Alloy

1. 8620 steel has high hardenability without brittleness. It is also called DIN 1.6523 and JIS SNCM220 steel. It also has good weldability, little tendency to form cold cracks, and good machinability and plasticity by cold deformation. It is used to make gears, shafts, bolts, springs, hand tools, etc.AISI 8620 alloy steel properties and 8620 steel composition as below. 2. 8620 chemical composition Carbon C: 0.18～0.23 Silicon Si: 0.15～0.35 Manganese Mn: 0.70～0.90 ASTM8620 alloy structural steel ASTM8620 alloy structural steel Sulfur S: Allowable residual content≤0.035 P: Allowable residual content≤0.035 Chromium Chromium: 0.40～0.60 Nickel Nickel: 0.40～0.70 Copper Cu: allowable residual content ≤ 0.030 Molybdenum Molybdenum: 0.15～0.25 3.AISI/SAE/ASTM 8620 Steel Heat Treatment （1）Glow It can be fully annealed by heating to 820 – 850℃ and holding until the temperature is uniform throughout the section, and furnace or air-cooled. （2）Cranking Tempering of heat treated and water cooled parts (not carburized) is done at 400 to 1300 F to improve the toughness of the case with minimal impact on its hardness. This also reduces the possibility of grinding cracks. （3）Hardening It is austenitized at around 840°C – 870°C and oil or water quenched depending on the cross-section size and complexity. And cool it in air or oil required. （4）Normalize 910ºC (1675ºF) and air cooled. This is another method to improve the machinability of 8620 steel materials. Normalizing can also be applied prior to case hardening. （5）Heat treatment This alloy can be hardened by heating to 1500 F and then water quenching. Carburize at 1650 to 1700 F in a suitable carburizing medium and oil quench to harden. Improved properties of the carburized case and core can be obtained by furnace cooling by carburizing at 1650-1700F and then reheating to 1575F. 4. For more steel product information,Please search our company(Dongguan Songshun Mould Steel Co., Ltd.) and check the official website!!! songshunsteel41404340

Minimum Order: 1 bags

Hot Rolled AISI 4340 Alloy Structural Steel Warehouse Introduction AISI 4340 alloy structural steel is a medium carbon nickel-chromium-molybdenum steel alloy, very similar to 4130 steel, but AISI 4340 alloy steel has high white spot sensitivity and temper brittleness, and is widely used in large- sized important quenched and tempered parts, shafts , transmission parts of heavy chemical machinery, etc., and AISI 4340 steel is a wear-resistant material with particularly good wear resistance, impact resistance and impact resistance, as well as excellent atmospheric corrosion resistance, and because the material is usually in Annealed condition, it also has the advantages of excellent hardenability, stability against overheating and short construction period. Our AISI 4340 alloy steel can be not only heat treated but also fusion and resistance welding. Chemical Composition The chemical composition of Song Shun AISI 4340 alloy structural steel. C:0.37-0.44 Si:0.17-0.37 S：≤0.035 P:≤0.035 Mn:0.50-0.80 Cr:0.60-0.90 Mo:0.15-0.25 Ni:1.25-1.65 Mechanical Properties The mechanical properties of AISI 4340 alloy structural steel Tensile strength σb (MPa): ≥980(100) Yield strength σs (MPa): ≥835(85) Elongation δ5 (%): ≥12 Area shrinkage ψ (%): ≥55 Impact energy Akv (J): ≥78 Elongation δ5 (%): ≥12 Area shrinkage ψ (%): ≥55 Impact energy Akv (J): ≥78 Impact toughness value αkv (J/cm2): ≥98(10) Sample size: sample blank size is 25mm AISI 4340 High Quality Alloy Steel Round Bar · GB steel number:   CN：40CrNiMoA   DIN：36CrNiMo4  JIS：SNCM439  BS： 816M40  US:AISI/ASTM4340 · Chemical component:   C:0.37-0.44  Si:0.17-0.37  S：≤0.35  P:≤0.35 Mn:0.50-0.80 Cr:0.60-0.90 Mo:0.15-0.25 N:1.25-1.65 · Usage: It is used as important quenched and tempered parts that require good toughness, high strength and large size, such as heavy machinery and high- load shafts, turbine shafts with a diameter greater than 250mm, helicopter rotor shafts, turbojet engine turbine shafts, blades, high Loaded transmission parts, crankshaft fasteners. gears, etc.; · Types:5140 /4140 / 4340 / 4142 / 15CrMo / 6150 / 38CrMoAI / 8620 ..... · Serve:OEM/ODM · Delivery status:With heat treatment (normalized, annealed or high temperature tempered) or without heat treatment Goods, the delivery status should be specified in the contract. Our company Dongguan Songshun Mould Steel Co., Ltd. specializes in the production of alloy steel for more than 10 years, mainly producing various alloy steel products, if you need more price, cooperation or quality information, please notify us jacklu@songshunsteel.com songshunsteel41404340

