Offers to Sell

Application JOEO IPX1-6 rain test chamber, ip test chamber, water spray test equipment Applied to plastics, rubber, paint, coatings, printing ink, paper, pharmaceuticals, food, cosmetics, textiles, auto parts, packaging materials, building materials, electricity and the electrical products; it provide an important testing data for scientific research, product development and quality control. Description When testing products in JOEO IPX1-6 water spray test chamber, place the sample on the turntable of the test chamber. After the test chamber is started, the water flow is controlled by the flowmeter and pressure, and enters the pendulum pipe through the pipe. According to the test requirements, the pendulum tube swings back and forth to pour water into the test object.  the pendulum tube swings 60° on both sides of the vertical line, a total of 120°. It's 15 cents a stick. The test lasted five minutes. Then rotate the case horizontally 90° and test for 5min. Structure: The door frame of the water spray chamber  is insulated with high temperature and aging resistant silicone rubber door seals, the outer shell is coated with rust-resistant cold-rolled sheet, and the outer box is made of SUS304 stainless steel, which has a long service life and is not easy to rust The rotary table is made of SUS304 stainless steel, which has good corrosion resistance. The height of the turntable can be adjusted, because the height of the test sample and the height of the Spiracle must have corresponding fixed values.If you need more models about our test equipment, please reference our chamber-testing（.）com JOEO rain spray test chamber swing tube is also made of 304 stainless steel. The swing tube drive adopts a stepper motor, which has the advantages of low noise, fast speed, and accurate angle. The standard water tank of the rain testing equipment has an automatic water intake function and is equipped with high and low water level alarm detection, which can effectively prevent the water pump from being damaged due to water shortage. The stress free door handle can open and close the test door with one hand, making it convenient and labor-saving.

Minimum Order: 1 bags

Application JOEO humidity control chamber are designed for testing the capability of heat-endurance, cold-endurance, dryness-endurance, and humidity-endurance, suitable for quality control of the industries of electron, electrical equipment, ,LED, ic chips, vehicle, metal, foodstuffs,plastic products, chemistry, building materials, luggage, adhesion tape, printing, packaging, etc.If you need more models about our test equipment, please reference our chamber-testing（.）com Description JOEO humidity control chamber temperature control air ducts are designed as double air ducts, connected to the studio but isolated. The path of the wind is in the form of wind return, the partition plate is made of high-quality stainless steel plate cold bending, and the outlet adopts adjustable louvers. The temperature control duct is provided with indirect heater, saturated wet air inlet, refrigeration dehumidification evaporator and circulating air supply wheel Features  Humidity control chamber body adopts an arc shape, the surface is treated with matte stripes, and the flat non-reaction handle is adopted, which is easy to operate, safe, and reliable; The box adopts rectangular multi-layer glass viewing window, which can be used to observe the test items during the test. The window is equipped with an anti- sweat electric heater device to prevent water vapor from condensing and water droplets, and high-brightness PL fluorescent lamps keep the constant climate chambers interior of the box illuminated; The double-layer insulation of the box door is tight and airtight, which can effectively isolate internal temperature leakage. With an external water supply system, it is convenient to supplement the water supply of the humidification barrel, and it can be recycled and used automatically; The compressor circulation system adopts the French “Taikang” brand, which can effectively remove the lubricating oil between the condenser tube and the capillary tube, and the whole series adopts environmentally friendly refrigerants (R23, R404, R507); Humidity control chamber's controller adopts an imported LCD screen, which can display the measured value, set value, and time at the same time; The controller has multi-segment program editing and temperature, and humidity can do fast (OUICK) or slope (SLOP) control; The built-in moving pulley is easy to move and place and has a strong positioning screw to fix the position.

