BMC,SMC,GRP,GFK bulk molding compound as a completely environmentally friendly material, and its advantages are numerous, as follows: Beautiful, moisture-proof, easy to clean, excellent flame retardant effect, high strength, long life, high environmental protection, easy installation, moisture-proof and waterproof, heat insulation, corrosion resistance, tight connection, oxidation resistance, anti-aging, no deformation, high strength, Light and tough, with natural texture and wooden texture, a variety of colors, natural and beautiful, with a variety of specifications, size, shape, thickness, the same processing properties as logs, no pollution, recycling, no cracks, no expansion, no deformation, no maintenance, no mold, anti-corrosion, anti-insect, anti-termite, energy saving. What is important is the low material cost of BMC,SMC,GRP,GFK molding compound, making it a cost-effective ceiling material than such as steel-plastic panels, aluminum gussets, and aluminum alloys. The visual effect is soft, feels good, high strength, flame retardant, fireproof, and has strong weather resistance. Excellent insulation and heat insulation performance, which overcomes the poor thermal insulation performance of traditional ceilings. Good water resistance, no corrosion, no deformation, no fading and no other undesirable phenomena in a humid environment. Excellent sound absorption, it is a good sound insulation material, suitable for public places such as medium and high-grade office buildings and large conference halls. Established in 2010 and located in Chengnan Development Zone, Luoshe Town, Huzhou City, Zhejiang Province, Zhejiang Aobang Technology Co., Ltd. has extensive bulk molding compound process and many refined testing laboratories as a spinal column in the industry. Whether at home or abroad, Zhejiang Aobang Technology Co., Ltd. can manufacture top quality composite molds with advanced mold making concept, proprietary application technology and production technology. By the way, being a high-tech enterprise, it is a fact that this company enjoys a good fame in the new motor and energy automobile industry in Hangzhou. SMC and BMC composite require heating rather than cooling systems. The temperature of the mold is usually between 130 and 160. It is very important to keep the temperature of the mold and the exhaust gas when designing the mold. The mold is easier to fill, the product is not easy to be deformed, and the surface is better. Commonly used heating systems are steam, oil and electric heating rods. Vacuum assisted systems for BMC and SMC molds: Products with Class A surfaces are usually vacuum-assisted, and the internal cavity and vacuum insulation of the mold are very important. The mold must have a sensor and a vacuum system to measure the mold temperature and pressure vacuum. Production SMC and BMC molds must guarantee high quality, long life and economy. Aobang Technology Co., Ltd.'s years of experience in the production of SMC and BMC molds and proficiency in machine, mold, material and process can ensure the maximum benefit of customers.

Minimum Order: 1 bags

Aobang composite Building Decoration materialis divided into: BMC building decoration material, SMC building decoration material, GRP building decoration material, GFK building decoration material. Building decoration materials may have heard of commonly used bmc materials such as sandstone and cement. BMC, SMC, GRP, and GFK composite materials have been heard by few people. It is a new type of material. What are the advantages? 1. Short molding cycle, can be molded or injected, suitable for mass production. 2. A large amount of filler can be added to meet the requirements of flame retardancy and dimensional stability, and the cost is low. 3. Complex products can be integrally formed, and inserts, holes, tables, ribs, grooves, etc. can be molded at the same time. 4. Compared with ordinary thermoplastics, the heat resistance, insulation and modulus of elasticity of the products are higher. 5. The skills of workers are not high, and it is easy to automate and save labor. 6. The size of the product is accurate. 7. The working environment is good. It can be known that it is resistant to water and oil and excellent corrosion resistance, and its heat resistance and good electrical properties are its advantages, making it stand out in the highly competitive material market. In addition, it can be further found that the composite material has higher requirements for the post-use environment than other materials. We can provide GRP building products for you. SMC and BMC composite require heating rather than cooling systems. The temperature of the mold is usually between 130 and 160. It is very important to keep the temperature of the mold and the exhaust gas when designing the mold. The mold is easier to fill, the product is not easy to be deformed, and the surface is better. Commonly used heating systems are steam, oil and electric heating rods. Vacuum assisted systems for SMC and BMC molding: Products with Class A surfaces are usually vacuum-assisted, and the internal cavity and vacuum insulation of the mold are very important. The mold must have a sensor and a vacuum system to measure the mold temperature and pressure vacuum. Production SMC and BMC molds must guarantee high quality, long life and economy. Aobang Technology Co., Ltd.'s years of experience in the production of SMC and BMC molds and proficiency in machine, mold, material and process can ensure the maximum benefit of customers.