Minimum Order: 2 barrels

5140 steel is medium carbon modulation steel, cold heading die steel. The steel is moderate in price, easy to process, and can obtain certain toughness, plasticity and wear resistance after proper heat treatment. Normalizing can promote tissue spheroidization and improve the cutting performance of blanks with hardness less than 160HBS. Tempered at a temperature of 550~570℃, the steel has the best comprehensive mechanical properties. The hardenability of this steel is higher than that of S45C steel, and it is suitable for surface hardening such as high frequency quenching and flame quenching. Heat Treatment AISI/SAE/ASTM 5140 Steel Heat Treatment Heat treatment specification: quenching at 850℃, oil cooling; tempering at 520℃, water cooling, oil cooling 5140 surface quenching hardness is 52-60HRC, flame quenching can reach 48-55HRC Nitriding treatment 1.7035 is a nitridable steel, and the elements it contains are conducive to nitriding. 40Cr can obtain higher surface hardness after nitriding treatment, the highest hardness of 40Cr after nitriding treatment can reach 72~78HRA, and the core hardness can reach 43~55HRC. Nitriding workpiece process route: forging – annealing – roughing – quenching and tempering – finishing – stress relief – rough grinding – nitriding – fine grinding or grinding. Since the nitrided layer is thin and brittle, a high-strength core structure is required, so quenching and tempering heat treatment should be performed first to obtain tempered sorbite to improve the mechanical properties of the core and the quality of the nitrided layer. Weldability of 5140 steel: It is easy to segregate during crystallization, and is sensitive to crystallization cracks (a kind of thermal cracks), and it is easy to crack in arc craters and concave parts of welds during welding. The carbon content is high, and it is easy to obtain a hardened structure (martensitic structure) that is sensitive to cold cracks during rapid cooling. When the cooling rate of the superheated zone is large, it is easy to form hard and brittle high-carbon martensite to embrittle the superheated zone. Welding process points 1. Generally, welding is carried out in the annealed (normalized) state. 2. The welding method is not limited. 3. Use larger line energy to appropriately increase the preheating temperature. Generally, the preheating temperature and interlayer temperature can be controlled between 250 and 300 °C. 4. The welding material should ensure that the composition of the deposited metal is basically the same as that of the base metal, such as J107-Cr. 5. Quenching and tempering heat treatment should be carried out in time after welding. If it is difficult to carry out the quenching and tempering treatment in time, intermediate annealing or holding for a period of time at a temperature higher than preheating can be carried out to eliminate diffusible hydrogen and soften the structure. For products with complex structure and many welds, an intermediate annealing can be performed after a certain number of welds have been welded. If you have any questions,pls feel free to contact us. Songshun Always Open The Door For You. What we do? We specialized in steel as a professional special steel supplier, and also can give you technical advice and support for your business base on our professional technical knowledge. Because of our great and reliable quality and professional service in this field, our market is all around the world. Including Canada, Australia, Brazil, Turkey, Malaysia, Vietnam, Iran, Pakistan, UK and etc. At Songshun, we believe: You Get What You Pay for. Internationally, while someone seems to be lost in the desire to Chinese steel, others take an opposite attitude. Under the trend of economic globalization, we believe that high-quality steel is definitely not at a low price. As long as you can communicate with us with your heart, we will do our best to give you the best results. We see that as an opportunity: We’re excited to cooperate with customers from all around the world to change the impression for Chinese steel of other people. songshunsteel41404340