Minimum Order: 1 bags

Application JOEO temperature humidity chamber is used to simulate the combination of temperature and humidity of the product in a climatic environment (high and low temperature operation, storage, temperature cycling, high temperature and high humidity, low temperature and low humidity, dew testing, etc.). Suitable for aerospace products, information electronic instruments, materials, electrical, electronic products, all kinds of electronic components at high and low temperatures to test their performance indicators.If you need more models about our test equipment, please reference our chamber-testing（.）com If you need more models about our test equipment, please reference our chamber- testing（.）com

Minimum Order: 1 bags

JOEO Walk In Salt Spray Chamber is different from basic salt spray test chamber.Walk In Salt Spray Chamber exposes sample to a series of different environments in repetitive cycles that incorporate temperature , humidity, salt spray and dry.  Accelerated corrosion test methods included ASTM B117, ASTM BG85, ISO9227, IEC60068-2-52, iec61701-2, ISO7253 and many others. Test Object: battery pack andsystem. Refer GB/T4 part 5.5.2 test method, test according to GT/T2423.17 test conditions.If you need more models about our test equipment, please reference our chamber-testing（.）com The salt solution was made up with sodium chloride (chemically pure and analytically pure) and distilled or deionized water，Its concentration is (5 + 1)% (mass fraction). (35 ± 2) ℃, the measured pH value is between 6.5-7.2. Placed the test objects in the salt spray chamber for cycling test. Each cycling duration for 24h. Spray salt solution to the test object for 8 hours under the temperature of (35± 2) ℃ , remain for 16 hours. Between the forth and the fifth hour in one cycles should be according to test requirement in GB/T 28046.1-2011, test mode with 3.2. Total 6 cycles testing. Salt Spray Chamber is not necessary for the test objects being installed in passenger, luggage or cargo compartments.

Minimum Order: 1 bags

Description JOEO UV Test Chamber,uv testing chamber,uv test machine,uv light test chamber,uv aging test chamber can reproduce the effects of sunlight, and the condensation and water spraying system can reproduce the effects of rain and dew. The radiated energy and temperature can be controlled throughout the test cycle. A typical test cycle is usually ultraviolet light exposure at high temperature and relative humidity in a 100% dark wet condensation cycle. JOEO uv weather resistance test chamber, uv weathering chamber,light fastness tester is suitable for non-metallic materials sun resistance test and artificial light source aging test. This product can simulate the damage and oxidation caused by the product under the conditions of sun, rain, moisture and dew, including bleaching, discoloration, brightness decrease, powder, cracking, blurring, brittleness, strength decrease, etc. Typical applications in paint and coatings, automotive industry, plastic products, wood products and other industries Features： Original UVA or UVB lamps from the United States ensure comparability of test results. We have independent intellectual property rights and are the first in China. Our ballast can extend the lifespan of the lamp tube to 6000 hours, greatly saving users on usage costs. The high-precision Pt 100 temperature sensor on the blackboard automatically controls temperature. The operator can freely set different programs. Touch screen control, user- friendly interface, allowing users to view any parameters during the testing process.If you need more models about our test equipment, please reference our chamber-testing（.）com Real time data collection and storage, all test data automatically converted to Excel format for storage. JOEO uv weather test chamber with a TCP/IP Ethernet interface, users can remotely control the BUV through a TCP/IP network. Equipped with a booster pump, even if the outdoor water pressure is not enough, the BUV can still work normally with this booster pump.

Minimum Order: 1 bags

Battery Walk In Test Chamber JOEO Walk In Test Chamber's temperature cyclic stress screening is to change the external environmental stress by using the temperature acceleration technique (the product produces alternating expansion and contraction when circulating in the upper and lower extreme temperatures) under the design strength limitation, so as to generate thermal stress and strain in the product.If you need more models about our test equipment, please reference our chamber-testing（.）com It can set different stress screening temperature change rate 5℃/min,10℃/min,15℃/min,20℃/min  Wa , lk In test chamber(ESS chamber) is suitable for the whole product, parts and materials for high temperature, low temperature, high and low temperature cycling & temperature stress screening (ESS) test and constant humidity and cyclic damp heat test. Meeting standards MIL-STD-2164, MIL-344A-4-16, MIL-2164A-19, NABMAT-9492,GJB-1032-90, GJB/Z34- 5.1.6, IPC-9701 SAFETY IN THE LABORATORY AND PROTECTION OF THE STAFF During the temperature tests, overchargings or malfunctions of the batteries may occur. This can lead to the destruction of the batteries. Increasing storage sizes cause increasing impacts of possible failures and potential risks during tests with lithium batteries. For this reason, safety in the laboratory, in particular the protection of the staff, during such tests has the highest priority. To assure this safety in your lab chamber during tests with lithium batteries in a temperature- or environmental humidity chamber, we can offer safety devices. Here, JOEO Battery Walk In Test Chamber following customers demand that the safety test chambers can be adapted individually,  Please feel free to inquiry from us online!