Minimum Order: 1 bags

CRYSCORE can offer Epi-Ready grade sapphire wafer with a very low surface roughness in complete orientation options. C-plane(0001) sapphire wafers are being extensively used for epitaxial growth of III-V and II-VI compounds, such as gallium nitride (GaN), aluminum nitride (AlN), for bright blue and green LED and laser diodes. Technical Applications of Standard Sapphire Wafers C-plane sapphire wafers are widely used to grow III-V and II-VI deposited films of wide band-gap nitride and oxide semiconductor materials such as gallium nitride (GaN), aluminum nitride (AlN), indium nitride (InN), zinc oxide (ZnO ultraviolet light emission) and tin oxide (SnO2 ultraviolet luminescent material), etc. In addition, standard C-plane(0001) sapphire wafers are widely applied to fabricate LED white and blue light, ultraviolet and deep UV LED epitaxial wafers by Metal-Organic Vapor Deposition(MOCVD), Molecular Beam Epitaxy (MBE), Plasma Enhanced Chemical Vapor Deposition(PECVD) and other epitaxy growth methods. CRYSCORE standard sapphire wafers also are used as the substrates of heterojunction bipolar transistor (HBT), a laser diode (LD), UV detector, nanotube, and the heat dissipation material of high temperature and high power high-frequency electronic device. Competitive Advantages of CRYSCORE's Sapphire Wafers 99.999 % high purity single crystal Al2O3 material. Special CMP (Chemical Mechanical Polishing) technology to ensure its performance at a low cost. Excellent surface quality in all orientations (less than 0.2 nm for C-plane, less than 0.5 nm for A-plane, M-plane, R-plane, N-plane, V-plane, 10-14, etc.) Cleaned in class 100 cleanroom by ultrapure water with quality above 18MΩ *cm. 25 pcs a pack or single pack is available to maximize customer flexibility in their research. Traceable product serial number. Compact carton packaging for safer shipping and cost-saving. Standard wafers are Generally in stock to ensure a quick delivery. As a professional sapphire wafer supplier, CRYSCORE aims to provide customers with the best products and services, and let our technology benefits the world. We provide sapphire substrates,c plane sapphire substrate,c plane sapphire and Al2O3 substrate,RFQ today.

Minimum Order: 1 bags

Sapphire has a wide transmission range, spanning the three wavelength bands of ultraviolet, visible light and infrared and has high thermal shock resistance, high hardness and wear resistance. Almost no substance except the diamond can produce scratches on its surface, and its chemical properties are stable which is insoluble in most acid solutions. Furthermore, because of its high strength, windows made of sapphire are thinner. A high grade of sapphire would have little or no light scatter or lattice distortion and be used mainly for the most demanding optical applications. CRSYCORE is a professional sapphire windows supplier who uses optical grade one single crystal material to ensure its high quality. Our sapphire optical windows have been polished to surface quality of 10/5 scratch-dig, and the surface roughness is lower than 0.2 nm (for C-plane). Both coated and uncoated sapphire windows can be provided. Besides, we supply custom sapphire windows with any size and thickness in complete orientations. If you want to buy sapphire substrates and Sapphire wafer,you can find us.

Minimum Order: 1 bags

Due to the less mismatched lattice and stable chemical and physical properties, sapphire(Al2O3) wafer is the popular substrates for III-V nitrides, superconductor and magnetic epi-film. They are widely used in GaN and thin-film epitaxial growth, silicon on sapphire, LED market and optics industry. CRYSCORE is a professional sapphire wafer supplier who manufactures 99.999% high purity single crystal polished sapphire wafers for epitaxy. And our sapphire (Al2O3) substrates feature excellent surface finish, which is the key LED parameter. If you are looking for reliable sapphire wafer suppliers, contact us now. We are one of the professional sapphire substrate suppliers,sapphire wafer manufacturers and sapphire wafer suppliers.As sapphire wafer supplier and sapphire wafer manufacturer,we provide polished sapphire substrates,sapphire rod,sapphire substrate and c plane sapphire wafers,contact us now.

Minimum Order: 1 bags

Sapphire ingots are typically used as raw materials for further processing. These sapphire rods and sapphire ingots are uniformly shaped, usually as cylinders. The most sapphire crystal grows in A-axis, and the most widely used sapphire substrate in the LED market is its C-plane (0001). Therefore, it is necessary to drill the c-plane sapphire ingot from the side of the crystal. CRYSCORE provides sapphire rods and ingots with ground surfaces for further processing and polishing. They are cored from high-grade Kyropoulos grown boules. We supply dia. 2-inch to 8-inch sapphire rod and ingot with any orientation and custom specifications. Flats are available upon request. Specifications of Sapphire Ingots/Rods Item Sapphire Ingots Crystal Materials 99,999%, High Purity, Monocrystalline Al2O3 Orientation C-plane(0001), A-plane(11-20), M-plane(10-10), R-plane(1-102), N-plane(11-23), V-plane(22-43) Diameter 2-inch, 4-inch, 6-inch, 8-inch, etc. Flat Upon request Surface Finish Fine Ground Packaging Single piece packaging We are one of the perfect sapphire ingot manufacturers,we provide sapphire substrate and sapphire ingot,please feel free to contact us.