Minimum Order: 3 bushels

4140 steel, this steel has good workability, small processing deformation, good fatigue resistance, is a medium hardenability steel, 4140 has good strength and good comprehensive mechanical properties after heat treatment, good workability, yield High. The maximum use temperature is 427 degrees Celsius. 4140 strength, high hardenability, good toughness, small deformation during quenching, high creep strength and lasting strength at high temperature. It is used to manufacture forgings that require higher strength and larger quenched and tempered section than 35CrMo steel, such as large gears for locomotive traction, supercharger transmission gears, rear axles, connecting rods and spring clips that are heavily loaded, and can also be used for Drill pipe joints and fishing tools for oil wells below 2000m, and can be used for molds of bending machines. ASTM 4140 Surface Treatment and Heat Treatment 1.Surface Treatment Plate:Origin Black,Orign cold rolled bright, Machined,Grinded Bar:Origin Black,Orign cold rolled(drawn) bright,Turned,Peeled,Grinded Heat treatment specification Heat treatment standard: quenching at 850℃, oil cooling; tempering at 560℃, water cooling, oil cooling; 4140 Steel Applications It is used to manufacture forgings that require higher strength and larger quenched and tempered sections than 35CrMo steel, such as large gears for locomotive traction, supercharger transmission gears, rear axles, connecting rods and spring clips that are heavily loaded, and can also be used for Drill pipe joints and fishing tools for oil wells below 2000m, and can be used for molds of bending machines, etc.                     How is SAE 4140 steel tested? Our AISI 4140 steel round bar and steel plate composition detection is carried out by a spectrometer, which is fast, accurate and efficient in detection; hardness is tested by a hardness tester, The hardness tester is based on the Leeb hardness measurement principle, which can easily and quickly measure a variety of metal materials. While displaying the hardness measurement value immediately, it can be freely converted between different hardness scales, and the tolerance limit can be set in advance, and it will automatically alarm when it exceeds the range. 1. Measuring range: (170-960)HLD,(17-68.5)HRC,(19-651)HB,(80-976)HV,(3 , 0-100)HS, (59-85)HRA(13-100 )HRB 2. Measurement direction: support 360° (vertical down, oblique down, horizontal, oblique up, vertical up) 3. Hardness scale: Richter (HL), Brinell (HB), Rockwell B (HRB), Rockwell C (HRC), Rockwell A (HRA), Vickers (HV), Shore (HS) 4. Display: quarter dot matrix LCD 5. Data storage: maximum 500 groups (impact times 32 to 1) 6. Working voltage: 3V (2 AA size alkaline batteries connected in series) 7. Continuous working time: about 100 hours (when the backlight is not turned on) FAQ Q:Are you a factory or a trading company? A: The fact is that we are a company. We have own factory and several warehouses. Under the trend of globalization of the world, we established a professional foreign trade department to change the world. Q: What is your delivery date? A: The delivery date is about 10-30 days after receipt of payment. Q: Can I get some samples? A: We are honored to offer you samples. Q: What port do you usually ship from? A: We have 3 common ports,Tianjin, Shanghai and Shen. Q: What is the payment terms? A: T/T is our priority, L/C is also OK for us. Songshun specialized in Special Steel for almost 20 years. We can supply mold steel, high speed steel, alloy steel, free cutting steel and etc.Welcome your contact 24 hours a day!!! E-mail:jacklu@songshunsteel.com Skype , /Whatsapp/Wechat:+86-18269260283 Songshun Tiktok:mikizhuo Songshun Facebook:Songshun Steel Songshun YouTube:MiKi Zhuo Songshun Company Website:https://steelpurchase.com/ http://www.songshunsteel.com/ songshunsteel , 41404340