Minimum Order: 1 bags

Application    JOEO factory altitude simulation chamber is designed to allow users to perform temperature, humidity, and altitude condition tests in a combined test chamber, and create multiple conditions to meet multiple test requirements at the same time.If you need more models about our test equipment, please reference our chamber-testing（.）com   Designed to simulate altitude conditions up to 100,000 feet.  Provides simultaneous temperature/altitude testing from site altitude to 65,000 feet for high altitude test chamber testing.  Humidity test can only be performed at the altitude of the site.  Heated inspection window to ensure that the test room is clearly visible. Details: Meets international standards DO160, ASTM, MIL-STD-781, -810 High altitude chamber up-to 150,000 feet Temperature range -70°C to +180°C, Humidity range 20 to 95% Feature High Altitude Chamber Testing of avionics or other aerospace equipment to simulate actual conditions it might experience. Simulation of high-altitude conditions like might be found in mountainous regions. High altitude chamber are used for autom otivetests to simulate mountainous conditions and totest computers, electronics and packaging materials that may be shipped via airfreight. It is especially important for defense and aerospace applications where pressure and vacuum conditions are even more intense. These chambers are JOEO company's most classic test chamber. JOEO (temperature/altitude) and ACC-Series (temperature/altitude/humidity) chambers are designed to allow the userto perform temperature, humidity. and altitude condition testing in one combined test chamber More than one condition can be created simultaneously to satisfy many types of test requirements.

Minimum Order: 1 bags

MicroF_W168 is a water-based micronized polyethylene homopolymer. The average particle size of MicroF_W168 is between 5.5 and 6.0 microns, and the maximum particle size is 21 microns. Application: Top grade water-based ink, water-based wood coating, Waterborne coatings, etc; Addition quantity: about 1%, can be added directly in the water-based system; Advantage: can be directly dispersed in the water-based system; Characteristics: good storage stability, good smoothness and wear-resistant performance.

Application Temperature humidity and vibration test chamber conforms to the national standard and meets the specific test requirements. Through the combination of high and low temperature, low temperature, temperature change, shock, wet and thermal vibration and other environmental reliability tests, widely used in electronic and electrical products, auto parts, materials and so on Feature The insulation material is fireproof and high strength PU polyurethane foam insulation material. High precision perfect appearance design, the external use of double-sided cold rolled plate electrostatic powder coating material, the internal use of SUS#304 high temperature stainless steel. The control system and control circuit components are made of well-known brands.If you need more models about our test equipment, please reference our chamber-testing（.）com The introduction of Japan, Germany advanced refrigerator control technology, energy saving more than 20%. Application Temperature humidity and vibration test chamber with suitable vibration test bench can meet the requirements of temperature, humidity and vibration test. The three integrated test system has been widely used in aviation, aerospace, ship, electrical, electronic, communication and other fields.