Minimum Order: 1 bags

R plane(1-102) sapphire wafers are preferred for the hetero-epitaxial deposition of silicon used in microelectronic IC applications. R plane is the non-polar plane of sapphire. So the different positions of R-plane in sapphire devices, the mechanical, thermal, electrical and optical properties of sapphire devices will vary greatly, which will also affect the subsequent processing performance, processing efficiency and processing yield of sapphire devices. In order to make the crystal structure of sapphire ingot and subsequent sapphire products consistent, the more common method is to process an A- direction surface on the sapphire ingot as the flat orientation of sapphire wafer (subsequent sapphire products), so that the R-direction position of sapphire ingot and the wafer is consistent. Specifications of R-Plane (1-102) Sapphire Wafers Item 2 -inch R-plane(1-102) 430μm Sapphire Wafers Crystal Materials 99,999%, High Purity, Monocrystalline Al2O3 Grade Prime, Epi-Ready Surface Orientation R-plane(1-102) Diameter 50.8 mm +/- 0.1 mm Thickness 430 μm +/- 25 μm Primary Flat Orientation 45 +/- 1deg. counter-clockwise from C-axis projection on R-plane Primary Flat Length 16.0 mm +/- 1.0 mm Single Side Polished Front Surface Epi-polished, Ra < 0.5 nm (by AFM) (SSP) Back Surface Fine ground, Ra = 0.8 μm to 1.2 μm Double Side Polished Front Surface Epi-polished, Ra < 0.5 nm (by AFM) (DSP) Back Surface Epi-polished, Ra < 0.5 nm (by AFM) TTV < 10 μm BOW < 10 μm WARP < 10 μm Cleaning / Packaging Class 100 cleanroom cleaning and vacuum packaging, 25 pieces in one cassette packaging or single piece packaging. Note: Custom sapphire wafers with any orientation and any thickness can be provided. We have sapphire substrates,r plane sapphire and Sapphire Windows,RFQ today.

Minimum Order: 1 bags

Sapphire wafer is the most widely used substrate material in semiconductor lighting industry, and patterned sapphire substrate (PSS) is the general method to improve the luminous efficiency of semiconductor lighting devices. These sapphire substrates are with periodic structures of various shapes such as cone, dome, pyramid, and pillar, etc. Cryscore's Excellent Patterned Sapphire Substrates Pattern dimension, aspect ratio, and uniformity across the wafer as well as consistency from wafer to wafer, are important factors to improve the light extraction. Currently, we provide 2-inch and 4-inch patterned sapphire substrates (PSS sapphire and wafer) with the following specifications. Diameter: 2.7 +/- 0.1 μm. Spacing: 0.3 +/- 0.1 μm. Depth: 1.7 +/- 0.15 μm. We are one of the best sapphire substrate manufacturers,we provide sapphire substrate,pss wafer,pss sapphire,patterned sapphire substrates,patterned sapphire substrate and Sapphire substrate,contact us now.

Minimum Order: 1 bags

Due to its application prospects in solar-blind ultraviolet detection, MgZnO alloy semiconductor films with suitable band gaps have attracted more and more attention. A series of MgxZn1-xO thin films with different compositions were prepared on M plane sapphire wafers by using low-pressure metalorganic chemical vapor deposition (LP-MOCVD). CRYSCORE provides M plane (10-10) sapphire wafers with excellent surface quality. The roughness on the epi-polished side is lower than 0.5 nm. Specifications of M-Plane (10-10) Sapphire Wafers Item 2-inch M-plane(10-10) 430μm Sapphire Wafers Crystal Materials 99,999%, High Purity, Monocrystalline Al2O3 Grade Prime, Epi-Ready Surface Orientation M-plane(11-10) Diameter 50.8 mm +/- 0.1 mm Thickness 430 μm +/- 25 μm Primary Flat Orientation C-plane(0001) +/- 0.2° Primary Flat Length 16.0 mm +/- 1.0 mm Single Side Polished (SSP) Front Surface Epi-polished, Ra < 0.5 nm (by AFM) Back Surface Fine ground, Ra = 0.8 μm to 1.2 μm Double Side Polished (DSP) Front Surface Epi-polished, Ra < 0.5 nm (by AFM) Back Surface Epi-polished, Ra < 0.5 nm (by AFM) TTV < 10 μm BOW < 10 μm WARP < 10 μm Cleaning / Packaging Class 100 cleanroom cleaning and vacuum packaging, 25 pieces in one cassette packaging or single piece packaging. Note: Custom sapphire wafers with any orientation and any thickness can be provided. Our sapphire wafer cost you less and help you to achieve more, contact us to get more information. We have sapphire substrates,sapphire m plane and Patterned sapphire substrate,RFQ today.

Minimum Order: 1 bags

Due to the extensive applications of sapphire in various fields, different dimensions are required. CRYSCORE can provide custom sapphire windows with any size and thickness in complete orientations. All of these windows are available with high-precision polished surface, surface accuracy and parallelism. For custom sapphire windows, we also offer various services, such as anti- reflection coatings or laser processing. We can provide custom sapphire windows with laser scribed lines as well as other sapphires with special specifications. We have sapphire substrate and Al2O3 substrate,RFQ today.

Minimum Order: 1 bags