Minimum Order: 1 bags

4140 steel is a kind of alloy structural steel. It belongs to the steel with the American grade equivalent to the 42CrMo grade in my country. This kind of steel belongs to the medium hardenability steel with high yield, good comprehensive mechanical properties, good strength, good toughness and hardenability. High advantages, its carbon content is 0.33%-0.48%, its tensile strength is 795 MPa, and its hardness is 241HB. After heat treatment at 4140, it has good strength and good comprehensive mechanical properties, and it has good manufacturability. Fasteners, salvage tools, etc. China GB steel number 42CrMo, Germany DIN steel number 42CrMo4, Germany DIN material number 1.7225, French NF standard 40CD4/42CD4, Japanese JIS standard SCM440, British BS standard 708M40/708A42/709M40, American AISI/ASTM 4140, American SAE 4140, American UNS Standard G41400 (4140 alloy structural steel, executive standard: ASTM A29/A29M-04) Mechanical properties: Tensile strength σb (MPa): ≥1080(110) Yield strength σs (MPa): ≥930(95) Elongation δ5 (%): ≥12 Area shrinkage ψ (%): ≥45 Impact energy Akv (J): ≥63 Impact toughness value αkv (J/cm2): ≥78(8) Hardness: ≤217HB Sample size: sample blank size is 25mm Established in 2009,Songshun Steel supplies a wide range of carbon, alloy and tool steel products, including high speed tool steel, cold work tool steel, hot work tool steel, plastic mould steel, engineering steel and machine structural steel etc. After more than 10 years development and growing, Songshun Steel becomes one comprehensive special steel factory, stockist and exporter. Combined with experienced exporting team and professional technical knowledge, Songshun Steel offers both technical advice and support, as well as global professional steel solution and service. Due to satisfactory reliable quality and professional service, Songshun expands our market worldwide, such as Colombia, Chile, Spain, Turkey, Iran, Vietnam, Malaysia ,UAE, Canada, Brazil, Mexico and so on. Songshun specialized in Special Steel for almost 20 years. We can supply mold steel, high speed steel, alloy steel, free cutting steel and etc.Welcome your contact 24 hours a day!!! E-mail:jacklu@songshunsteel.com Skype , /Whatsapp/Wechat:+86-18269260283 Songshun Tiktok:mikizhuo Songshun Facebook:Songshun Steel Songshun YouTube:MiKi Zhuo Songshun Company Website:https://steelpurchase.com/ http://www.songshunsteel.com/ songshunsteel , 41404340

Minimum Order: 1 bags

(1) 1.6511 Alloy Steel Rod Refers To The Corresponding Steel Number China GB steel number 40CrNiMoA, German DIN steel number 36CrNiMo4, German DIN material number 1.6511, French NF standard 40NCD3, Japanese JIS standard SNCM439, British BS standard 816M40, American AISI/ASTM4340, American UNS standard G43400. (2) 1.6511 Alloy Steel Rod Chemical Composition C:0.37-0.44 Si:0.17-0.37 S：≤0.035 P:≤0.035 Mn:0.50-0.80 Cr:0.60-0.90 Mo:0.15-0.25 N:1.25-1.65 (3) 1.6511 Alloy Steel Rod Surface Treatment Plate: Origin Black, Orign cold rolled bright, Machined, Grinded Bar:Origin Black, Orign cold rolled(drawn) bright, Turned, Peeled, Grinded (4) Charateristics 4340 steel offers toughness and high strength inthe heat treated condition, with in roun , d bar 4340 is available fully certified and suitable for applicat , ions  requiring a quality tensile alloy steel.AISI 4340 is commonly supplied quenched and tempered with a hardness of between 24 to 29HRc (5) Contact us Feel free to contact us,we are glad to serve for you. Songshun Always Open the Door for You. MiKi Zhuo Skype/Whatsapp/Wechat:+86-18269260283 A , DD:No.4 Dongda Street, Shatou, Changan Town, Dongguan City, Guangdong Province, P.R.C China songshunmoldsteel41404340