Minimum Order: 1 bags

Introduction  JOEO ozone aging test chamber through the simulation and enhancement of ozone conditions in the atmosphere, to study the impact of ozone on rubber, and then determine and evaluate rubber resistance to ozone and aging methods, take effective anti-aging measures to improve the service life of rubber products. JOEO Ozone test chamber can be used to test rubber products with static tensile deformation, such as vulcanized rubber, thermoplastic rubber, cable insulation bushing, etc. The test pieces were exposed to the airtight air in the ozone chamber with no light, constant ozone concentration and constant temperature at a predetermined time, and the surface cracks and other properties of the test pieces were observed to evaluate the ozone aging resistance of the rubber. JOEO Ozone test chamber is widely used in product quality control in measurement quality control. Rubber and plastics; Automobile production; Wire and cable; Packaging materials; Instruments and meters; Medical equipment; Civil nuclear energy; Civil aviation; Institutions of higher learning; Research laboratories; Inspection arbitration, and technical supervision departments such as rubber products If you need more models about our test equipment, please reference our chamber- testing（.）com   Features Stainless steel inside and outside for ozone testing room Made of iron with powder coating on the outside Durable ozone generator (ozone laboratory) The insulation material is high-density glass fiber cotton The bottom is a universal round wheel and fixed feet The window material is multi-layer tempered glass, and the interior is conductive with chips Refrigeration compressor oil pressure protection Lack of reverse phase protection system. Overload protection of circulating fan motor

Minimum Order: 1 bags

Application JOEO temperature humidity chamber is used to simulate the combination of temperature and humidity of the product in a climatic environment (high and low temperature operation, storage, temperature cycling, high temperature and high humidity, low temperature and low humidity, dew testing, etc.). Suitable for aerospace products, information electronic instruments, materials, electrical, electronic products, all kinds of electronic components at high and low temperatures to test their performance indicators.If you need more models about our test equipment, please reference our chamber-testing（.）com

Minimum Order: 1 bags

Common Rail Injector Valve Assembly F00V C01 324 0 445 110 154 Injector Valve Set 0 445 110 159 Injector Valve Set 0 445 110 162 Injector Valve Set 0 445 110 165 Injector Valve Set (8AU) Whats--App 86--1--3--3--8--6--9--0--1--3--1--5 Doney----(a , t)----china-lutong---(dot)----net CHINA-LUTONG technology provides an effective solution for diesel engine – offering efficiency, performance, reliability and minimal emissions. The quality of us is in the advancein Auto Parts field.We are diesel parts manufacturer, we have our own factory, we mainly produce: head rotor, plungers,nozzles, injector, repair kit etc... What can we give you : 1. High quality products, factory directly sale 2 good service include before sale and after sale 3 Fast delivery (3-5days) 4. Strong Supply Capacity with sufficient stock. if any disturbing, i am so sorry, but hope to have any chance to work with you, thank you so much.

Minimum Order: 6 gallons

Item Name(EH):#Common Rail Injector Valve Assembly F00RJ01159# Common Rail Injector Valve Assembly F00ZC01310 Common Rail Injector Valve Assembly F00ZC01315 Common Rail Injector Valve Assembly F00ZC01318 Common Rail Injector Valve Assembly F00ZC01330 (8AU) Whats--App 86--1--3--3--8--6--9--0--1--3--1--5 Doney----(a , t)----china-lutong---(dot)----net What is the purpose of the injector valve on a generator? The fuel injector of a diesel generator is an important component in the fuel supply system of a diesel engine to achieve fuel injection. Its function is to atomize the fuel into fine droplets according to the characteristics of the diesel engine mixture and inject it into the specific combustion chamber.

Common Rail Fuel Injector Control Valve F00RJ02130 0 445 110 286 Injector Valve Set 0 445 110 287 Injector Valve Set 0 445 110 288 Injector Valve Set (8AU) Whats--App 86--1--3--3--8--6--9--0--1--3--1--5 Doney----(a , t)----china-lutong---(dot)----net China-Lutong is now one of the specialist Fuel Injection System suppliers and manufacturers. Our aim and business policy is to give the customer a reliable quality product and service, alternative to the OE products. The parts are quality assured to ISO9001: 2015 and are subject to regular internal and external audits ensuring that quality is the highest standard. We are stockiest and also represent Chinese leading manufacturers including of: Fuel injection pumps parts Diesel Injectors, Diesel nozzles VE Pumps, VE injection Pumps Head Rotor, Distributor head Diesel Plunger, Diesel Elements Delivery Valve Common Rail Nozzle, common rail control valve Feed Pump Repair kits Solenoid Valve

Minimum Order: 6 gallons