Minimum Order: 1 bags

Description of 4340 chromoly steel:4340 alloy steel is an iron-based alloy containing nickel, chromium and molybdenum. The relatively high carbon content gives this alloy exceptional strength in applications where severe service conditions exist.4340 alloy steel has high strength, good toughness and good ductility. In addition, the alloy is not prone to embrittlement. 4340 steel application: It is used as important quenched and tempered parts that require good toughness, high strength and large size, such as heavy machinery and high-load shafts, turbine shafts with a diameter greater than 250mm, helicopter rotor shafts, turbojet engine turbine shafts, blades, high Loaded transmission parts, crankshaft fasteners. Gears, etc.; can also be used for rotor shafts and blades whose operating temperature exceeds 400 °C; can also be used to manufacture important parts with special performance requirements after nitriding treatment, and can be used for ultra-high temperature after low temperature tempering or austempering. Use of strength steel. 4340 Steel Features:It has high strength, toughness, excellent hardenability and stability against overheating, good plasticity and heat resistance, uniform material, high working reliability, weldability, non-leakage, and simple steel structure production. Short construction period and good assembly. 4140 steel processing technology: Heat treatment standard: quenching at 850℃, oil cooling; tempering at 560℃, water cooling, oil cooling; Metallographic structure: tempered sorbite Heat treatment: 1. Normalizing: Heat the furnace to 900°C~930°C, keep the thickest cross section per inch at this temperature for one hour, and cool in air. 2. Heat to austenitizing at a temperature of 860℃~885℃, and keep the thickest cross section per inch for one hour at this temperature 3. Normalizing or oil quenching, and cooling to a maximum temperature of 121°C 4. Temper at a temperature that achieves the following mechanical properties. The thickest cross-section per inch is held for one hour at the tempering temperature, and the tempering temperature range is 640 ° C ~ 680 ° C 5. For each heat treatment process, a heat treatment chart must be drawn. 6. The mechanical property test shall be carried out in accordance with the stipulations of ASTM. A-370. The sample material used for the test shall be cut from the test bar of the same furnace steel. The casting or forging represented by the sample and the test bar shall be in the same furnace. The test bar shall be heat treated in the same furnace together with the charge. 7. The mechanical properties should meet the following requirements: (Tested with a test bar, sampling according to APT 6A, 110K standard) - Tensile strength minimum lb/inch (862) Yield strength minimum lb/inch 110.000 (758) 2 inches The minimum value of elongation is 15% and the minimum value of section shrinkage rate is %40. Brinell hardness HB285 ~ take, the casting or forging represented by the sample and the test bar must be in the same furnace, and the test bar should be heat treated in the same furnace together with the charge. 8. The mechanical properties should meet the following requirements: (tested with test bars, sampling according to APT 6A, 110K standard) - minimum tensile strength lbs/inch (862) minimum yield strength lbs/inch (758) 2 inches Minimum elongation %15 Minimum shrinkage of section %40 Brinell hardness HB285~352 9. Marking: Each part shall be printed with heat treatment marks and hardness with low stress steel stamp. Company Overview Established in 2009,Songshun Steel supplies a wide range of carbon, alloy and tool steel products, including high speed tool steel, cold work tool steel, hot work tool steel, plastic mould steel, engineering steel and machine structural steel etc. After more than 10 years development and growing, Songshun Steel becomes one comprehensive special steel factory, stockist and exporter.songshunmoldsteel41404340 ,

Minimum Order: 1 bags

Low alloy steel refers to alloy steel with less than 5% of total alloying elements. Low alloy steel is relative to carbon steel. On the basis of carbon steel, one or several alloying elements are intentionally added to the steel in order to improve the properties of the steel. When the amount of alloy added exceeds the general content of the normal production method of carbon steel, the steel is called alloy steel. When the total amount of alloy is less than 5%, it is called low alloy steel, ordinary alloy steel is generally less than 3.5%, alloy content between 5-10% is called medium alloy steel, and more than 10% is called high alloy steel. China's steel output has exceeded 600 million tons, the quantity of steel is no longer the main contradiction, and the contradiction of unreasonable steel varieties and structure is very prominent. The main task of the current industry is to strive to improve the market competitiveness of products, stand at a new starting point for sustainable development, and make vigorous development of low-alloy steel an important part of the development strategy. Many ordinary steel enterprises have realized that the production of low-alloy steel is the key to improving the technical content and added value of products in the adjustment of the steel variety structure and the preparation of scientific and technological development plans. The management cadres felt that "success is also low-alloy steel, and failure is also low-alloy steel", and they urgently demand a comprehensive understanding of low-alloy steel. The production situation of ordinary low alloy steel in my country can be summarized into the following points: 1. It is low carbon in terms of carbon content, and the carbon content is generally less than 0.20%; 2. In terms of alloys, primary steel and binary steel occupy a large proportion; 3. In terms of supply status, most of them are delivered in hot-rolled state; 4. Many steel grades add rare earth elements to improve the overall performance; 5. Most common low alloy steels are ferrite + pearlite type. Our company Dongguan Songshun Mould Steel Co., Ltd. specializes in the production of alloy steel for more than 10 years, mainly producing various alloy steel products, if you need more price, cooperation or quality information, please notify us jacklu@songshunsteel.com

Minimum Order: 1 bags

Established in 2009,Songshun Steel supplies a wide range of carbon, alloy and tool steel products, including high speed tool steel, cold work tool steel, hot work tool steel, plastic mould steel, engineering steel and machine structural steel etc. After more than 10 years development and growing, Songshun Steel becomes one comprehensive special steel factory, stockist and exporter. Combined with experienced exporting team and professional technical knowledge, Songshun Steel offers both technical advice and support, as well as global professional steel solution and service. Due to satisfactory reliable quality and professional service, Songshun expands our market worldwide, such as Colombia, Chile, Spain, Turkey, Iran, Vietnam, Malaysia ,UAE, Canada, Brazil, Mexico and so on. We offer a wide range of information and high quality steel products on 4140 and 4340 steel, for more information on our 4140 and 4340 steel products, please contact us today. To discuss pricing details, please request a quote. MiKi Zhuo E-mail:jacklu@songshunsteel.com Skype/W , hatsapp/Wechat:+86-18269260283 ADD:No.4 Dongda Street, Shatou, Changan Town, Dongguan City, Guangdong Province, P.R.C China For more 4140 steel product information, please click this link: https://steelpurchase.com/4140-scm440-172 , 25-steel/ songshunmoldsteel41404340

Minimum Order: 2 barrels

With the development of science, technology and industry, higher requirements are put forward for materials, such as higher strength, resistance to high temperature, high pressure, low temperature, corrosion resistance, wear and other special physical and chemical properties. To meet the requirements, alloy steel plates appeared. 1.Alloy Steel Plate Performance Issues With the development of science, technology and industry, higher requirements are put forward for materials, such as higher strength, resistance to high temperature, high pressure, low temperature, corrosion resistance, wear and other special physical and chemical properties. fulfil requirements. The performance of carbon steel mainly has the following shortcomings: (1) Low hardenability Under normal circumstances, the maximum hardenable diameter of carbon steel water quenching is only 10mm-20mm. (2) The strength and yield strength are relatively low. For example, the σs of ordinary carbon steel Q235 steel is 235MPa, while the σs of low alloy structural steel 16Mn is more than 360MPa. The σs/σb of 40 steel is only 0.43, which is much lower than that of alloy steel. (3) Poor tempering stability Due to the poor tempering stability, when carbon steel is quenched and tempered, a lower tempering temperature is required to ensure higher strength, so that the toughness of the steel is low; in order to ensure better Toughness, and the strength is low when the high tempering temperature is used, so the comprehensive mechanical properties of carbon steel are not high. (4) Can not meet the requirements of special properties Carbon steel is often poor in terms of oxidation resistance, corrosion resistance, heat resistance, low temperature resistance, wear resistance and special electromagnetic properties, and cannot meet the needs of special performance properties. 2.The difference between carbon steel and alloy steel plate The performance of carbon steel mainly has the following shortcomings: (1) Low hardenability In general, the maximum hardening diameter of carbon steel water quenching is only 10mm-20mm. (2) The strength and yield strength are relatively low. For example, the σs of ordinary carbon steel Q235 steel is 235MPa, while the σs of low alloy structural steel 16Mn is more than 360MPa. The σs/σb of 40 steel is only 0.43, which is much lower than that of alloy steel. (3) Poor tempering stability Due to the poor tempering stability, when carbon steel is quenched and tempered, a lower tempering temperature is required to ensure higher strength, so that the toughness of the steel is low; in order to ensure better Toughness, and the strength is low when the high tempering temperature is used, so the comprehensive mechanical properties of carbon steel are not high. (4) Can not meet the requirements of special properties Carbon steel is often poor in terms of oxidation resistance, corrosion resistance, heat resistance, low temperature resistance, wear resistance and special electromagnetic properties, and cannot meet the needs of special performance properties. 3.Our Company Established in 2009,Songshun Steel supplies a wide range of carbon, alloy and tool steel products, including high speed tool steel, cold work tool steel, hot work tool steel, plastic mould steel, engineering steel and machine structural steel etc. After more than 10 years development and growing, Songshun Steel becomes one comprehensive special steel factory, stockist and exporter. Combined with experienced exporting team and professional technical knowledge, Songshun Steel offers both technical advice and support, as well as global professional steel solution and service. Due to satisfactory reliable quality and professional service, Songshun expands our market worldwide, such as Colombia, Chile, Spain, Turkey, Iran, Vietnam, Malaysia ,UAE, Canada, Brazil, Mexico and so on. 4.Contact Us MiKi Zhuo E-mail:jacklu@songshunsteel.com Skype/W , hatsapp/Wechat:+86-18269260283 ADD:No.4 Dongda Street, Shatou, Changan Town, Dongguan City, Guangdong Province, P.R.C China Company website: https://steelpurchase.com/ http://w , ww.songshunsteel.com/ songshunmoldsteel41404340 ,

Minimum Order: 1 bags

1.Alloy Tool Steel Round Bar Alloy tool steel is a type of steel in which chromium, molybdenum, tungsten, vanadium and other alloying elements are added on the basis of carbon tool steel to improve hardenability, toughness, wear resistance and heat resistance. It is mainly used in the manufacture of measuring tools, cutting tools, impact- resistant tools, cold and hot molds and some special-purpose tools. Steel with alloying elements such as Si, Mn, Ni, Cr, W, Mo, and V added to carbon tool steel. The addition of Cr and Mn can improve the hardenability of tool steel, and other elements can be added selectively or at the same time according to requirements (the total amount of addition generally does not exceed 5%), that is, a series of alloy tool steels are formed. 2.Category of use The hardenability, hardenability, wear resistance and toughness of gold tool steel are higher than those of carbon tool steel, and can be roughly divided into three categories: steel for cutting tools, molds and measuring tools. Among them, steels with high carbon content (carbon mass fraction greater than 0.80%) are mostly used to manufacture cutting tools, measuring tools and cold work dies. The hardness of such steels after quenching is above HRC60 and has sufficient wear resistance; steels with moderate carbon content ( Carbon content of 0.35%~0.70%) is mostly used in the manufacture of hot work molds. The hardness of this type of steel after quenching is slightly lower, which is HRC50~55, but the toughness is good. The cutting tool produces strong wear and heat under working conditions, as well as vibration and a certain impact load. Steel for cutting tools should have high hardness, wear resistance, red hardness and good toughness. In order to ensure its high hardness and meet the needs of forming alloy carbides, the carbon content in steel is generally 0.80% to 1.45%. Chromium is the main alloying element of this type of steel, and its mass fraction is generally 0.50% to 1.70%. Some steels also contain tungsten to improve the performance of cutting metals. This type of tool steel contains alloying elements, so the hardenability is better than that of carbon tool steel, the deformation caused by heat treatment is small, and it has high hardness and wear resistance. Commonly used steels are chromium steel, silicon-chromium steel and chromium- tungsten-manganese steel. [Applications]: Mainly used to manufacture low-speed cutting tools (such as woodworking tools, fitter tools, drills, milling cutters, broaches, etc.) and measuring tools (such as calipers, micrometers, block gauges, templates, etc.). Measuring tool steel is required to have high hardness (62-65HRC), high wear resistance, sufficient strength and toughness, and high hot hardness (that is, the cutting tool can still maintain high hardness at high temperature); in order to ensure the accuracy of measurement, measuring tools are required. Cutting tool steel has good dimensional stability. [Chemical composition]: Measuring tool steel has high carbon content, wC=0.8%～ 1.50%, to ensure high hardness and wear resistance. The added alloying elements are Cr, Si, Mn, W, etc., to improve the hardenability, tempering resistance, hot hardness and wear resistance of steel. [Commonly used cutting tool steel]: 9SiCr is a widely used cutting tool steel, which is used to make various thin-edged low-speed cutting tools that require small deformation, such as die, tap, reamer, etc. [Commonly used measuring tool steel]: High-precision measuring tools (such as block gauges) can be made of measuring tool steel such as Cr2, CrWMn, etc., or bearing steel (such as GCr15); simple measuring tools (such as calipers, templates, rulers, gauges, etc.) are multi-purpose Carbon tool steel (such as T10A); for measuring tools that require precision and must prevent corrosion, stainless steel 3Cr13 and 9Cr18 are used. [Heat treatment]: The pre-heat treatment of measuring and cutting tool steel is spheroidizing annealing, and the final heat treatment is quenching and low- temperature tempering. After heat treatment, the hardness reaches 60-65HRC. High precision gauges can be cold treated after quenching to reduce the amount of retained austenite and thus increase their dimensional stability. In order to further improve dimensional stability, aging treatment can also be carried out after quenching and tempering. songshunmoldsteel41404340

Minimum Order: 1 bags

4140 Steel Product Information Steel Grade: 4140 Alloy steel Standard: AISI/ASTM/DIN/NF/JIS/GB/BS Place of Origin:Guangdong, China Brand Name:Songshun Model Number:4140/1.7225/42CrMo Technique:Hot Rolled Application:Die Steel Bar Special Use:Mold Steel Tolerance:±10% Shape:Round bars/Flat bar/Plate Delivery Time:8-14 days Heat treatment:Annealing/Q+T Processing Service:Bending, Welding, Decoiling, Cutting, Punching Technology:Hot Rolled/Forged/Clod Drawn Surface treatment:Black/Peeling/Polishing/Machined Deli , very condition:Hot rolled or forged/ Peeled or black surface/annealed or QT Test:UT100%/Elements testing Certificate:ISO/Mill certificate Service:Sample free and 24 hours online Experience:Ten years manufacturer experience Company Strength After more than ten years of development and growth, Songshun Iron and Steel has become a comprehensive special steel production enterprise, inventory enterprise and export enterprise. With an experienced export team and professional technical knowledge, Songshun Steel provides customers with technical advice and support, as well as global professional steel solutions and services. With satisfactory and reliable quality and professional services, the company's markets are all over the world, such as Colombia, Chile, Spain, Turkey, Iran, Vietnam, Malaysia, United Arab Emirates, Canada, Brazil, Mexico, etc. Welcome To Get a Quote MiKi Zhuo E-mail:jacklu@songshunsteel.com Skype/W , hatsapp/Wechat:+86-18269260283 ADD:No.4 Dongda Street, Shatou, Changan Town, Dongguan City, Guangdong Province, P.R.C China For more 4140 steel product information, please click this link: https://steelpurchase.com/4140-scm440-172 , 25-steel/ Company website: https://steelpurchase.com/ http://w , ww.songshunsteel.com/ songshunmoldsteel41404340

Minimum Order: 1 bags

1.Product name JIS SCM440 Steel Mechanical Properties Alloy Structual Steel 2.keyword   SCM440 Steel Mechanical Properties   3.Standard AISI/ASTM/DIN/NF/JIS/GB/BS 4.Steel Grade AISI 4140/ASTM 4140/DIN 1.7225 /NF 40CD4 /JIS SCM440 /GB 42CrMo /BS 708M40 5.Chemical Compositions(%) C: 0.38-0.45   Si: 0.17-0.37  Mn: 0.50 , -0.80  P≤0.035  S ≤0.035   Cr: 0.90-1.20  Mo: 0.15-0.25 6.Mechanical properties Tensile strength σb (MPa): ≥1080(110) Yield strength σs (MPa): ≥930(95) Elongation δ5 (%): ≥12 Area shrinkage ψ (%): ≥45 Impact energy Akv (J): ≥63 Impact toughness value αkv (J/cm2): ≥78(8) Hardness: ≤217HB Sample size: sample blank size is 25mm 7.Surface treatment Black/Peeling/Polishing/Machined 8.Techniqu , e Cold/Hot rolled, Cold-Drawn or Hot Forged 9.Heat Treatment Annealed; Quenched; Tempered 10.Delivery Condition Hot Rolled or Forged/Peeled or Black Surface/Annealed or QT Heat treatment standard Quenching at 850℃, oil cooling; tempering at 560℃, water cooling, oil cooling 10.Feature This steel has good strength, good toughness, high hardenability, good workability, small processing deformation, quite good fatigue resistance, small deformation during quenching, high creep strength and durable strength at high temperature and so on. 11.Test SGS/UT100%/Elements Testing 12.Certificate SGS/ISO/Mill Certificate 13.Delivery status Delivered in heat-treated (normalized, annealed or high temperature tempered) or unheated state 14.E-mail jacklu@songshunsteel.com 15.Skype/Whatsapp/ , Wechat +86-18269260283 16.Company website https://steelpurchase.com/ http://www.songs , hunsteel.com/ 17.songshunmoldsteel41404340

Minimum Order: 1 bags

Heat Treatment 4140 Alloy Steel Equivalent Steel Grade  China GB steel number 42CrMo, Germany DIN steel number 42CrMo4, Germany DIN material number 1.7225, French NF standard 40CD4/42CD4, Japanese JIS standard SCM440, British BS standard 708M40/708A42/709M40, American AISI/ASTM 4140, American SAE 4140, American UNS Standard G41400 Heat Treatment 4140 Alloy Steel Chemical Composition C:0.38-0.45 Si:0.17-0.37 S：≤0.035 P:≤0.035 Mn:0.50-0.80 Cr:0.90-1.20 Mo:0.15-0.25 Ni:≤0.30 Cu≤0.30 SAE 4140 Mechanical Properties Tensile Strength σb (MPa):≥1080(110) Yield Strength σS (MPa):≥930(95) Elongation δ5 (%):≥12 Reduction ψ (%):≥45  Impact Energy Akv (J):≥63 Impact Toughness akv (J/cm2):≥78(8) Annealed Hardness ≤217HB Our advantage Focus on the steel industry for more than ten years Strength factory Professional service Quality assurance Customized according to customer requirements Factory price Fast shipping time Good after-sales service Happy to work with customers High repurchase rate, etc. songshunmoldsteel41404340

Minimum Order: 1 bags